Home › Steering › VARIABLE GEAR RATIO STEERING › VARIABLE GEAR RATIO STEERING SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255448 VARIABLE GEAR RATIO STEERING SYSTEM Y

VARIABLE GEAR RATIO STEERING  VARIABLE GEAR RATIO STEERING SYSTEM  CALIBRATION  


CAUTION / NOTICE / HINT

NOTICE:

Use this procedure to center the steering wheel if:

·

The steering actuator assembly has been replaced.

·

The steering control ECU has been replaced.

·

The steering column or steering intermediate shaft has been disconnected.

·

The steering wheel is still off-center after completing the steering angle sensor initialization.



PROCEDURE

1.VGRS SYSTEM CALIBRATION PROCEDURE
Result:
Proceed to
WHEN USING SST CHECK WIRE
WHEN USING INTELLIGENT TESTER



WHEN USING SST CHECK WIRE

2.FACE TIRES STRAIGHT AHEAD

WHEN USING INTELLIGENT TESTER

12.FACE TIRES STRAIGHT AHEAD
2.FACE TIRES STRAIGHT AHEAD
NOTICE:

Drive the vehicle to confirm that the steering wheel is centered.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Click hereSteering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC C1591/51 is not output A
DTC C1591/51 is output B




A

4.PERFORM ACTUATOR ANGLE INITIALIZATION

B

5.FACE TIRES STRAIGHT AHEAD
4.PERFORM ACTUATOR ANGLE INITIALIZATION
SST
09843-18040  

NOTICE:

If the procedures from *1 to *2 are not completed within 1 minute, or if errors are made during these procedures, perform the initialization again from the beginning.


a.
H102392E81
2.397,0.326 2.631,0.477 0.234,0.150 10 CG 1.623,0.863 2.319,0.457 false 1.076,1.797 1.306,1.963 0.230,0.165 10 TS 1.587,1.443 1.266,1.756 false 0.079,0.05 1.420,0.261 1.341,0.211 10 Front view of DLC3: 2.003,1.791 2.391,1.971 0.387,0.179 10 TC 1.772,1.45 2.079,1.757 false

Start the engine.


b.

Center the steering wheel.


c.

Using SST, connect terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) of the DLC3.*1


d.

Disconnect SST from terminal 12 (TS) of the DLC3, and turn the steering wheel to the left 180° or more.


e.

Connect SST to terminal 12 (TS) of the DLC3.


f.

Disconnect SST from terminal 13 (TC) of the DLC3, and turn the steering wheel to the right 180° or more.


g.

Connect SST to terminal 13 (TC) of the DLC3.*2

HINT:

If the master warning light comes on, DTC C1591/51 is stored.



h.

Disconnect SST from the DLC3.


i.

Turn the engine switch off.


Result:
Proceed to
NEXT



NEXT

5.FACE TIRES STRAIGHT AHEAD
5.FACE TIRES STRAIGHT AHEAD
a.

Confirm that the steering wheel is centered when facing the tires straight ahead.

NOTICE:

Drive the vehicle to confirm that the steering wheel is centered.


Result:
Result Proceed to
Steering wheel is off-center A
Steering wheel is centered B




A

6.UNLOCK STEERING ACTUATOR

B

9.ADJUST ACTUATOR ANGLE
6.UNLOCK STEERING ACTUATOR
NOTICE:

Make sure the engine is not running.


a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
C140769E04
0.18,0.059 2.487,0.42 2.307,0.361 10 Rear view of wire harness connector: (to Steering Actuator ) 0.064,1.743 0.585,1.979 0.521,0.236 10 7 (LV+) 1.015,2.208 0.637,1.916 false 0.296,2.717 0.905,2.921 0.609,0.205 10 16 (LG+) 2.108,2.045 2.499,2.333 0.391,0.288 2.155,2.074 2.514,2.321 0.359,0.247 10 E80 0.95,2.306 0.636,2.717 false

Disconnect the E80 connector from the steering actuator.


d.

Connect a jumper wire from terminal 7 (LV+) of the steering actuator to the positive (+) 12 V battery terminal and another jumper wire from terminal 16 (LG+) of the steering actuator to the negative (-) 12 V battery terminal.

NOTICE:

Do not apply voltage for more than 3 minutes.



Result:
Proceed to
NEXT



NEXT

7.STEERING CENTER ADJUSTMENT
7.STEERING CENTER ADJUSTMENT
a.

Center the steering wheel.

NOTICE:

If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION



Result:
Proceed to
NEXT



NEXT

8.LOCK STEERING ACTUATOR
8.LOCK STEERING ACTUATOR
a.

Disconnect the positive (+) and negative (-) 12 V battery jumper wires from the steering actuator.


b.

Connect the E80 connector to the steering actuator.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the steering wheel approximately 3° to the left and right. Confirm that the reaction force can be felt.

NOTICE:
·

If the above procedures are not followed correctly, a DTC will be stored. If a DTC is stored, perform the above procedures again and then check for DTCs.

·

Perform these procedures with the engine switch off.




Result:
Proceed to
NEXT



NEXT

9.ADJUST ACTUATOR ANGLE
9.ADJUST ACTUATOR ANGLE
HINT:

Activating and ending test mode will complete actuator angle adjustment.


a.

Make sure the engine switch is off.

NOTICE:

Do not touch the steering wheel during these procedures.



b.
H102392E80
2.367,0.304 2.600,0.454 0.234,0.150 10 CG 1.605,0.895 2.265,0.457 false 1.128,1.809 1.358,1.974 0.230,0.165 10 TS 1.579,1.435 1.242,1.809 false 0.092,0.03 1.396,0.204 1.304,0.174 10 Front view of DLC3:

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the engine switch on (IG).


d.

Confirm that "VGRS Test Mode" is displayed on the multi-information display when test mode is activated.

HINT:

Wait approximately 5 seconds.



e.

Turn the engine switch off.


f.

Disconnect SST from terminals 12 (TS) and 4 (CG) of the DLC3.


g.

Turn the engine switch on (IG) again.


Result:
Proceed to
NEXT



NEXT

10.CHECK MASTER WARNING LIGHT
10.CHECK MASTER WARNING LIGHT
a.

Confirm that the master warning light is off.


b.

Turn the engine switch off, then on (IG).


c.

Confirm that the master warning light is operating normally.


Result:
Proceed to
NEXT



NEXT

11.CHECK STEERING WHEEL OPERATION
11.CHECK STEERING WHEEL OPERATION
a.

Start the engine.


b.

Perform the steering angle sensor initialization.

Click hereSteering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>INITIALIZATION


c.

Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.


d.

Drive the vehicle and confirm that the steering wheel is centered.


Result:
Proceed to
NEXT



NEXT

END

12.FACE TIRES STRAIGHT AHEAD
NOTICE:

Drive the vehicle to confirm that the steering wheel is centered.


Result:
Proceed to
NEXT



NEXT

13.PERFORM VGRS SYSTEM CALIBRATION
13.PERFORM VGRS SYSTEM CALIBRATION
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Chassis / VGRS / Utility / Steering Angle Adjust. Then, press "Next".


e.

Follow the instructions on the tester, and press "Next".

NOTICE:

Press the "Next" key even if DTC C15B4/71 is output.



f.

Follow the instructions on the tester, and press "Next".


g.

Follow the instructions on the tester, and press "Next".

NOTICE:

Ensure that the engine switch is off.



h.

Follow the instructions on the tester, and press "Next".


i.

Follow the instructions on the tester, and press "Next".

NOTICE:

If the centering of the spiral cable was not confirmed when the steering wheel was installed, confirm the centering of the spiral cable.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION



j.

Follow the instructions on the tester, and press "Next".

NOTICE:

Do not touch the steering wheel during these procedures.



k.

Follow the instructions on the tester, and press "Next".


l.

Follow the instructions on the tester, and press "Next".

NOTICE:

Do not touch the steering wheel during these procedures.



m.

"NOW CALIBRATING" is displayed and the display switches automatically to the next screen.

NOTICE:

Do not touch the steering wheel during these procedures.



n.

"Steering Angle Adjust is complete." is displayed. Then, check that the VGRS system calibration is completed normally.


o.

Select "Exit" to return the display to the "MENU" screen.


Result:
Proceed to
NEXT



NEXT

14.CHECK MASTER WARNING LIGHT
14.CHECK MASTER WARNING LIGHT
a.

Confirm that the master warning light is off.


b.

Turn the engine switch off.


c.

Disconnect the intelligent tester from the DLC3.


d.

Turn the engine switch on (IG).


e.

Confirm that the master warning light is operating normally.


Result:
Proceed to
NEXT



NEXT

15.CHECK STEERING WHEEL OPERATION
15.CHECK STEERING WHEEL OPERATION
a.

Start the engine.


b.

Perform the steering angle sensor initialization.

Click hereSteering>VARIABLE GEAR RATIO STEERING>VARIABLE GEAR RATIO STEERING SYSTEM>INITIALIZATION


c.

Turn the steering wheel from lock to lock and check that it rotates approximately 2.7 turns.


d.

Drive the vehicle and confirm that the steering wheel is centered.


Result:
Proceed to
NEXT



NEXT

END