Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

WIRING DIAGRAM

E275629E05
1.271,0.885 1.74,1.083 0.469,0.198 10 false AUTO 1.771,0.75 1.979,0.948 0.208,0.198 10 false 8 5.469,0.865 5.938,1.063 0.469,0.198 10 false AUTO 5.01,1.615 5.823,1.813 0.813,0.198 10 false J11 5.01,1.781 6.917,2.208 1.906,0.427 10 false Rear Power Window Regulator Motor Assembly LH 0.344,1.615 1.156,1.813 0.813,0.198 10 false J10 0.344,1.781 2.25,2.208 1.906,0.427 10 false Rear Power Window Regulator Switch Assembly LH 5.26,0.75 5.406,0.948 0.146,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

If the rear power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION).

·

Check that the "RL Window Auto Up" and "RL Window Auto Down" power window control system customize settings are "ON" before proceeding with work (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>CUSTOMIZE PARAMETERS).

·

After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.



HINT:

If the pulse sensor built into the rear power window regulator motor assembly LH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly LH at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>FAIL-SAFE CHART).


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
B2311 is output B
B2312 is output C
B2313 is output D
LIN communication system DTCs are output E



A

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

B

C

D

E

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Check that the manual up/down function using the rear power window regulator switch can operate the rear door power window LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK).

OK:

Manual up/down function operates.




OK

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)

NG

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF ON: Rear power window LH auto up/down switch operated
OFF: Rear power window LH switch not operated
-

OK:

The display changes normally when rear power window switch LH is operated.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
a.
U164018E02
2.01,1.833 2.427,1.667 false 1.208,3.646 1.583,3.844 false 0.156,2.146 2.635,2.521 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.156,0.104 2.635,0.479 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Switch) 0.594,1.104 0.844,1.292 0.25,0.188 10 false J10 0.646,3.25 0.896,3.438 0.25,0.188 10 false J11 2.49,1.604 2.906,1.771 0.417,0.167 10 false AUTO 0.802,3.563 1.219,3.729 0.417,0.167 10 false AUTO

Disconnect the J10 switch connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-8 (AUTO) - J11-4 (AUTO) Always Below 1 Ω
J10-8 (AUTO) or J11-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

5.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
U164023E02
1.333,2.979 0.813,3.135 false 2,2.625 2.417,2.427 false 0.104,1.427 2.771,1.823 2.667,0.396 10 false Component without harness connected: (Rear Power Window Regulator Switch LH) 0.479,2.24 0.719,2.427 0.24,0.188 10 false J10 0.406,3.073 0.823,3.24 0.417,0.167 10 false AUTO 2.479,2.354 2.833,2.521 0.354,0.167 10 false GND

a.

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J10-8 (AUTO) - J10-1 (GND) Auto up/down operation Below 1 Ω




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY