Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2017.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255050 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 86011A 1.INSTALL NOISE FILTER

a.

Install the 2 noise filters to the cylinder head cover with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 19500 2.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 8 ignition coils with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12315 3.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the mounting bracket with the 4 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 12311 4.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the mounting bracket with the 4 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 11415 5.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the drain cocks.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.
A385327E01
1.781,2.792 1.292,2.688 1.292,2.688 1.594,2.573 true 4.927,2.75 4.49,2.667 4.49,2.667 4.74,2.531 true 0.427,0.208 0.74,0.406 0.313,0.198 10 false *A 3.677,0.208 3.99,0.406 0.313,0.198 10 false *B 1.052,2 1.365,2.198 0.313,0.198 10 false *a 5.865,1.99 6.177,2.188 0.313,0.198 10 false *a 1.073,2.604 1.385,2.802 0.313,0.198 10 false 30° 1.594,3.042 1.906,3.24 0.313,0.198 10 false 50° 4.25,2.604 4.563,2.802 0.313,0.198 10 false 30° 4.74,3.01 5.052,3.208 0.313,0.198 10 false 50°

Install the water drain cocks as shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*A LH
*B RH
*a Front

NOTICE:
·

Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.

·

Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.




c.

Install the water drain cock plugs to the water drain cocks.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 89615 6.INSTALL KNOCK SENSOR

a.
A152496E16
0.188,0.49 0.5,0.813 0.313,0.323 1.063,0.75 1.219,0.958 0.156,0.208 10 true A 1.042,1.125 1.26,1.333 0.219,0.208 10 true B 2.542,0.75 2.698,0.958 0.156,0.208 10 false C 2.938,1.135 3.094,1.344 0.156,0.208 10 true D 0.229,0.563 0.438,0.74 0.208,0.177 10 false *a 0.083,2.323 0.281,2.49 0.198,0.167 10 false *1 0.771,2.531 0.958,2.74 0.188,0.208 10 false *c 0.219,2.813 0.396,2.979 0.177,0.167 10 false *a 1.438,2.896 1.76,3.052 0.323,0.156 10 false 10° 1.438,3.083 1.76,3.24 0.323,0.156 10 false 10° 2.115,2.896 2.438,3.052 0.323,0.156 10 false 10° 2.115,3.073 2.438,3.229 0.323,0.156 10 false 10° 1.833,2.792 2.021,2.979 0.188,0.188 10 false *a 2.844,2.521 3.042,2.698 0.198,0.177 10 false *c 1.802,2.323 2.01,2.521 0.208,0.198 10 false *3 0.375,4.052 0.698,4.208 0.323,0.156 10 false 10° 0.375,4.24 0.698,4.396 0.323,0.156 10 false 10° 0.094,3.99 0.302,4.156 0.208,0.167 10 false *b 1.104,3.698 1.271,3.865 0.167,0.167 10 false *c 0.104,3.458 0.344,3.646 0.24,0.188 10 false *2 1.813,3.448 2.042,3.625 0.229,0.177 10 false *4 3.042,4.063 3.333,4.219 0.292,0.156 10 false 10° 3.042,4.25 3.333,4.406 0.292,0.156 10 false 10° 1.771,3.979 1.958,4.156 0.188,0.177 10 false *b 2.365,3.698 2.542,3.875 0.177,0.177 10 false *c

Install the 4 sensors with the 4 bolts so that the sensors are angled as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Bank 2 Sensor 1
*2 Bank 1 Sensor 1
*3 Bank 2 Sensor 2
*4 Bank 1 Sensor 2
*a Front
*b Rear
*c Top

NOTICE:

The acceptable installation angle of the sensor is between 10° upward and downward from the horizontal position.



Hide 12215 7.INSTALL SEPARATOR CASE

a.
A163108E04
0.667,0.688 0.854,0.854 0.188,0.167 10 true A 1.115,2.323 1.26,2.49 0.146,0.167 10 true B 1.896,0.625 2.042,0.792 0.146,0.167 10 true C 0.333,1.229 0.479,1.396 0.146,0.167 10 true C

After inserting the pipe on the rear of the separator case into the oil return pipe and the pipe on the front into the ventilation pipe, temporarily install bolt A.


b.

Temporarily install bolt B and tighten bolt A.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the bolts labeled C.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Tighten bolt B.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 25 mm (0.984 in.) 6 mm (0.236 in.)
Bolt B and C 16 mm (0.630 in.) 6 mm (0.236 in.)



Hide 82219A 8.INSTALL SENSOR WIRE

a.

Connect the 3 clamps and 4 knock sensor connectors.


Hide 25720 11.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 16206 12.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the water by-pass pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17303 14.INSTALL AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)

a.
A158582

Install the 2 No. 1 air hoses and air pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16355 15.INSTALL FRONT WATER BY-PASS JOINT

Hide 16261G 16.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 16207 17.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 12611 18.INSTALL NO. 1 ENGINE COVER

Hide 11212 19.INSTALL NO. 2 ENGINE COVER

Hide 23901 20.INSTALL NO. 1 FUEL TUBE

Hide 23902 21.INSTALL NO. 2 FUEL TUBE

a.

Install the No. 2 fuel tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17111 22.INSTALL INTAKE MANIFOLD

a.
A184486

Place 2 new gaskets on the intake manifold.


b.

Place the intake manifold on the cylinder head.


c.

Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the wire bracket to the intake manifold with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the No. 1 ventilation hose.


f.

Connect the 2 water by-pass hoses.


g.

Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.


Hide 23250 23.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807 24.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH

Hide 23808 25.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH

Hide 23271H 28.INSTALL NO. 1 FUEL HOSE

Hide 12613 29.INSTALL NO. 3 ENGINE COVER

Hide 12601B 30.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 31.INSTALL ENGINE WIRE

A237008E01
2.178,2.46 2.425,2.635 0.248,0.175 10 45° 2.576,2.846 2.829,3.023 0.253,0.177 10 45° 1.051,2.593 1.318,2.770 0.267,0.177 10 45° 0.639,2.983 0.955,3.160 0.316,0.177 10 45°

a.

Install the engine wire.


b.

Engine Rear Side:

i.

Install the 3 bolts as shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


ii.

Connect the 5 clamps.


iii.

Connect the sensor wire connector.


iv.

w/ Secondary Air Injection System:

Connect the 2 air switching valve connectors.



c.

Engine RH Side:

i.

Connect the 9 clamps.


ii.

Connect the oil level sensor connector.


iii.

Connect the oil pressure sender gauge connector.


iv.

Connect the throttle sensor connector.


v.

Connect the noise filter connector.


vi.

Connect the fuel injector connector.


vii.

Connect the 2 VVT sensor connectors.

HINT:

The wire harnesses on the exhaust side are wrapped with white tape.



viii.

Connect the 4 ignition coil connectors.


ix.

Connect the 2 camshaft timing control valve connectors.

HINT:

The wire harnesses on the exhaust side are wrapped with white tape.




d.

Engine LH Side:

i.

Connect the 7 clamps and install the engine wire with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


ii.

Connect the noise filter connector.


iii.

Connect the fuel injector connector.


iv.

Connect the engine coolant temperature sensor connector.


v.

Connect the purge VSV connector.


vi.

Connect the vacuum switching valve connector (for ACIS).


vii.

Connect the camshaft position sensor connector.


viii.

Connect the 2 VVT sensor connectors.

HINT:

The wire harnesses on the exhaust side are wrapped with white tape.



ix.

Connect the 4 ignition coil connectors.


x.

Connect the 2 camshaft timing control valve connectors.

HINT:

The wire harnesses on the exhaust side are wrapped with white tape.