A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
89226B
1.INSTALL NO. 2 MULTIPLEX NETWORK BODY ECU
Install the multiplex network body ECU with the bolt.
Connect the 2 connectors.
62597A
2.INSTALL SIDE TRIM BOX
Install the side trim box with the 9 screws.
62598D
3.INSTALL SIDE TRIM BOX COVER
Install the side trim box cover.
62605Q
4.INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH
Install the quarter trim lid.
62522A
5.INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)
Attach the 6 clips to install the quarter trim cover.
62521B
6.INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)
Use the same procedures described for the LH side.
71866B
7.INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Attach the 6 clips to install the rear No. 2 seat cover bezel.
71865A
8.INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedures described for the rear No. 2 seat cover bezel.
72058C
9.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)
72057A
10.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedures described for the LH side.
62526D
11.INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)
Attach the 4 claws to install the cover.
62516B
12.INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)
Use the same procedures described for the LH side.
62525D
13.INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)
Attach the 4 claws to install the cover.
62515B
14.INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)
Attach the 4 claws to install the cover.
Install the duct with the 6 screws.
66992
15.INSTALL NO. 2 CUP HOLDER
Attach the 3 claws to install the cup holder.
Install the 5 screws.
66991B
16.INSTALL NO. 1 CUP HOLDER
Attach the 3 claws to install the cup holder.
Install the 5 screws.
62502B
17.INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH
Attach the 4 claws to install the quarter trim cover.
Install the 7 screws.
w/ Rear Heater:
Install the duct with the 8 screws.
62501C
18.INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH
Attach the 4 claws to install the quarter trim cover.
Install the 7 screws.
73372C
19.INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH
Install the hanger with 2 new spring nuts.
73371C
20.INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH
Use the same procedures described for the LH side.
73371A
21.INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedure to install the hanger on the other side.
Install the hanger with 2 new spring nuts.
62488A
22.INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Attach the 7 claws to install the cover.
62487A
23.INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedures described for the LH side.
73034
24.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 6 claws to install the plate.
73033
25.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedures described for the LH side.
73024
26.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Slide the plate in the direction shown in the illustration and attach the 6 claws to install the plate.
73023
27.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedures described for the LH side.
67916
28.INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH
Attach the 3 clips to install the rear door scuff plate outside.
67915
29.INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH
Use the same procedures described for the LH side.
67912A
30.INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH
Attach the 4 clips to install the front door scuff plate outside.
67911B
31.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedures described for the LH side.
67881A
32.INSTALL BACK DOOR WEATHERSTRIP
Install the back door weatherstrip as shown in the illustration.
62332A
33.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Install the rear door opening trim weatherstrip as shown in the illustration.
62331A
34.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedures described for the LH side.
62312B
35.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip as shown in the illustration.
62311B
36.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedures described for the LH side.
63310
37.INSTALL ROOF HEADLINING ASSEMBLY
for Manual Seat:
When installing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.
for Power Seat:
When installing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.
for Power Seat:
After moving the seats, disconnect the cable from the negative (-) battery terminal.
Place the headlining in the cabin from the rear of the vehicle as shown in the illustration.
Be careful not to damage the roof headlining when placing it in the cabin.
for 3 Person Seat Type Rear No. 2 Seat:
Attach the 12 claws, 2 clips, 2 guides and 16 fasteners to install the headlining.
except 3 Person Seat Type Rear No. 2 Seat:
Attach the 12 claws, 3 clips, 2 guides and 16 fasteners to install the headlining.
Connect the washer hose.
Connect the antenna cord connector.
Connect the antenna cord connector and attach the 2 clamps.
Install the bolt.
Connect the 3 roof wire connectors and washer hose.
Attach the 4 clamps.
Connect the drive gear connector.
w/ Rain Sensor:
Disconnect the rain sensor connector.
w/ EC Mirror:
Connect the inner mirror connector.
62432C
38.INSTALL FRONT ROOF SIDE RAIL GARNISH LH
Install 3 new clips to the roof side rail garnish.
Attach the 3 clips to install the roof side rail garnish.
62431C
39.INSTALL FRONT ROOF SIDE RAIL GARNISH RH
Use the same procedures described for the LH side.
74630B
40.INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedure to install the 3rd seat assist grip on the other side.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
74610K
41.INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH
w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:
Install the No. 2 assist grip assembly.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
w/ Rear No. 2 Seat, for Face to Face Seat Type:
Install the No. 2 assist grip assembly.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
74610B
42.INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH
Use the same procedures described for the LH side.
74610U
43.INSTALL ASSIST GRIP ASSEMBLY
Use the same procedure to install the assist grip on the other side.
Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.
Install the assist grip.
73139B
44.INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)
Attach the 4 guides and 4 clips to install the seat belt anchor cover.
89943
45.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
87834
46.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
74330C
47.INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor)
Attach the 2 clips to install the center visor.
74330B
48.INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor)
Use the same procedures described for the LH side.
74348
49.INSTALL VISOR HOLDER
Use the same procedures to install the visor holder on the other side.
Attach the 2 claws.
Push the visor holder in to install it.
74320
50.INSTALL VISOR ASSEMBLY LH
Install the visor with the 2 screws.
74310
51.INSTALL VISOR ASSEMBLY RH
Use the same procedures described for the LH side.
74325
52.INSTALL VISOR BRACKET COVER
Use the same procedure to install the visor bracket cover on the other side.
Attach the 4 claws to install the visor bracket cover.
81240D
53.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
Install the 2 covers.
Attach the 4 claws to install the room light lens.
Attach the 4 claws to install the room light to the room light switch base.
Attach the 4 claws to install the room light.
81240
54.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
Connect the connector.
Attach the 4 clips to install the room light.
81260A
55.INSTALL MAP LIGHT ASSEMBLY
Connect the connector.
Attach the 2 clips and 2 guides to install the map light.
Install the 2 screws.
Attach the 2 claws to close the 2 covers.
62472D
56.INSTALL REAR UPPER PILLAR GARNISH LH
Attach the 5 clips to install the rear upper pillar garnish.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the seat belt shoulder anchor with the bolt.
Attach the 2 claws to close the seat belt shoulder anchor cover.
62471D
57.INSTALL REAR UPPER PILLAR GARNISH RH
w/o Power Back Door:
Attach the 5 clips to install the rear upper pillar garnish.
w/ Power Back Door:
Pass the power back door rod through the rear upper pillar garnish.
Attach the 5 clips to install the rear upper pillar garnish.
Install the seat belt shoulder anchor with the bolt.
Attach the 2 claws to close the seat belt shoulder anchor cover.
67847
58.INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)
67937B
59.INSTALL BACK DOOR SIDE GARNISH RH (w/ Power Back Door)
67939B
60.INSTALL BACK DOOR GARNISH CENTER (w/ Power Back Door)
62639
61.INSTALL REAR FRONT QUARTER TRIM GARNISH LH
Pass the seat belt anchor through the quarter trim garnish.
Attach the clip and 2 guides to install the quarter trim garnish.
Install the screw.
62638
62.INSTALL REAR FRONT QUARTER TRIM GARNISH RH
Use the same procedures described for the LH side.
62520P
63.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 18 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
Install the rear No. 1 seat belt anchor with the bolt.
Attach the 3 claws to install the cover.
62510P
64.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
w/o Rear Air Conditioning System:
Connect the rear seat lock control lever cable.
w/ Rear Air Conditioning System:
Connect the thermistor connector and rear seat lock control lever cable.
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip and bolt.
w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:
Attach the 16 clips and 2 claws to install the quarter trim panel.
Install the clip.
w/ Rear No. 2 Seat, except Face to Face Seat Type:
Install the rear No. 2 seat belt anchor with the bolt.
Attach the 3 claws to install the cover.
Install the rear No. 1 seat belt anchor with the bolt.
Attach the 3 claws to install the cover.
71845B
65.INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)
Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
62412
66.INSTALL CENTER PILLAR GARNISH LH
Pass the seat belt anchor through the center pillar garnish.
Attach the 2 clips and 2 guides to install the center pillar garnish.
Install the bolt.
62411
67.INSTALL CENTER PILLAR GARNISH RH
Use the same procedures described for the LH side.
74620A
68.INSTALL REAR ASSIST GRIP ASSEMBLY
Use the same procedure to install the rear assist grip on the other side.
Attach the 2 claws to install the rear assist grip.
Install the 2 bolts.
Attach the 4 claws to install the 2 assist grip plugs.
62414A
69.INSTALL CENTER LOWER PILLAR GARNISH LH
for Manual Seat:
When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.
for Power Seat:
When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
for Power Seat:
After moving the front seat, disconnect the cable from the negative (-) battery terminal.
Attach the 2 claws and 7 clips to install the center lower pillar garnish.
Install the seat belt anchor with the bolt.
62413A
70.INSTALL CENTER LOWER PILLAR GARNISH RH
Use the same procedures described for the LH side.
62422
71.INSTALL CENTER PILLAR GARNISH COVER LH
for Manual Seat:
When installing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.
for Power Seat:
When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
for Power Seat:
After moving the front seat, disconnect the cable from the negative (-) battery terminal.
Attach the 2 clips and 2 guides to install the cover.
62421
72.INSTALL CENTER PILLAR GARNISH COVER RH
Use the same procedures described for the LH side.
62212
73.INSTALL FRONT PILLAR GARNISH LH
for 9, 14 Speakers:
Connect the speaker connector.
Attach the clip and 3 guides to install the front pillar garnish.
62211
74.INSTALL FRONT PILLAR GARNISH RH
Use the same procedures described for the LH side.
74610A
75.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
Use the same procedure to install the front assist grip on the other side.
Attach the 2 claws to install the front assist grip.
Install the 2 bolts.
Attach the 4 claws to install the 2 assist grip plugs.
58574A
76.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
Attach the 6 clips to install the support plate.
67918E
77.INSTALL REAR DOOR SCUFF PLATE LH
Attach the 3 claws and 4 clips to install the scuff plate.
Install the screw.
67917C
78.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedures described for the LH side.
51775
79.INSTALL REAR STEP COVER
Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
67914B
80.INSTALL FRONT DOOR SCUFF PLATE LH
Attach the 7 claws and 4 clips to install the scuff plate.
67913B
81.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedures described for the LH side.
82.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)
Install the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(except Face to Face Seat Type)>INSTALLATION).
83.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)
Use the same procedures described for the LH side.
84.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)
Install the rear No. 2 seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>INSTALLATION).
85.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)
Use the same procedures described for the LH side.
86.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).