16322
1.INSTALL WATER INLET PIPE
Apply soapy water to 2 new O-rings and install them to the inlet pipe.
Install the inlet pipe to the No. 1 heat exchanger cover.
11302
2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Apply a light coat of engine oil to a new oil pump gasket.
Install the oil pump gasket.
Apply a light coat of engine oil to a new O-ring.
Install the O-ring.
Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.
| *1 | Continuous line area | *2 | Dashed line area |
| *3 | Diagonal line area | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Area | Seal Packing Diameter | Application Position from Inside Edge of Cover |
|---|---|---|
| Continuous Line Area | 3.0 to 4.0 mm (0.118 to 0.157 in.) | 2.5 mm (0.0984 in.) |
| Dashed Line Area | 6.4 mm (0.252 in.) or more, or within OK area shown in illustration | 7.0 mm (0.276 in.) |
| Diagonal Line Area | 3.0 to 4.0 mm (0.118 to 0.157 in.) | 5.5 mm (0.217 in.) |
| *1 | Seal Packing Thickness mm (in.) |
| *2 | Seal Packing Width mm (in.) |
| *3 | Seal Packing Thickness |
| *4 | Seal Packing Width |
| *5 | OK Area |
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
Temporarily install the timing chain cover with the 28 bolts and nut.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 25 mm (0.984 in.) | 8 mm (0.315 in.) |
| Bolt B | 55 mm (2.17 in.) | 8 mm (0.315 in.) |
| Bolt C | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt D | 35 mm (1.38 in.) | 10 mm (0.394 in.) |
| Bolt E | 55 mm (2.17 in.) | 10 mm (0.394 in.) |
| Bolt F | 80 mm (3.15 in.) | 10 mm (0.394 in.) |
| *1 | Nut |
Make sure that there is no oil on the bolt threads.
Tighten the 3 bolts in several steps in the sequence shown in the illustration.
Temporarily install the fluid coupling bracket with the 4 bolts.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt B | 80 mm (3.15 in.) | 10 mm (0.394 in.) |
Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.
Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.
Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.
Do not start the engine for at least 2 hours after installing.
After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.
11193
3.INSTALL SPARK PLUG TUBE GASKET
11202
4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).
Install a new gasket to the cylinder head cover.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.
Do not start the engine for at least 2 hours after the installation.
11201
5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).
Install a new gasket to the cylinder head cover.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.
Do not start the engine for at least 2 hours after the installation.
Install the noise filter to the cylinder head cover with the bolt.
19500
6.INSTALL IGNITION COIL ASSEMBLY
Install the 8 ignition coils with the 8 bolts.
13521A
7.INSTALL CRANKSHAFT TIMING GEAR KEY
Install the crankshaft timing gear key to the crankshaft.
8.CONNECT WIRE HARNESS CLAMP BRACKET
Connect the bracket to the timing chain cover with the bolt.
13471
9.INSTALL CRANKSHAFT PULLEY
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
Using SST, install the pulley set bolt.
| *a | Hold |
|
Turn |
16603
10.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
Install the idler pulley with the bolt.
16173
11.INSTALL WATER PUMP PULLEY
Temporarily install the pulley with the 4 bolts.
Using SST, hold the pulley and tighten the 4 bolts.
16323
12.INSTALL WATER INLET HOUSING
Install a new gasket to the timing chain cover.
Install the water inlet with the 3 bolts.
| *1 | Gasket |
17303
13.INSTALL AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)
Connect the 2 hoses.
Install the air pipe with the bolt.
12611
14.INSTALL NO. 1 ENGINE COVER
11212
15.INSTALL NO. 2 ENGINE COVER
16355
16.INSTALL FRONT WATER BY-PASS JOINT
Install 2 new gaskets and the water by-pass joint with the 4 nuts.
Connect the No. 2 water by-pass hose to the water by-pass joint.
16206
17.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the 2 hoses.
Install the water by-pass pipe with the 2 bolts.
w/ Secondary Air Injection System:
Connect the air tube with the bolt.
16261G
18.INSTALL NO. 1 WATER BY-PASS HOSE
Install the No. 1 water by-pass hose by connecting the hose to the water inlet housing and front water by-pass joint.
27020
19.INSTALL GENERATOR ASSEMBLY
32907A
20.CONNECT OIL COOLER PIPE ASSEMBLY
44310
21.CONNECT VANE PUMP ASSEMBLY
Before performing the following procedures, move the spacer until the vane pump can be installed.
| *1 | Spacer |
Connect the vane pump to the timing chain cover with the 2 bolts.
17111
22.INSTALL INTAKE MANIFOLD
15671
23.INSTALL OIL FILTER BRACKET
15781
24.INSTALL NO. 1 OIL COOLER BRACKET
16207
25.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the 4 hoses.
Install the water by-pass pipe with the 3 bolts.
83520
26.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
11452
27.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
28.INSTALL OIL FILTER ELEMENT
23902
29.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube with the 2 bolts.
| *A | LH Side |
| *B | RH Side |
88320
30.CONNECT COOLER COMPRESSOR ASSEMBLY
Install the cooler compressor with the stud bolt.
Install the 3 bolts and nut.
Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.
31.CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY
Connect the water pipe and hose to the cylinder head cover with the 2 bolts.
Connect the 3 hoses.
32.CONNECT AIR PUMP HOSE AND WIRE HARNESS (w/ Secondary Air Injection System)
Connect the No. 2 and No. 3 air hoses.
Connect the 2 clamps and air pump wire harness.
33.CONNECT ENGINE WIRE
Connect the 2 clamps and power steering oil pressure switch connector.
Engine Room RH Side:
Connect the 6 clamps.
Connect the throttle position sensor and throttle control motor connector.
w/ Secondary Air Injection System:
Connect the 2 air pump connectors and connector.
Connect the ground wire with the bolt.
Connect the noise filter connector.
Connect the 2 VVT sensor connectors.
Connect the injector connector.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing oil control valve connectors.
Engine Room LH Side:
Connect the cooler compressor connector.
Connect the 3 clamps.
Connect the camshaft position sensor connector.
Connect the 2 camshaft timing oil control valve connectors.
Connect the engine coolant temperature sensor connector.
Connect the 4 clamps.
Connect the ground wire with the bolt.
Connect the noise filter connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the injector connector.
w/ Secondary Air Injection System:
Connect the wire harness clamp and 4 air injection control driver connectors.
Connect the 2 connectors and 2 clips to the engine room junction block.
Install the engine room relay block cover.
16400
34.INSTALL RADIATOR ASSEMBLY
17700
35.INSTALL AIR CLEANER ASSEMBLY
17880
36.INSTALL AIR CLEANER HOSE ASSEMBLY
11209
37.INSTALL V-BANK COVER SUB-ASSEMBLY
39.ADD ENGINE COOLANT
40.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
41.INSPECT FOR OIL LEAK
42.INSPECT FOR COOLANT LEAK
43.INSPECT ENGINE OIL LEVEL
51442
44.INSTALL NO. 2 ENGINE UNDER COVER
51405C
45.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53736G
46.INSTALL FRONT FENDER APRON SEAL FRONT RH
53737B
47.INSTALL FRONT FENDER APRON SEAL LH
55781E
48.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53294C
49.INSTALL RADIATOR SIDE DEFLECTOR LH
32917
50.INSTALL TRANSMISSION OIL COOLER AIR DUCT
52119A
51.INSTALL FRONT BUMPER COVER
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>INSTALLATION)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>INSTALLATION)