Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Vehicle Speed Signal Circuit  


DESCRIPTION

The headlight leveling ECU receives the vehicle speed signal from the combination meter.

WIRING DIAGRAM

E225965E07
1.188,2.667 2.427,3.042 1.24,0.375 10 false Combination Meter Assembly 1.188,2.521 1.51,2.698 0.323,0.177 10 false E7 4.729,2.677 6.25,3.031 1.521,0.354 10 false Headlight Leveling ECU Assembly 4.729,2.51 5.125,2.688 0.396,0.177 10 false E109 4.906,0.958 5.333,1.115 0.427,0.156 10 false SPDR 4.625,0.865 4.844,1.031 0.219,0.167 10 false 16 2.042,0.958 2.292,1.115 0.25,0.156 10 false +S 2.385,0.875 2.604,1.042 0.219,0.167 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the headlight leveling ECU, initialization of the ECU is necessary (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

HL Auto Leveling (w/ Static Headlight Auto Leveling)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed / 0 to 327.67 km/h Actual vehicle speed -

OK:

The display is as specified in the normal condition column.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the E7 combination meter connector.


b.

Disconnect the E109 headlight leveling ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-4 (+S) - E109-16 (SPDR) Always Below 1 Ω
E7-4 (+S) - Body ground Always 10 kΩ or higher




OK

3.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER ASSEMBLY
a.

w/ Multi-information Display:

i.
U166336E01
0.11,0.03 0.359,0.227 0.248,0.198 10 *a 0.426,0.539 0.763,0.708 0.336,0.170 10 E7 2.35,1.231 2.687,1.401 0.336,0.170 10 +S 2.036,0.649 2.35,1.257 false 2.933,2.489 3.300,2.659 0.368,0.170 10 GND 1.257,2.867 1.430,3.037 0.173,0.170 10 A

Remove the combination meter with its connector still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL).



b.

w/o Multi-information Display:

i.

Remove the combination meter with its connector still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/o Multi-information Display)>REMOVAL).



c.

Connect an oscilloscope to the combination meter connector.


d.

Check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) E7-4 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle is driven at approximately 20 km/h (12 mph)

OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG