Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1422  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly sends an air conditioning operation request signal to the ECM via direct line, and the ECM sends a magnet clutch operation permission signal to the air conditioning amplifier assembly via direct line.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the cooler compressor assembly is locked and turns the magnet clutch assembly off.

DTC Code DTC Detection Condition Trouble Area
B1422 An open or short in the compressor lock sensor circuit.
·

Cooler compressor assembly

·

Harness or connector

·

Magnet clutch relay (MG CLT)

·

Air conditioning amplifier assembly

·

ECM

·

CAN communication system



WIRING DIAGRAM

E236888E01
1.547,1.075 1.873,1.263 0.327,0.188 10 AC1 1.547,0.682 1.873,0.880 0.327,0.197 10 ACT 5.4,1.089 5.777,1.325 0.378,0.237 10 AC1 5.102,0.989 5.364,1.139 0.262,0.150 10 17 5.4,0.696 5.777,0.933 0.378,0.237 10 ACT 5.102,0.596 5.364,0.747 0.262,0.150 10 27 5.4,1.789 5.777,2.026 0.378,0.237 10 MGC 1.895,2.701 3.000,3.142 1.105,0.441 10 Magnet Clutch Relay (MG CLT) 5.102,1.689 5.364,1.839 0.262,0.150 10 20 2.722,1.695 2.838,1.846 0.116,0.150 10 2 1.932,1.695 2.048,1.846 0.116,0.150 10 1 2.744,2.241 2.860,2.392 0.116,0.150 10 3 1.94,2.241 2.056,2.392 0.116,0.150 10 5 1.115,1.946 1.624,2.120 0.508,0.174 10 A/C IG 0.135,1.809 0.784,2.172 0.650,0.363 10 IG1 NO.2 Relay 1.038,1.416 1.403,1.608 0.364,0.193 10 ECM 5.4,3.502 5.847,3.662 0.447,0.160 10 LOCK 5.407,4.514 5.806,4.681 0.399,0.167 10 SG-5 4.418,3.385 4.592,3.559 0.174,0.174 10 1 3.042,2.241 3.217,2.416 0.174,0.174 10 3 3.214,2.241 3.611,2.397 0.397,0.156 10 MG+ 3.042,3.389 3.217,3.564 0.174,0.174 10 2 3.033,4.013 4.990,4.210 1.957,0.197 10 Cooler Compressor Assembly 4.619,4.872 6.863,5.076 2.244,0.204 10 Air Conditioning Amplifier Assembly 5.159,3.352 5.313,3.494 0.154,0.142 10 8 5.094,4.387 5.285,4.560 0.191,0.173 10 35 3.033,3.842 3.335,3.991 0.302,0.149 10 C30 4.639,4.727 4.948,4.883 0.309,0.156 10 E81 3.973,3.399 4.369,3.555 0.397,0.156 10 SSR+ 3.214,3.399 3.611,3.555 0.397,0.156 10 SSR- 0.838,5.03 2.517,5.223 1.679,0.193 10 CAN Communication Line 2.332,0.699 2.641,0.855 0.309,0.156 10 A52 1.954,0.699 2.262,0.855 0.309,0.156 10 A38 2.332,1.092 2.641,1.248 0.309,0.156 10 A52 2.388,0.515 2.572,0.671 0.184,0.156 10 18 2.01,0.515 2.193,0.671 0.184,0.156 10 18 2.388,0.917 2.572,1.072 0.184,0.156 10 30 2.01,0.917 2.193,1.072 0.184,0.156 10 30 2.388,1.295 2.572,1.451 0.184,0.156 10 *2 2.01,1.295 2.193,1.451 0.184,0.156 10 *1 1.954,1.092 2.262,1.248 0.309,0.156 10 A38 0.258,5.559 1.016,5.715 0.758,0.156 10 *2: for RHD 0.258,5.307 1.016,5.462 0.758,0.156 10 *1: for LHD

CAUTION / NOTICE / HINT

HINT:

As DTC B1422 is also output when the fan & generator V-belt is damaged or loose, inspect the belt before performing troubleshooting.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.INSPECT MAGNET CLUTCH RELAY (MG CLT)

B

C

2.INSPECT MAGNET CLUTCH RELAY (MG CLT)
a.
E350079E01
2.646,0.688 2.896,0.438 false 2.469,1.135 2.917,1.448 false 2.333,1.479 1.906,1.771 false 1.99,0.708 1.677,0.51 false 2.958,0.313 3.115,0.51 0.156,0.198 10 false 1 2.958,1.396 3.115,1.594 0.156,0.198 10 false 5 1.792,1.74 1.948,1.938 0.156,0.198 10 false 3 1.542,0.396 1.698,0.594 0.156,0.198 10 false 2 1.396,1.198 1.552,1.396 0.156,0.198 10 false 2 0.354,0.76 0.51,0.958 0.156,0.198 10 false 3 0.354,1.198 0.51,1.396 0.156,0.198 10 false 1 1.385,0.74 1.542,0.938 0.156,0.198 10 false 5

Remove the magnet clutch relay (MG CLT).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - BATTERY, AIR CONDITIONING AMPLIFIER AND COOLER COMPRESSOR)

NG

REPLACE MAGNET CLUTCH RELAY (MG CLT)

3.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - BATTERY, AIR CONDITIONING AMPLIFIER AND COOLER COMPRESSOR)
a.

Remove the magnet clutch relay (MG CLT).


b.

Disconnect the E81 air conditioning amplifier assembly connector.


c.

Disconnect the C30 cooler compressor assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Magnet clutch relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
Magnet clutch relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Magnet clutch relay terminal 2 - E81-20 (MGC) Always Below 1 Ω
Magnet clutch relay terminal 3 - C30-3 (MG+)
Magnet clutch relay terminal 1 - Body ground Always 10 kΩ or higher
Magnet clutch relay terminal 2 - Body ground
Magnet clutch relay terminal 3 - Body ground
Magnet clutch relay terminal 4 - Body ground




OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U166137E02
1.604,1.802 1.271,1.323 false 0.156,0.073 0.375,0.24 0.219,0.167 10 false *a 1.833,0.469 2.115,0.635 0.281,0.167 10 false E81 1.406,1.813 1.792,1.979 0.385,0.167 10 false MGC

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E81-20 (MGC) - Body ground
·

Engine idling

·

Blower switch LO level

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

Blower switch LO level

·

A/C switch off or on (magnet clutch on not permitted)


11 to 14 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



OK

5.INSPECT COOLER COMPRESSOR ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
5.INSPECT COOLER COMPRESSOR ASSEMBLY
a.
E193115E03
2.569,0.878 2.989,1.053 0.420,0.174 10 SSR+ 0.616,1.162 1.008,1.320 0.392,0.158 10 MG+ 1.653,1.259 1.028,1.259 false 0.444,0.869 0.836,1.028 0.392,0.158 10 SSR- 1.899,0.97 2.495,0.97 false 1.533,0.967 0.908,0.967 false

Remove the cooler compressor assembly.



b.

Check the magnet clutch operation.

OK:
Measurement Connection Specified Condition
Battery positive (+) → 3 (MG+)
Battery negative (-) → cooler compressor assembly body
Magnet clutch engages



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) 20°C (68°F) 160 to 320 Ω


Result
Result Proceed to
OK A
NG (for 1VD-FTV) B
NG (for 1GR-FE) C



A

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER COMPRESSOR)

B

C

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER COMPRESSOR)
a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Disconnect the C30 cooler compressor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-8 (LOCK) - C30-1 (SSR+) Always Below 1 Ω
E81-35 (SG-5) - C30-2 (SSR-) Always Below 1 Ω
E81-8 (LOCK) - Body ground Always 10 kΩ or higher
E81-35 (SG-5) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E81-17 (AC1) - A38-30 (AC1) Always Below 1 Ω
E81-27 (ACT) - A38-18 (ACT) Always Below 1 Ω
E81-17 (AC1) - Body ground Always 10 kΩ or higher
E81-27 (ACT) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E81-17 (AC1) - A52-30 (AC1) Always Below 1 Ω
E81-27 (ACT) - A52-18 (ACT) Always Below 1 Ω
E81-17 (AC1) - Body ground Always 10 kΩ or higher
E81-27 (ACT) - Body ground Always 10 kΩ or higher




OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U166138E02
1.26,1.802 1.49,1.323 false 2.573,1.813 2.229,1.417 false 0.156,0.073 0.375,0.24 0.219,0.167 10 false *a 1.833,0.469 2.115,0.635 0.281,0.167 10 false E81 1.063,1.813 1.448,1.979 0.385,0.167 10 false ACT 2.375,1.823 2.76,1.99 0.385,0.167 10 false AC1

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E81-17 (AC1) - Body ground
·

Engine idling

·

Blower switch LO level

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch LO level

·

A/C switch off


11 to 14 V
E81-27 (ACT) - Body ground
·

Engine idling

·

Blower switch LO level

·

A/C switch on (magnet clutch on)


Below 1 V
·

Engine idling

·

Blower switch LO level

·

A/C switch off or on (magnet clutch off)


11 to 14 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

9.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
9.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Check the air conditioning system to check it functions properly.

OK:

Air conditioning system functions operate normally.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)

B

C