Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly LH*1, RH*2 via CAN communication. If the SET switch is being pressed when one of the M1, M2 or M3 switches is pressed, or if one of the M1, M2 or M3 switches is pressed within 3 seconds of pressing the SET switch, the main body ECU (multiplex network body ECU) sends an memory request signal to the front power seat switch LH*1, RH*2. After receiving the request signal, the front power seat switch LH*1, RH*2 memorizes the location data of each motor.

1*: for LHD

2*: for RHD

WIRING DIAGRAM

E340092E05
0.198,3.417 1.99,3.896 1.792,0.479 10 false Main Body ECU (Multiplex Network Body Computer) 0.063,1.76 2.208,2.167 2.146,0.406 10 false Front Power Seat Switch LH 3.219,3.365 3.5,3.51 0.281,0.146 10 false I41 4.396,1.021 4.604,1.167 0.208,0.146 10 false M1 4.396,1.531 4.604,1.677 0.208,0.146 10 false M2 4.396,2.01 4.604,2.156 0.208,0.146 10 false M3 4.344,2.521 4.604,2.667 0.26,0.146 10 false MM 3.458,2.938 3.917,3.104 0.458,0.167 10 false GND 5.542,0.927 5.771,1.083 0.229,0.156 10 false M1 5.552,1.417 5.781,1.573 0.229,0.156 10 false M2 5.552,1.906 5.781,2.063 0.229,0.156 10 false M3 5.552,2.833 5.667,2.99 0.115,0.156 10 false E 5.542,2.406 5.99,2.563 0.448,0.156 10 false MRY 5.354,1.906 5.469,2.063 0.115,0.156 10 false 2 4.688,1.906 4.802,2.063 0.115,0.156 10 false 4 5.354,1.417 5.469,1.573 0.115,0.156 10 false 3 4.688,1.417 4.802,1.573 0.115,0.156 10 false 3 5.344,0.927 5.458,1.083 0.115,0.156 10 false 4 4.688,0.927 4.802,1.083 0.115,0.156 10 false 2 5.354,2.406 5.469,2.563 0.115,0.156 10 false 5 4.688,2.406 4.802,2.563 0.115,0.156 10 false 1 5.354,2.833 5.469,2.99 0.115,0.156 10 false 6 3.26,2.833 3.385,2.99 0.125,0.156 10 false 7 3.219,3.563 4.844,3.896 1.625,0.333 10 false Outer Mirror Control ECU Assembly LH 5.49,3.427 5.688,3.573 0.198,0.146 10 false q1 5.49,3.604 7.021,3.781 1.531,0.177 10 false Seat Memory Switch LH 0.677,4.344 1.438,4.5 0.76,0.156 10 false : CAN Line 0.052,0.042 0.906,0.406 0.854,0.365 12 false for LHD:

E340092E06
0.198,3.417 2.135,3.875 1.938,0.458 10 false Main Body ECU (Multiplex Network Body Computer) 0.063,1.76 2.208,2.167 2.146,0.406 10 false Front Power Seat Switch RH 3.219,3.365 3.5,3.51 0.281,0.146 10 false I38 4.396,1.021 4.604,1.167 0.208,0.146 10 false M1 4.396,1.531 4.604,1.677 0.208,0.146 10 false M2 4.396,2.01 4.604,2.156 0.208,0.146 10 false M3 4.344,2.521 4.604,2.667 0.26,0.146 10 false MM 3.458,2.938 3.917,3.104 0.458,0.167 10 false GND 5.542,0.927 5.771,1.083 0.229,0.156 10 false M1 5.552,1.417 5.781,1.573 0.229,0.156 10 false M2 5.552,1.906 5.781,2.063 0.229,0.156 10 false M3 5.552,2.833 5.667,2.99 0.115,0.156 10 false E 5.542,2.406 5.99,2.563 0.448,0.156 10 false MRY 5.354,1.906 5.469,2.063 0.115,0.156 10 false 2 4.688,1.906 4.802,2.063 0.115,0.156 10 false 4 5.354,1.417 5.469,1.573 0.115,0.156 10 false 3 4.688,1.417 4.802,1.573 0.115,0.156 10 false 3 5.344,0.927 5.458,1.083 0.115,0.156 10 false 4 4.688,0.927 4.802,1.083 0.115,0.156 10 false 2 5.354,2.406 5.469,2.563 0.115,0.156 10 false 5 4.688,2.406 4.802,2.563 0.115,0.156 10 false 1 5.354,2.833 5.469,2.99 0.115,0.156 10 false 6 3.26,2.833 3.385,2.99 0.125,0.156 10 false 7 3.219,3.563 4.844,3.896 1.625,0.333 10 false Outer Mirror Control ECU Assembly RH 5.49,3.427 5.688,3.573 0.198,0.146 10 false p1 5.49,3.604 7.021,3.781 1.531,0.177 10 false Seat Memory Switch RH 0.677,4.344 1.438,4.5 0.76,0.156 10 false : CAN Line 0.052,0.042 0.906,0.406 0.854,0.365 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The front power seat control system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the main body ECU (multiplex network body ECU), refer to the Entry and Start System (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).



PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL FUNCTION
a.

Check that each function of the power seat operates normally by using the front power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

OK:

Each function of power seat operates normally by using seat switches.




OK

2.READ VALUE USING GTS (SEAT MEMORY SWITCH)

NG

2.READ VALUE USING GTS (SEAT MEMORY SWITCH)
a.

Check the Data List for proper functioning of the seat memory switch LH*1, RH*2 (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>DATA LIST / ACTIVE TEST).

·

*1: for LHD

·

*2: for RHD


Mirror
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SET Switch Seat memory SET switch signal / ON or OFF ON: Seat memory SET switch on
OFF: Seat memory SET switch off
-
M1 Switch Seat memory switch 1 signal / ON or OFF ON: Seat memory switch 1 on
OFF: Seat memory switch 1 off
-
M2 Switch Seat memory switch 2 signal / ON or OFF ON: Seat memory switch 2 on
OFF: Seat memory switch 2 off
-
M3 Switch Seat memory switch 3 signal / ON or OFF ON: Seat memory switch 3 on
OFF: Seat memory switch 3 off
-


OK:

On the GTS screen, each item changes between ON and OFF according to above chart.



OK

3.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

6.INSPECT SEAT MEMORY SWITCH
3.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Driver Seat:
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -


OK:

Buzzer sounds normally.




OK

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Replace the outer mirror control ECU assembly LH*1, RH*2 with a new or known good one (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL).

*1: for LHD

*2: for RHD



NEXT

5.CHECK SEAT MEMORY SWITCH FUNCTION
5.CHECK SEAT MEMORY SWITCH FUNCTION
a.

Perform a memory operation properly (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the seat memory SET switch and 2 or more of the seat memory switches (for example, seat memory switch 1 and seat memory switch 2) are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat memory switch function operates normally.




OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

6.INSPECT SEAT MEMORY SWITCH

*1: for LHD

*2: for RHD

a.

Remove the seat memory switch LH*1, RH*2 (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH(w/ Seat Position Memory System)>REMOVAL).


b.

Inspect the seat memory switch LH*1, RH*2 (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH(w/ Seat Position Memory System)>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - SEAT MEMORY SWITCH)

NG

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - SEAT MEMORY SWITCH)

*1: for LHD

*2: for RHD

a.

Disconnect the I41*1, I38*2 ECU connector.


b.

Disconnect the q1*1, p1*2 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
I41-2 (M1) - q1-4 (M1) Always Below 1 Ω
I41-3 (M2) - q1-3 (M2) Always Below 1 Ω
I41-4 (M3) - q1-2 (M3) Always Below 1 Ω
I41-1 (MM) - q1-5 (MRY) Always Below 1 Ω
I41-7 (GND) - Body ground Always Below 1 Ω
q1-6 (E) - Body ground Always Below 1 Ω
I41-2 (M1) - Body ground Always 10 kΩ or higher
I41-3 (M2) - Body ground Always 10 kΩ or higher
I41-4 (M3) - Body ground Always 10 kΩ or higher
I41-1 (MM) - Body ground Always 10 kΩ or higher
I41-7 (GND) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
I38-2 (M1) - p1-4 (M1) Always Below 1 Ω
I38-3 (M2) - p1-3 (M2) Always Below 1 Ω
I38-4 (M3) - p1-2 (M3) Always Below 1 Ω
I38-1 (MM) - p1-5 (MRY) Always Below 1 Ω
I38-7 (GND) - Body ground Always Below 1 Ω
p1-6 (E) - Body ground Always Below 1 Ω
I38-2 (M1) - Body ground Always 10 kΩ or higher
I38-3 (M2) - Body ground Always 10 kΩ or higher
I38-4 (M3) - Body ground Always 10 kΩ or higher
I38-1 (MM) - Body ground Always 10 kΩ or higher
I38-7 (GND) - Body ground Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR