When the refreshing seat switch is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly receives the signal and operates the front seat heater.
Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no LIN communication malfunctions before troubleshooting this symptom.
Clear the DTCs (See page Vehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B14C1 is not output | A |
| DTC B14C1 is output | B |
A
B
Disconnect the seat heater control sub-assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c13-4 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| c13-4 (B) - Body ground | Engine switch off (IG) | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c13-6 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Seat Heater Control Sub-assembly LH) |
OK
NG
Remove the seat heater control sub-assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c13-5 (THL) - SHL-2 (TH1) | Always | Below 1 Ω |
| c13-5 (THL) or SHL-2 (TH1) - Body ground | Always | 10k Ω or higher |
| c13-2 (PL) - SHL-3 (TH2) | Always | Below 1 Ω |
| c13-2 (PL) or SHL-3 (TH2) - Body ground | Always | 10k Ω or higher |
| *a | Seat Heater Control Sub-assembly LH
(to Air Conditioning Amplifier Assembly) |
| *b | Seat Heater Control Sub-assembly LH
(to Front Seat Cushion Heater Assembly LH) |
OK
NG
Remove the front seat cushion heater assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT CUSHION HEATER>REMOVAL).
Inspect the front seat cushion heater assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT CUSHION HEATER>INSPECTION).
OK
NG
Remove the front seatback heater assembly LH (See page Vehicle Interior>SEAT>FRONT SEATBACK HEATER>REMOVAL).
Inspect the front seatback heater assembly LH (See page Vehicle Interior>SEAT>FRONT SEATBACK HEATER>INSPECTION).
OK
NG
Disconnect the E35 and E36 air conditioning amplifier assembly connectors.
Disconnect the c13 seat heater control sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E36-16 (SHD+) - c13-1 (SWL) | Always | Below 1 Ω |
| E36-16 (SHD+) or c13-1 (SWL) - Body ground | Always | 10 kΩ or higher |
| E35-19 (TSL) - c13-5 (THL) | Always | Below 1 Ω |
| E35-19 (TSL) or c13-5 (THL) - Body ground | Always | 10 kΩ or higher |
| E35-34 (SG-4) - c13-2 (PL) | Always | Below 1 Ω |
| E35-34 (SG-4) or c13-2 (PL) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the seat heater control sub-assembly LH with a new or known good one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).
Check that the front seat heater system is operated normally.
The front seat heater operates normally.
NG
OK
Replace the air conditioning amplifier assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Check that the front seat heater system is operated normally.
The front seat heater operates normally.
OK
NG