Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1422/22  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.

DTC Code DTC Detection Condition Trouble Area
B1422/22 An open or short in the compressor lock sensor circuit.
·

CAN communication line

·

Cooler compressor assembly

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E334419E01
6.055,1.214 6.502,1.392 0.447,0.178 10 MGC 4.685,0.808 5.132,0.987 0.447,0.178 10 ECM 6.055,3.768 6.502,3.946 0.447,0.178 10 LOCK 6.055,4.231 6.502,4.409 0.447,0.178 10 SG-2 1.398,1.46 2.265,1.638 0.867,0.178 10 A/C COMP 3.099,2.023 3.967,2.201 0.867,0.178 10 MG CLT 0.028,1.311 1.047,1.561 1.019,0.251 10 from IG1 Relay 5.509,4.894 5.883,5.073 0.374,0.178 10 E81 5.846,3.768 6.220,3.946 0.374,0.178 10 8 5.776,4.231 6.150,4.409 0.374,0.178 10 13 5.776,1.214 6.150,1.392 0.374,0.178 10 20 3.706,1.214 4.080,1.392 0.374,0.178 10 2 3.706,1.638 4.080,1.816 0.374,0.178 10 3 4.393,3.088 4.767,3.266 0.374,0.178 10 3 4.393,3.788 4.767,3.966 0.374,0.178 10 1 4.393,4.23 4.767,4.409 0.374,0.178 10 2 3.934,3.088 4.308,3.266 0.374,0.178 10 MG+ 3.885,3.788 4.308,3.966 0.423,0.178 10 SSR+ 2.546,3.432 4.181,3.610 1.635,0.178 10 Magnet Clutch Assembly 2.437,4.669 4.468,4.848 2.031,0.178 10 C30 2.437,4.825 4.468,5.004 2.031,0.178 10 Cooler Compressor Assembly 5.509,5.058 7.153,5.460 1.644,0.402 10 Air Conditioning Amplifier Assembly 0.656,5.351 2.686,5.530 2.031,0.178 10 : CAN Communication Line 3.934,4.23 4.308,4.409 0.374,0.178 10 SSR- 2.932,1.214 3.306,1.392 0.374,0.178 10 1 2.932,1.638 3.306,1.816 0.374,0.178 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

ECM malfunctions can affect the storage of this DTC. Therefore, check all ECM DTCs and confirm that the system is normal before performing the following inspection.


·

The air conditioning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.INSPECT MAGNET CLUTCH ASSEMBLY

b.

Inspect the magnet clutch assembly.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).

U166594E01
0.094,0.072 0.363,0.234 0.269,0.162 10 *a 4.354,0.072 4.623,0.234 0.269,0.162 10 *b 1.39,0.234 1.807,0.397 0.417,0.162 10 LOCK 1.81,0.302 1.991,0.302 1.991,0.302 2.157,0.971 false 1.164,0.467 1.528,0.630 0.364,0.162 10 SG-2 2.206,0.404 2.488,0.566 0.282,0.162 10 E81 4.168,0.826 4.510,0.988 0.341,0.162 10 GND 1.529,0.537 1.709,0.537 1.709,0.537 1.903,0.967 false

Text in Illustration
*a Component with harness connected
((Air Conditioning Amplifier Assembly)
*b Waveform


b.

Measure the waveform of the connector.

Measurement Condition
Item Contents
Terminal No. (Symbol) E81-8 (LOCK) - E81-13 (SG-2)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition
·

Engine running

·

A/C switch on

·

Blower switch LO



OK:

Waveform varies with the blower level.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.INSPECT COOLER COMPRESSOR ASSEMBLY
3.INSPECT COOLER COMPRESSOR ASSEMBLY

b.

Inspect the cooler compressor assembly.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY -COOLER COMPRESSOR ASSEMBLY)

B

C

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY -COOLER COMPRESSOR ASSEMBLY)
a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Disconnect the C30 cooler compressor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-8 (LOCK) - C30-1 (SSR+) Always Below 1 Ω
E81-13 (SG-2) - C30-2 (SSR-) Always Below 1 Ω
C30-1 (SSR+) - C30-2 (SSR-) Always Below 1 Ω
E81-8 (LOCK) or C30-1 (SSR+) - Body ground Always 10 kΩ or higher
E81-13 (SG-2) or C30-2 (SSR-) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR