Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

WIRING DIAGRAM

E275629E04
1.24,0.875 1.708,1.073 0.469,0.198 10 false AUTO 1.771,0.76 2.24,0.958 0.469,0.198 10 false 8 5.469,0.854 5.938,1.052 0.469,0.198 10 false AUTO 5.146,1.698 5.958,1.896 0.813,0.198 10 false I4*1, I12*2 5.146,1.885 6.948,2.313 1.802,0.427 10 false Front Power Window Regulator Motor Assembly 0.552,1.708 1.365,1.906 0.813,0.198 10 false I3*1, I25*2 0.531,1.896 2.333,2.323 1.802,0.427 10 false Power Window Regulator Switch Assembly 0.104,2.396 1.01,2.615 0.906,0.219 10 false *1: for LHD 1.229,2.396 2.135,2.615 0.906,0.219 10 false *2: for RHD 5.25,0.75 5.396,0.948 0.146,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

If the front power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

·

Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work.

·

After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>CUSTOMIZE PARAMETERS).

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>HOW TO PROCEED WITH TROUBLESHOOTING).



HINT:

If the pulse sensor built into the front power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>FAIL-SAFE CHART).


PROCEDURE

2.CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH)
a.

Check that the front passenger side door power window moves when the manual up/down function of the power window regulator switch is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK).

OK:

front passenger side door power window moves.




OK

3.READ VALUE USING INTELLIGENT TESTER (FRONT POWER WINDOW REGULATOR MOTOR RH)

NG

3.READ VALUE USING INTELLIGENT TESTER (FRONT POWER WINDOW REGULATOR MOTOR RH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto up/down signal / ON or OFF ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window switch not operated
-

OK:

The display changes according to operation of the power window regulator switch.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
a.
U164022E02
2,1.74 2.417,1.563 false 2.25,3.594 1.656,3.844 false 0.167,2.125 2.479,2.51 2.313,0.385 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.156,0.104 2.469,0.479 2.313,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Switch) 0.625,1.427 0.906,1.615 0.281,0.188 10 false I25 0.688,1.094 0.865,1.281 0.177,0.188 10 false I3 0.719,3.25 0.896,3.438 0.177,0.188 10 false I4 2.479,1.479 2.896,1.646 0.417,0.167 10 false AUTO 2.292,3.51 2.708,3.677 0.417,0.167 10 false AUTO 0.094,3.896 0.885,4.083 0.792,0.188 10 false *1: for LHD 0.115,4.198 0.906,4.385 0.792,0.188 10 false *2: for RHD 0.885,0.979 1.083,1.167 0.198,0.188 10 false *1 0.896,1.281 1.094,1.469 0.198,0.188 10 false *2 0.688,3.583 0.969,3.771 0.281,0.188 10 false I12 0.927,3.135 1.125,3.323 0.198,0.188 10 false *1 0.938,3.438 1.135,3.625 0.198,0.188 10 false *2

Disconnect the I3*1 or I25*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Disconnect the I4*1 or I12*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I3-8 (AUTO) - I4-4 (AUTO) Always Below 1 Ω
I3-8 (AUTO) or I4-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I25-8 (AUTO) - I12-4 (AUTO) Always Below 1 Ω
I25-8 (AUTO) or I12-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

5.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
U164025E02
2.354,3.208 1.438,2.958 false 2.469,2.396 2.021,2.625 false 0.156,1.438 2.656,1.833 2.5,0.396 10 false Component without harness connected: (Power Window Regulator Switch) 0.51,2.573 0.75,2.76 0.24,0.188 10 false I25 0.531,2.24 0.708,2.427 0.177,0.188 10 false I3 2.417,3.135 2.823,3.302 0.406,0.167 10 false AUTO 2.51,2.292 2.917,2.458 0.406,0.167 10 false GND 0.104,3.052 0.875,3.208 0.771,0.156 10 false *2: for RHD 0.104,2.792 0.875,2.948 0.771,0.156 10 false *1: for LHD 0.76,2.448 0.938,2.604 0.177,0.156 10 false *2 0.76,2.125 0.938,2.281 0.177,0.156 10 false *1

a.

Remove the power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
I3-8 (AUTO) - I3-1 (GND) Auto up/down operation Below 1 Ω

for RHD
Tester Connection Switch Condition Specified Condition
I25-8 (AUTO) - I25-1 (GND) Auto up/down operation Below 1 Ω


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH