Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B124B  Automatic High Beam System  


DESCRIPTION

The main body ECU (multiplex network body ECU) determines the status of the automatic high beam system based on the automatic high beam system signal from the forward recognition camera*1 or inner rear view mirror assembly*2.

*1: w/ Pre-crash Safety System

*2: w/o Pre-crash Safety System


DTC Code DTC Detection Condition Trouble Area
B124B Malfunction in automatic high beam system
·

CAN communication system

·

Main body ECU (multiplex network body ECU)

·

Inner rear view mirror assembly (w/o Pre-crash safety system)

·

Forward recognition camera (w/ Pre-crash safety system)

·

Pre-crash afety system

·

Lane departure alert system

·

SFI system (for 1UR-FE, 3UR-FE)

·

ECD system (for 1VD-FTV)

·

Vehicle stability control system



WIRING DIAGRAM

E349685E01
0.104,0.104 2.49,0.385 2.385,0.281 12 false w/o Pre-crash Safety System: 1.219,1.552 3.604,1.833 2.385,0.281 10 false Inner Rear View Mirror Assembly 5.25,1.521 7.042,1.906 1.792,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.135,2.229 3.521,2.51 2.385,0.281 10 false : CAN Communication Line

E349685E02
0.104,0.104 2.49,0.385 2.385,0.281 12 false w/ Pre-crash Safety System: 1.219,1.552 3.604,1.833 2.385,0.281 10 false Forward Recognition Camera 5.25,1.521 7.042,1.906 1.792,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.135,2.229 3.521,2.51 2.385,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

for LHD with Central Gateway ECU

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

for LHD without Central Gateway ECU

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

for RHD with Central Gateway ECU

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

for RHD without Central Gateway ECU

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

w/ Pre-crash Safety System

This DTC is output simultaneously from the forward recognition camera when DTCs related to the items below are output.

-

Wheel speed sensor malfunction

-

Yaw rate sensor malfunction

-

Steering angle sensor system malfunction

-

CAN communication lost




PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

Result
Result Proceed to
Only DTC B124B is output (w/ Pre-crash Safety System) A
Only DTC B124B is output (w/o Pre-crash Safety System) B
DTC B124B is output at the same time C



A

2.CHECK FORWARD RECOGNITION CAMERA

B

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

C

2.CHECK FORWARD RECOGNITION CAMERA
a.

Check if a dynamic radar cruise control system, lane departure alert system and pre-crash safety system warning message are displayed on the combination meter assembly (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU(MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU(MULTIPLEX NETWORK BODY ECU)

C