The No. 2 main body ECU receives the half-latch switch, pawl switch and lower tail gate courtesy switch signals from the lower tail gate lock assembly LH and detects the open/closed status of the lower tail gate. DTC B225D is stored when the No. 2 main body ECU receives a half-latch switch, pawl switch or lower tail gate courtesy switch malfunction signal from the lower tail gate lock assembly LH.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B225D | A half-latch switch, pawl switch or lower tail gate courtesy switch malfunction (open or short circuit) signal from the lower tail gate lock LH is received. | ·
Lower tail gate lock assembly LH ·
Harness or connector ·
No. 2 main body ECU |
Check the Data List for proper functioning of the half-latch switch, pawl switch and lower tail gate courtesy switch (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Half Latch Switch LH | Half-latch switch signal / ON or OFF | ON: Lower tail gate open
OFF: Lower tail gate closed |
- |
| Courtesy Switch LH | Lower tail gate courtesy switch LH signal / ON or OFF | ON: Lower tail gate open
OFF: Lower tail gate closed |
- |
| Luggage Pawl switch | Pawl switch signal / ON or OFF | ON: Lower tail gate lock motor operating
OFF: Lower tail gate open or closed |
- |
The display is as specified in the normal condition.
OK
NG
Starting with the lower tail gate closed, open and close the lower tail gate 6 times.
Check for DTCs (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DTC CHECK / CLEAR).
Clear the DTCs (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DTC CHECK / CLEAR).
Starting with the lower tail gate closed, open and close the lower tail gate 6 times.
Recheck for DTCs (See page Vehicle Exterior>DOOR / HATCH>TAIL GATE CLOSER SYSTEM>DTC CHECK / CLEAR).
DTC B225D is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Remove the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).
Inspect the lower tail gate lock assembly LH (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>INSPECTION).
OK
NG
Check the Data List for proper function of the lower tail gate courtesy switch (See page Vehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| LH CTSY SW of Tail Gate Panel | Lower tail gate courtesy switch LH signal / ON or OFF | ON: Tail gate closed
OFF: Tail gate open |
- |
The display is as specified in the normal condition.
OK
NG
Disconnect the h5 lower tail gate lock assembly LH connector.
Disconnect the L50 and L51 No. 2 main body ECU connectors.
Disconnect the L52 power back door unit assembly (power back door ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h5-1 (HAF) - L51-9 (HAF) | Always | Below 1 Ω |
| h5-2 (FUL) - L51-4 (FUL) | Always | Below 1 Ω |
| h5-4 (POL) - L50-15 (POL) | Always | Below 1 Ω |
| h5-3 (E1) - Body ground | Always | Below 1 Ω |
| h5-1 (HAF) - Body ground | Always | 10 kΩ or higher |
| h5-2 (FUL) - Body ground | Always | 10 kΩ or higher |
| h5-4 (POL) - Body ground | Always | 10 kΩ or higher |
OK
NG