The headlight leveling ECU*1 or headlight swivel ECU*2 actuates the headlight leveling motors according to the vehicle conditions.
*1: w/ Static Headlight Auto Leveling
*2: w/ Dynamic Headlight Auto Leveling
After replacing the headlight leveling ECU*1 or headlight swivel ECU*2, initialization of the ECU is necessary (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).
*1: w/ Static Headlight Auto Leveling
*2: w/ Dynamic Headlight Auto Leveling
Using the GTS, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| HL Auto Leveling | This test activates the Leveling Motor of the LH and RH headlights. By activating the Leveling Motor, illumination direction of the headlights can be moved up/down. | Up, Down, Stop | Perform the Active Test with the vehicle stopped, the ignition switch ON and the low beam headlights on. |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| HL Auto Leveling | This test activates the Leveling Motor of the LH and RH headlights. By activating the Leveling Motor, illumination direction of the headlights can be moved up/down. | Up, Down, Stop | Perform the Active Test with the vehicle stopped, the ignition switch ON and the low beam headlights on. |
*: Perform the Active Test with the engine running and vehicle stopped.
Headlight leveling motors operate normally.
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Static Headlight Auto Leveling | A |
| w/ Dynamic Headlight Auto Leveling | B |
A
B
Disconnect the E109 headlight leveling ECU connector.
Disconnect the A66*1 or A69*2 headlight leveling motor connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E109-11 (LH+) - A66-2 (LHIG) | Always | Below 1 Ω |
| E109-18 (LHT) - A66-3 (LH T) | Always | Below 1 Ω |
| E109-24 (LH-) - A66-1 (LH E) | Always | Below 1 Ω |
| E109-11 (LH+) - Body ground | Always | 10 kΩ or higher |
| E109-18 (LHT) - Body ground | Always | 10 kΩ or higher |
| E109-24 (LH-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E109-10 (RH+) - A69-2 (RHIG) | Always | Below 1 Ω |
| E109-17 (RHT) - A69-3 (RH T) | Always | Below 1 Ω |
| E109-23 (RH-) - A69-1 (RH E) | Always | Below 1 Ω |
| E109-10 (RH+) - Body ground | Always | 10 kΩ or higher |
| E109-17 (RHT) - Body ground | Always | 10 kΩ or higher |
| E109-23 (RH-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the E101 headlight swivel ECU connector.
Disconnect the A66*1 or A69*2 headlight leveling motor connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E101-1 (SMBL) - A66-2 (LHIG) | Always | Below 1 Ω |
| E101-30 (LH+) - A66-3 (LH T) | Always | Below 1 Ω |
| E101-27 (LH-) - A66-1 (LH E) | Always | Below 1 Ω |
| E101-1 (SMBL) - Body ground | Always | 10 kΩ or higher |
| E101-30 (LH+) - Body ground | Always | 10 kΩ or higher |
| E101-27 (LH-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E101-2 (SMBR) - A69-2 (RHIG) | Always | Below 1 Ω |
| E101-11 (RH+) - A69-3 (RH T) | Always | Below 1 Ω |
| E101-26 (RH-) - A69-1 (RH E) | Always | Below 1 Ω |
| E101-2 (SMBR) - Body ground | Always | 10 kΩ or higher |
| E101-11 (RH+) - Body ground | Always | 10 kΩ or higher |
| E101-23 (RH-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the headlight unit.
for LED Headlight (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY).
for Halogen Headlight and LED Headlight (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight and LED Headlight)>DISASSEMBLY).
Disconnect the headlight leveling motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (LHIG) - 1 | Always | Below 1 Ω |
| 3 (LH T) - 2 | ||
| 1 (LH E) - 3 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (RHIG) - 1 | Always | Below 1 Ω |
| 3 (RH T) - 2 | ||
| 1 (RH E) - 3 |
| *A | for LH |
| *B | for RH |
| *a | Front view of wire harness connector
(to Headlight Leveling Motor) |
| *b | Component without harness connected
(Headlight Unit Assembly) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LED Headlight) | B |
| NG (for Halogen Headlight and LED Headlight) | C |
A
B
C
Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY).
Perform the Active Test of the leveling motors (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
Headlight leveling motors operate normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Static Headlight Auto Leveling) | B |
| NG (w/ Dynamic Headlight Auto Leveling) (for LHD) | C |
| NG (w/ Dynamic Headlight Auto Leveling) (for RHD) | D |
A
B
C
D