Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255632 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 72664 1.INSTALL REAR SEAT LOCK CONTROL LEVER LH

B181797

a.

Install the lock control lever with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 71016A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

B181798

a.

Temporarily install the seat cushion frame with the 5 nuts and bolt.


b.

Tighten the 5 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Using a T40 "TORX" socket, tighten the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 79120B 3.INSTALL NO. 1 SEAT LEG ASSEMBLY LH

B181799

a.

Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 87501B 5.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

B182640

a.

Attach the 2 claws to install the seat heater control.


Hide 71386A 6.INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

B182639

a.

Install the holder bracket with the 2 screws.


b.

Connect the seat wire connector.


Hide 72620B 7.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

a.
B181796E04
1.594,0.135 1.49,0.135 false 1.49,0.135 1.49,0.604 false 1.49,0.604 1.688,1.135 false 1.625,0.052 2.365,0.469 0.74,0.417 10 true Cable Tie

Attach the clamp to install the seat lock cable.


b.

Attach the 3 cable clamps to connect the 3 cables.


c.

Connect the cable and install a new cable tie.


d.
B181203

Install the lower seat track bracket with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 78091 8.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

B181795

a.

Install the 2 fold seat lock control cables.


b.

Attach the 2 cable clamps to connect the 2 cables.


Hide 71018 9.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

a.
B184962

Install the lower seatback cover.


b.
B181793

Temporarily install the seatback frame with the 4 bolts.


c.

LH Side:

Using a T40 "TORX" socket, tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

RH Side:

Using a T55 "TORX" socket, tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 78920 10.INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

B184052

a.

Attach the clamp to install the lock control cable.


b.

Attach the 2 cable clamps to connect the cable.


Hide 72580A 11.INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH

B181792

a.

Attach the clamp to install the adjusting cable.


b.

Attach the 2 cable clamps to connect the cable.


Hide 71099 14.INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

B184963

a.

Attach the 4 claws to install the cover.


b.

Install the 4 screws.


Hide 71379B 15.INSTALL REAR SEATBACK HINGE COVER LH

B181237

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 71833A 16.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B181790

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 71834B 17.INSTALL REAR NO. 2 SEAT RECLINING COVER LH

B181197

a.

Attach the clamp to install the cover.


b.

Install the screw.


Hide 71834D 18.INSTALL REAR SEAT RECLINING COVER LH

B181196

a.

Attach the claw to install the cover.


b.

Install the screw.


Hide 66990 19.INSTALL CUP HOLDER ASSEMBLY (w/ Center Armrest)

a.
B184039

Attach the 2 clips to install the cup holder.


b.
B190297

Install the 2 screws.


Hide 72832A 20.INSTALL NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)

B184038

a.

Attach the 2 claws and 4 clips to install the 2 armrest plates.


Hide 71960B 21.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

Hide 72830 22.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)

B181252

a.

Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72569 23.INSTALL SEATBACK STOPPER PLATE

a.

w/ Center Armrest:

i.

Install the bush to the stopper plate.


ii.
B181250

Temporarily install the stopper plate with the 3 bolts.


iii.

Using a T40 "TORX" socket, tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Tighten the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



b.

w/o Center Armrest:

i.

Install the bush to the stopper plate.


ii.
B181251

Temporarily install the stopper plate with the 3 bolts.


iii.

Using a T40 "TORX" socket, tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Tighten the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 87510Q 24.INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

a.
B378981E10
0.222,2.541 1.127,2.720 0.906,0.180 10 Name Stamp 2.335,2.639 1.336,2.639 false 2.387,2.02 2.732,2.129 0.345,0.108 2.618,2.127 2.326,2.643 false

Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad LH.


b.

Install the seatback heater with new tack pins.


Hide 71078S 25.INSTALL REAR SEPARATE TYPE SEATBACK COVER

a.
B184037E01
2.17,0.096 3.173,0.488 1.003,0.392 10 Hog Ring Pliers 2.136,0.182 2.033,0.182 false 2.033,0.182 1.827,1.534 false

w/ Center Armrest:

Using hog ring pliers, install the seatback cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B189167E01
2.073,0.141 3.093,0.492 1.020,0.350 10 Hog Ring Pliers 2.042,0.221 1.939,0.221 false 1.939,0.221 1.678,1.549 false

w/o Center Armrest:

Using hog ring pliers, install the seatback cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.
B184024

w/ Rear Seat Side Airbag:

Connect the seatback cover bracket to the seatback pad.


Hide 26.INSTALL SEATBACK COVER WITH PAD

a.

Install the seatback cover with pad.


b.
B184030

w/ Center Armrest:

Pull out the seat belt.


c.
B189169

w/o Center Armrest:

Pull out the seat belt.


d.

w/ Rear Seat Side Airbag:

Pass the side airbag wire harness through the hole in the seatback.


e.

w/ Seat Heater System:

Pass the seatback heater wire harness through the hole in the seatback.

i.
B184057



ii.
B182598E01
1.302,1.917 1.406,1.917 false 1.406,1.917 1.604,0.729 true 0.688,1.854 1.313,2.177 0.625,0.323 10 false Cable Tie

Connect the seatback heater wire harness and install a new cable tie.



f.
B184020

w/ Rear Seat Side Airbag:

Install the seatback cover bracket to the seat frame with the cap nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



g.
B262669E01
2.096,0.139 3.092,0.322 0.996,0.184 10 Hog Ring Pliers 2.052,0.224 1.949,0.224 false 1.949,0.224 1.703,1.543 false

w/ Center Armrest:

Using hog ring pliers, install new hog rings to the seatback frame.


h.
B262670E01
2.164,0.133 3.160,0.317 0.996,0.184 10 Hog Ring Pliers 2.12,0.219 2.017,0.219 false 2.017,0.219 1.771,1.538 false

w/o Center Armrest:

Using hog ring pliers, install new hog rings to the seatback frame.


Hide 73375B 27.INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

B181239

a.

Attach the 4 claws to install the cover.


b.

Install the screw.


Hide 73237 28.INSTALL SHOULDER BELT ANCHOR COVER

B184040

a.

Attach the 2 claws to install the cover.


Hide 71931B 29.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.
B181190

w/ Center Armrest:

Attach the 4 claws to install the 2 supports.


b.
B181243

w/o Center Armrest:

Attach the 8 claws to install the 4 supports.


Hide 71940A 30.INSTALL REAR SEAT HEADREST ASSEMBLY

Hide 71702B 31.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.
B184026

w/ Center Armrest:

i.

Push the board down to attach the 2 claws on the bottom.


ii.

Attach the 2 claws on the top of the board to install it.



b.
B189166

w/o Center Armrest:

i.

Push the board down to attach the 3 claws on the bottom.


ii.

Attach the 3 claws on the top of the board to install it.



Hide 72997B 32.INSTALL REAR SEATBACK COVER

B182667

a.

Attach the 4 claws to install the cover.


Hide 87510P 33.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

a.
B378974E10
0.14,1.972 0.989,2.184 0.849,0.211 10 Name Stamp 2.008,1.878 2.353,1.987 0.345,0.108 2.007,1.962 1.842,2.082 1.842,2.082 1.18,2.082 false

Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad LH.


b.

Install the seat cushion heater with new tack pins.


Hide 71076S 34.INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

B184036E01
2.16,0.084 3.177,0.379 1.017,0.295 10 Hog Ring Pliers 2.142,0.171 2.021,0.171 false 2.021,0.171 1.816,1.535 false

a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B181234E01
1.417,0.427 1.323,0.427 false 1.323,0.427 1.323,0.896 false 1.323,0.896 0.948,1.5 true 1.302,0.917 0.917,1.781 true 1.323,0.896 2.406,1.781 true 1.469,0.344 2.552,0.688 1.083,0.344 10 true Fastening Tape

Attach the 3 pieces of fastening tape.


Hide 35.INSTALL SEAT CUSHION COVER WITH PAD

a.

Install the seat cushion cover with pad.


b.

w/ Rear Seat Side Airbag:

Pass the side airbag wire harness through the hole in the seat cushion.


c.

w/ Seat Heater System:

i.
B184056

Pass the seatback heater wire harness through the hole in the seat cushion.


ii.
B182596

Connect the 2 seat heater connectors.



d.

w/ Rear Seat Side Airbag:

Attach the side airbag wire harness clamps.


Hide 78091A 38.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

Hide 72203 39.INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY

a.
B181183

Attach the cable clamp to connect the cable.


b.
B181182

Attach the 2 cable clamps to connect the 2 cables.


c.
B182656

Install the seat track handle with the 2 screws.


Hide 78956 40.INSTALL REAR SEAT UNDER TRAY COVER LH

B181181

a.

Attach the 4 claws to install the cover.


b.

Install the 2 screws.


Hide 72995 41.INSTALL REAR SEAT CUSHION COVER RH

B181231

a.

Attach the 2 claws to install the cover.


b.

Install the 4 screws.


Hide 79123 42.INSTALL NO. 1 SEAT CUSHION PLATE

B181180

a.

Attach the 3 claws to install the seat cushion plate.


Hide 76974E 43.INSTALL REAR UNDER SIDE COVER LH

B181230

a.

Attach the 2 claws and 2 clips to install the cover.


b.

Install the 5 screws.


c.
B181229

Attach the 10 claws.


Hide 71369B 44.INSTALL REAR SEATBACK STAY COVER LH

B181226

a.

Attach the 2 claws to install the cover.


b.

Install the screw.


Hide 73178B 45.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B181228

Install the anchor cover cap with the screw.


b.
B184029

Attach the claw to close the cap.


Hide 71301B 46.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017

a.

Install the hinge with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71302B 47.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

a.
B181176

Attach the cable clamp to connect the cable.


b.
B184045

Install the hinge with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

w/ Rear Seat Side Airbag:

Attach the wire harness clamp.


d.

w/ Seat Heater System:

Attach the wire harness clamp.


Hide 71469 48.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the wire harness, and attach 2 claws to close the protector.


b.
B182595

Attach the claw to install the protector to the seat hinge.


c.

Install the clip.


d.
B184016

w/ Rear Seat Side Airbag:

Attach the claw to install the wire harness connector.


e.

w/ Seat Heater System:

Attach the claw to install the wire harness connector.


Hide 71778 49.INSTALL REAR SEAT SIDE HINGE MALE COVER RH

a.
B181173

Attach the clip to install the cover.


Hide 71779 50.INSTALL REAR SEAT SIDE HINGE MALE COVER LH

a.

Attach the clip to install the cover.


Hide 71777 51.INSTALL REAR SEAT SIDE HINGE FEMALE COVER

a.
B181172

Attach the 6 claws to install the 2 covers.


Hide 78950C 52.INSTALL FOLD SEAT STOPPER BAND ASSEMBLY

a.

Install the fold seat stopper band to the seat leg side cover.


Hide 79965 53.INSTALL REAR NO. 2 SEAT LEG SIDE COVER

a.
B184044

Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.


b.
B181224

Attach the 4 claws to install the seat leg side cover.


c.

Install the 4 screws.


Hide 79951 54.INSTALL NO. 1 SEAT CUSHION COVER

B181223

a.

Attach the 4 claws to install the 2 covers.


Hide 72265 55.INSTALL UPPER SEAT TRACK RAIL COVER RH

B184041

a.

Attach the 2 claws to install the cover.


Hide 72266 56.INSTALL UPPER SEAT TRACK RAIL COVER LH

B184028

a.

Attach the 2 claws to install the cover.


Hide 71833A 57.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B184015

a.

Attach the 4 claws to install the cover.


b.

Install the 2 screws.


Hide 71834G 58.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B184027E01
1.833,0.365 1.948,0.531 0.115,0.167 10 true 1 1.458,1.052 1.573,1.219 0.115,0.167 10 true 2

a.

Attach the 3 claws in the order shown in the illustration to install the cover.


b.

Install the 2 screws.


Hide 72526A 59.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B184013

a.

Install the release handle with the screw.


Hide 72329 60.INSTALL SEAT ADJUSTER BOLT COVER

B184012

a.

Attach the 2 claws to install the cover.