Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
72664
1.INSTALL REAR SEAT LOCK CONTROL LEVER LH
Install the lock control lever with the bolt.
71016A
2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Temporarily install the seat cushion frame with the 5 nuts and bolt.
Tighten the 5 nuts.
Using a T40 "TORX" socket, tighten the bolt.
79120B
3.INSTALL NO. 1 SEAT LEG ASSEMBLY LH
Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.
73390A
4.INSTALL REAR SEAT INNER BELT ASSEMBLY
87501B
5.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
Attach the 2 claws to install the seat heater control.
71386A
6.INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)
Install the holder bracket with the 2 screws.
Connect the seat wire connector.
72620B
7.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Attach the clamp to install the seat lock cable.
Attach the 3 cable clamps to connect the 3 cables.
Connect the cable and install a new cable tie.
Install the lower seat track bracket with the 2 nuts.
78091
8.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
Install the 2 fold seat lock control cables.
Attach the 2 cable clamps to connect the 2 cables.
71018
9.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH
Install the lower seatback cover.
Temporarily install the seatback frame with the 4 bolts.
LH Side:
Using a T40 "TORX" socket, tighten the 2 bolts.
RH Side:
Using a T55 "TORX" socket, tighten the 2 bolts.
78920
10.INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY
Attach the clamp to install the lock control cable.
Attach the 2 cable clamps to connect the cable.
72580A
11.INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH
Attach the clamp to install the adjusting cable.
Attach the 2 cable clamps to connect the cable.
73320A
12.INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
73375B
13.INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH
71099
14.INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH
Attach the 4 claws to install the cover.
Install the 4 screws.
71379B
15.INSTALL REAR SEATBACK HINGE COVER LH
Attach the claw to install the cover.
Install the screw.
71833A
16.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
Attach the claw to install the cover.
Install the screw.
71834B
17.INSTALL REAR NO. 2 SEAT RECLINING COVER LH
Attach the clamp to install the cover.
Install the screw.
71834D
18.INSTALL REAR SEAT RECLINING COVER LH
Attach the claw to install the cover.
Install the screw.
72806B
19.INSTALL REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY (w/ Center Armrest)
Attach the 2 claws and install the rear center seat armrest cup holder sub-assembly.
72808A
20.INSTALL SEAT CENTER ARMREST BRACKET SUB-ASSEMBLY (w/ Center Armrest)
Install the seat center armrest bracket sub-assembly.
72805B
21.INSTALL REAR CENTER SEAT ARMREST DOOR SUB-ASSEMBLY (w/ Center Armrest)
Install the 2 nuts.
Attach the 3 clips and install the rear center seat armrest door sub-assembly.
71836C
22.INSTALL REAR SEATBACK MOULDING LH (w/ Center Armrest)
Attach the guide and claw.
Install the rear seatback moulding LH.
71835C
23.INSTALL REAR SEATBACK MOULDING RH (w/ Center Armrest)
Install the guide and claw.
Install the rear seatback moulding RH.
72860
24.INSTALL REAR CENTER SEAT ARMREST BOX ASSEMBLY (w/ Center Armrest)
Install the rear center seat armrest box assembly.
72803D
25.INSTALL REAR CENTER SEAT ARMREST PANEL SUB-ASSEMBLY (w/ Center Armrest)
While pushing in the installation direction shown in the illustration, attach the 2 guides.
Attach the 6 claws.
Install the rear center seat armrest panel sub-assembly with the screw.
Attach the 2 claws to install the rear seat center armrest cover sub-assembly.
Attach the 13 claws in the order shown in the illustration to install the rear seat center armrest cover sub-assembly.
Attach the 6 claws in the order shown in the illustration to install the rear seat center armrest cover sub-assembly.
72830
26.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)
Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.
72569
27.INSTALL SEATBACK STOPPER PLATE
w/ Center Armrest:
Install the bush to the stopper plate.
Temporarily install the stopper plate with the 3 bolts.
Using a T40 "TORX" socket, tighten the 2 bolts.
Tighten the bolt.
w/o Center Armrest:
Install the bush to the stopper plate.
Temporarily install the stopper plate with the 3 bolts.
Using a T40 "TORX" socket, tighten the 2 bolts.
Tighten the bolt.
71960B
28.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)
87510Q
29.INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad LH.
Install the seatback heater with new tack pins.
71078S
30.INSTALL REAR SEPARATE TYPE SEATBACK COVER
w/ Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
w/o Center Armrest:
Using hog ring pliers, install the seatback cover with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
w/ Rear Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
31.INSTALL SEATBACK COVER WITH PAD
Install the seatback cover with pad.
w/ Center Armrest:
Pull out the seat belt.
w/o Center Armrest:
Pull out the seat belt.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seatback.
Connect the seatback heater wire harness and install a new cable tie.
w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
w/ Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
w/o Center Armrest:
Using hog ring pliers, install new hog rings to the seatback frame.
73174A
32.INSTALL REAR SEAT BELT HOLE COVER LH
Attach the 4 claws to install the cover.
Install the screw.
73237
33.INSTALL SHOULDER BELT ANCHOR COVER
Attach the 2 claws to install the cover.
71931B
34.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
w/ Center Armrest:
Attach the 4 claws to install the 2 supports.
w/o Center Armrest:
Attach the 8 claws to install the 4 supports.
71940A
35.INSTALL REAR SEAT HEADREST ASSEMBLY
71702B
36.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
w/ Center Armrest:
Push the board down to attach the 2 claws on the bottom.
Attach the 2 claws on the top of the board to install it.
w/o Center Armrest:
Push the board down to attach the 3 claws on the bottom.
Attach the 3 claws on the top of the board to install it.
72997B
37.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the cover.
87510P
38.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad LH.
Install the seat cushion heater with new tack pins.
71076S
39.INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 3 pieces of fastening tape.
40.INSTALL SEAT CUSHION COVER WITH PAD
Install the seat cushion cover with pad.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seat cushion.
Connect the 2 seat heater connectors.
w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.
73320A
41.CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
73390C
42.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
78091A
43.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
72203
44.INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY
Attach the cable clamp to connect the cable.
Attach the 2 cable clamps to connect the 2 cables.
Install the seat track handle with the 2 screws.
78956
45.INSTALL REAR SEAT UNDER TRAY COVER LH
Attach the 4 claws to install the cover.
Install the 2 screws.
72995
46.INSTALL REAR SEAT CUSHION COVER RH
Attach the 2 claws to install the cover.
Install the 4 screws.
79123
47.INSTALL NO. 1 SEAT CUSHION PLATE
Attach the 3 claws to install the seat cushion plate.
76974E
48.INSTALL REAR UNDER SIDE COVER LH
Attach the 2 claws and 2 clips to install the cover.
Install the 5 screws.
Attach the 10 claws.
71369B
49.INSTALL REAR SEATBACK STAY COVER LH
Attach the 2 claws to install the cover.
Install the screw.
73178B
50.INSTALL SEAT BELT ANCHOR COVER CAP
Install the anchor cover cap with the screw.
Attach the claw to close the cap.
71301B
51.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
Install the hinge with the 2 nuts.
71302B
52.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
Attach the cable clamp to connect the cable.
Install the hinge with the 2 nuts.
w/ Rear Seat Side Airbag:
Attach the wire harness clamp.
w/ Seat Heater System:
Attach the wire harness clamp.
71469
53.INSTALL REAR NO. 2 SEAT PROTECTOR
Install the wire harness, and attach 2 claws to close the protector.
Attach the claw to install the protector to the seat hinge.
Install the clip.
w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.
w/ Seat Heater System:
Attach the claw to install the wire harness connector.
71778
54.INSTALL REAR SEAT SIDE HINGE MALE COVER RH
Attach the clip to install the cover.
71779
55.INSTALL REAR SEAT SIDE HINGE MALE COVER LH
Attach the clip to install the cover.
71777
56.INSTALL REAR SEAT SIDE HINGE FEMALE COVER
Attach the 6 claws to install the 2 covers.
78950C
57.INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
Install the fold seat stopper band to the seat leg side cover.
79965
58.INSTALL REAR NO. 2 SEAT LEG SIDE COVER
Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.
Attach the 4 claws to install the seat leg side cover.
Install the 4 screws.
79951
59.INSTALL NO. 1 SEAT CUSHION COVER
Attach the 4 claws to install the 2 covers.
72265
60.INSTALL UPPER SEAT TRACK RAIL COVER RH
Attach the 2 claws to install the cover.
72266
61.INSTALL UPPER SEAT TRACK RAIL COVER LH
Attach the 2 claws to install the cover.
71833A
62.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
Attach the 4 claws to install the cover.
Install the 2 screws.
71834G
63.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the 2 screws.
72526A
64.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Install the release handle with the screw.
72329
65.INSTALL SEAT ADJUSTER BOLT COVER
Attach the 2 claws to install the cover.