The main body ECU receives a front fog light switch information signal from the light control switch (front fog switch), and illuminates the front fog lights.
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
Using the GTS, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Fog Light Relay | Front fog light | ON or OFF | - |
Fog light turns on/turns off.
OK
NG
Remove the fog light relay from the engine room relay block, junction block.
Inspect the fog light relay (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the fog light relay from the engine room relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Fog light relay terminal 2 - Body ground | Light control switch tail | 11 to 14 V |
| Fog light relay terminal 5 - Body ground | Always |
| *a | Front view of wire harness connector
(to Fog Light Relay [FR FOG]) |
OK
NG
Remove the fog light relay from the engine room relay block, junction block.
Disconnect the B5*1 and B6*2 light connectors.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Fog light relay terminal 3 - B5-2 (B) | Always | Below 1 Ω |
| B5-1 (E) - Body ground | Always | |
| B5-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Fog light relay terminal 3 - B6-2 (B) | Always | Below 1 Ω |
| B6-1 (E) - Body ground | Always | |
| B6-2 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the fog light relay from the engine room relay block, junction block.
Disconnect the 2H cowl side junction block LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Fog light relay terminal 1 - 2H-31 | Always | Below 1 Ω |
| Fog light relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
for LHD:
Remove the cowl side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).
Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).
for RHD:
Remove the cowl side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL).
Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2H-31 - A-7 (FFGO) | Always | Below 1 Ω |
| *a | Component without harness connected
(Cowl Side Junction Block LH) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D