Select the Active Test, use the intelligent tester to generate a control command, and check that the lower tail gate lock operates (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Tail Gate Panel Open | Lower tail gate lock | ON / OFF | The back door must be open. |
Lower tail gate lock operates normally.
OK
NG
Check the Data List for proper functioning of the back door remote control (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Handle Switch of tail gate panel | Back door remote control signal / ON or OFF | ON: Back door remote control pulled
OFF: Back door remote control free |
- |
The display is as specified in the normal condition.
OK
NG
for LH:
Remove the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).
Inspect the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).
for RH:
Remove the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).
Inspect the lower tail gate lock assembly RH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LH) | B |
| NG (for RH) | C |
A
B
C
for LH:
Disconnect the h5 lower tail gate lock assembly LH connector.
Disconnect the L51 No. 2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h5-5 (ACT+) - L51-3 (DC+) | Always | Below 1 Ω |
| h5-6 (ACT-) - L51-8 (DC-) | Always | Below 1 Ω |
| h5-5 (ACT+) - Body ground | Always | 10 kΩ or higher |
| h5-6 (ACT-) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the h4 lower tail gate lock assembly RH connector.
Disconnect the L51 No. 2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h4-5 (ACT+) - L51-2 (DC+) | Always | Below 1 Ω |
| h4-6 (ACT-) - L51-1 (DC-) | Always | Below 1 Ω |
| h4-5 (ACT+) - Body ground | Always | 10 kΩ or higher |
| h4-6 (ACT-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the back door remote control assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).
Inspect the back door remote control assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).
OK
NG
Disconnect the h3 back door remote control assembly connector.
Disconnect the L50 No. 2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h3-2 - L50-19 (BDSU) | Always | Below 1 Ω |
| h3-1 - Body ground | Always | Below 1 Ω |
| h3-2 - Body ground | Always | 10 kΩ or higher |
OK
NG