Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255743 BACK DOOR A

DOOR / HATCH  BACK DOOR  REASSEMBLY  


PROCEDURE

Hide 67290 1.INSTALL BACK DOOR DAMPER ASSEMBLY (w/ Power Back Door)

a.
B193807

When reusing the back door damper assembly:

i.

Install the back door damper assembly with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



b.
B309325

When installing a new back door damper assembly:

i.

With closing the tail gate, install a new back door damper assembly with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 65707A 2.INSTALL TAIL GATE STAY SUB-ASSEMBLY LH

a.

Clean the threaded surface on the vehicle body with a non-residue solvent.


b.

Apply adhesive to the threads of the screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using a T40 "TORX" wrench, install the 2 screws and tail gate stay.


Hide 65706A 3.INSTALL TAIL GATE STAY SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 69390A 4.INSTALL LOWER TAIL GATE LOCK ASSEMBLY LH

a.

w/o Power Back Door:

i.

Using a T30 "TORX" wrench, install the 3 screws and lower tail gate lock assembly LH.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Power Back Door:

i.

Using a T30 "TORX" wrench, install the 4 screws and lower tail gate lock assembly LH.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Connect the connector.



Hide 69690 5.INSTALL BACK DOOR REMOTE CONTROL ASSEMBLY

a.

w/o Power Back Door:

i.

Connect the left side cable.


ii.

Using a T30 "TORX" wrench, install the 2 screws and back door remote control assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Power Back Door:

i.

Connect the connector.


ii.

Using a T30 "TORX" wrench, install the 2 screws and back door remote control assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 69380A 6.INSTALL LOWER TAIL GATE LOCK ASSEMBLY RH

a.

w/o Power Back Door:

i.

Connect the cable to the lower tail gate lock assembly RH.


ii.

Using a T30 "TORX" wrench, install the 3 screws and lower tail gate lock assembly RH.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Power Back Door:

i.

Using a T30 "TORX" wrench, install the 4 screws and lower tail gate lock assembly RH.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Connect the connector.



Hide 69291 7.INSTALL BACK DOOR INSIDE HANDLE ASSEMBLY

a.

Install the back door handle grommet.


b.

Install the screw and back door inside handle assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68846B 8.INSTALL BACK DOOR TORSION BAR GUIDE

a.

Attach the 2 claws to install the back door torsion bar guide.


Hide 68870 9.INSTALL LOWER BACK DOOR TORSION BAR ASSEMBLY

a.

Install the 4 bolts and lower back door torsion bar assembly.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 10.INSTALL SPARE TIRE

Hide 11.INSTALL REAR BUMPER ASSEMBLY

a.

for Standard:



b.

w/ Towing Hitch:



c.

w/ Pintle Hook:



Hide 75132C 12.INSTALL REAR LICENSE LIGHT COVER (w/ Tire Carrier)

Hide 81270 13.INSTALL LICENSE PLATE LIGHT ASSEMBLY (w/ Tire Carrier)

Hide 76802C 14.INSTALL NO. 2 BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/ Tire Carrier)

Hide 64780A 15.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

a.

Attach the 16 clips to install the back door trim panel assembly.


b.

Install the 4 bolts.


Hide 64893 16.INSTALL BACK DOOR TRIM COVER RH

a.
B313306

Install the back door trim cover RH as shown in the illustration.


Hide 64894 17.INSTALL BACK DOOR TRIM COVER LH

a.
B313307

Install the back door trim cover LH as shown in the illustration.


Hide 68960 19.INSTALL BACK DOOR STAY ASSEMBLY LH

Hide 68950C 20.INSTALL BACK DOOR STAY ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 85345R 21.INSTALL REAR WASHER NOZZLE (w/ Rear Wiper)

Hide 76085 22.INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 64886B 23.INSTALL BACK DOOR GLASS CHANNEL LH (w/o Power Back Door)

Hide 64885C 24.INSTALL BACK DOOR GLASS CHANNEL RH (w/o Power Back Door)

HINT:

Use the same procedure described for the LH side.


Hide 76801B 25.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 67281F 26.INSTALL LOWER BACK DOOR STOPPER

a.

Install the bolt and lower back door stopper.


Hide 27.INSTALL CUSHION

a.

Install the 2 cushions.


Hide 68281B 28.INSTALL LIFT GATE WEATHERSTRIP

a.

Attach the 25 clips to install the lift gate weatherstrip.

NOTICE:

Do not pull strongly on the lift gate weatherstrip as it may tear.



Hide 86790D 29.INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Rear View Monitor System)

Hide 84840G 30.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY

Hide 81271 31.INSTALL LICENSE PLATE LIGHT LENS (for Standard)

Hide 84931C 32.INSTALL BACK DOOR CONTROL SWITCH (w/ Power Back Door)

Hide 69358 33.INSTALL BACK DOOR LOCK PROTECTOR (w/ Power Back Door)

Hide 69350 34.INSTALL BACK DOOR LOCK ASSEMBLY

Hide 69321 35.INSTALL BACK DOOR LOCK COVER

Hide 85110R 36.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 85143R 37.INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

a.
B186887E05
1.615,0.792 1.552,0.938 1.552,0.938 1.917,0.802 true 1.365,0.865 1.573,1.063 0.208,0.198 10 false *1

Apply MP grease to the entire inner surface of the rear wiper motor grommet.

Text in Illustration
*1 MP Grease

HINT:

Make sure that the hole does not get clogged with grease and the grooves in the grommet are filled with grease.



b.
E156014E05
1.104,0.25 1.302,0.25 1.302,0.25 1.542,0.833 false 0.917,0.156 1.177,0.344 0.26,0.188 10 false *1

Install the rear wiper motor grommet with the position mark facing upward as shown in the illustration.

Text in Illustration
*1 Position Mark


Hide 85241A 38.INSTALL REAR WIPER ARM (w/ Rear Wiper)

a.
B190077E03
2.219,2.875 2.427,2.844 true 2.063,3.146 2.667,3.458 2.667,3.458 2.667,4.031 true 1.49,1.969 2.01,1.146 true 2.583,4.115 2.792,4.313 0.208,0.198 10 false *2 2.5,2.75 2.729,2.969 0.229,0.219 10 false *3 1.375,2.042 1.635,2.24 0.26,0.198 10 false *1

Operate the rear wiper, and stop the rear wiper motor at the automatic stop position.

Text in Illustration
*1 Wiper Arm Serration
*2 Wiper Pivot Serration
*3 Wire Brush


b.

Clean the wiper arm serration and wiper pivot serration with a wire brush.


c.
E156015E06
1.146,0.188 2.021,0.208 2.021,0.208 3.073,1.542 true 0.99,0.104 1.25,0.323 0.26,0.219 10 true *1

Set the head of the blade on the defogger line.

Text in Illustration
*1 Defogger Line


d.

Install the nut and rear wiper arm.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Close the cover.


Hide 84280D 39.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 40.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure described for the LH side.


Hide 74623 41.INSTALL REAR ASSIST GRIP REINFORCEMENT (for Face to Face Seat Type)

a.

Attach the 2 claws to install the rear assist grip reinforcement.


b.

Install the 3 bolts.


Hide 86160T 42.INSTALL REAR HEADER SPEAKER ASSEMBLY (for 14 Speakers)

Hide 67935B 43.INSTALL BACK DOOR GARNISH

a.

Attach the 14 clips to install the back door garnish.


Hide 84901 44.INSTALL DOOR OPENING SWITCH SUB-ASSEMBLY (for Face to Face Seat Type)

Hide 67848C 45.INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)

a.

Connect the connector.


b.

Attach the 4 claws to install the No. 2 back door service hole cover.


Hide 74611B 46.INSTALL ASSIST GRIP (for Face to Face Seat Type)

a.

Install the assist grip with the 2 screws.


Hide 67847 47.INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

a.
B192440

Install the back door stay plate.


b.
B192434

Pass the power back door rod through the hole of the back door service hole cover RH and install the rod with the bolt.

Torque:
: 18 N*m (184 kgf*cm, 13 ft.*lbf)


c.

Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.


d.

Attach the 2 clips and install the back door service hole cover RH.

NOTICE:

If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover, so do not perform this operation with the back door in a fully open position.



Hide 67938A 48.INSTALL BACK DOOR SIDE GARNISH LH

a.

Attach the 3 clips and 2 claws to install the back door side garnish LH.


Hide 67937B 49.INSTALL BACK DOOR SIDE GARNISH RH

a.

w/o Power Back Door:

HINT:

Use the same procedure described for the LH side.



b.

w/ Power Back Door:

i.

Attach the clip and 4 claws to install the back door side garnish RH.



Hide 67939B 51.INSTALL CENTER BACK DOOR GARNISH

a.

Attach the 5 clips and 4 claws to install the center back door garnish.


Hide 69478 52.INSTALL LOWER BACK DOOR STOPPER CUSHION

a.

Install the 2 lower back door stopper cushions with the 4 bolts.


Hide 69195 53.INSTALL BACK DOOR GRIP

a.

Attach the claw.


b.

Install the back door grip with the 2 screws.


c.

Attach the 5 claws to close the cover.


Hide 54.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).