Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
72607
1.INSTALL REAR SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY
Install the 4 lock strikers with the 10 bolts.
87212K
2.INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Conditioning System)
58510D
3.INSTALL FRONT FLOOR CARPET ASSEMBLY
87174
4.INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)
87217B
5.INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System)
62520P
6.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
w/ Sliding Roof:
Install the front quarter trim panel assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>INSTALLATION).
w/o Sliding Roof:
Install the front quarter trim panel assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>INSTALLATION).
62510P
7.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
w/ Sliding Roof:
Install the front quarter trim panel assembly RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>INSTALLATION).
w/o Sliding Roof:
Install the front quarter trim panel assembly RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>INSTALLATION).
71845B
8.INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)
58574A
9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
10.INSTALL REAR NO. 2 SEAT ASSEMBLY
for Face to Face Seat Type:
Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION).
except Face to Face Seat Type:
Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(except Face to Face Seat Type)>INSTALLATION).
67918E
11.INSTALL REAR DOOR SCUFF PLATE LH
67917C
12.INSTALL REAR DOOR SCUFF PLATE RH
51775
13.INSTALL REAR STEP COVER
71696
14.INSTALL REAR NO. 2 SEAT PROTECTOR
Attach the 10 claws to install the 2 seat protectors.
71695C
15.INSTALL REAR NO. 1 SEAT PROTECTOR
Attach the 10 claws to install the 2 seat protectors.
71300S
16.INSTALL REAR NO. 1 SEAT ASSEMBLY RH
Install the rear No. 1 seat assembly RH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>INSTALLATION).
71400S
17.INSTALL REAR NO. 1 SEAT ASSEMBLY LH
Temporarily install the seat assembly with the 4 bolts.
Be careful not to damage the vehicle body.
Tighten the bolts in the order shown in the illustration.
w/ Rear Seat Side Airbag:
Connect the connector.
w/ Seat Heater System:
Connect the connector.
71691K
18.INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER
Attach the 2 clips and 2 claws to install the cover.
71691H
19.INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER
Attach the 2 clips and 2 claws to install the cover.
71692K
20.INSTALL REAR NO. 5 SEAT CUSHION HINGE COVER
Return the seat to the upright position.
Attach the 7 claws to install the cover.
71692H
21.INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER
Attach the 6 claws to install the cover.
22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
23.CHECK SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
71400S
24.INSPECT REAR NO. 1 SEAT ASSEMBLY LH
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch to ON.
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.