Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1661/44  Roll Over Cut Off Indicator Malfunction  


DESCRIPTION

The curtain shield airbag cutoff switch is a mechanism that operates both the right and left sides of the curtain shield airbag and the front seat outer belt when the center airbag sensor detects a roll-over.

The RSCA OFF indicator is installed in the combination meter.

If the curtain shield airbag cutoff switch is operated, the indicator comes on to inform the drive that the roll-over detection system is not working.

The initial setting of the roll-over detection system is on. It automatically operates every time the ignition switch is turned to ON.

DTC Code DTC Detection Condition Trouble Area
B1661/44 When one of the following conditions is met:
·

The center airbag sensor receives an open signal or short to ground in the RSCA OFF indicator circuit.

·

An RSCA OFF indicator malfunction.

·

A center airbag sensor malfunction.


·

Combination meter assembly

·

Curtain shield airbag cutoff switch

·

Center airbag sensor assembly

·

Instrument panel wire

·

No. 3 instrument panel wire



WIRING DIAGRAM

C387685E02
5.74,1.781 6.354,1.979 0.615,0.198 10 false RMIL 5.75,4.188 6.365,4.385 0.615,0.198 10 false RMSW 5.042,1.771 5.5,1.969 0.458,0.198 10 false EL1 4,1.771 4.458,1.969 0.458,0.198 10 false EL1 3.771,4.188 4.229,4.385 0.458,0.198 10 false GE1 3.771,5.427 4.229,5.625 0.458,0.198 10 false GE1 0.115,3.385 1.292,3.792 1.177,0.406 10 false from MPX-B NO. 2 Fuse 1.656,2.854 2.271,3.052 0.615,0.198 10 false E119 1.635,3.042 4.24,3.24 2.604,0.198 10 false Combination Meter 2.135,2.302 3.365,2.5 1.229,0.198 10 false RSCA OFF 0.521,1.656 0.833,1.854 0.313,0.198 10 false 21 0.75,1.667 1.063,1.865 0.313,0.198 10 false B 3.365,1.677 3.979,1.875 0.615,0.198 10 false R/O 3.656,1.677 3.99,1.906 0.333,0.229 10 false 12 5.083,1.552 5.417,1.781 0.333,0.229 10 false 52 4.031,1.563 4.365,1.792 0.333,0.229 10 false 53 5.521,1.677 5.854,1.906 0.333,0.229 10 false 15 5.521,4.104 5.854,4.333 0.333,0.229 10 false 14 5.698,5.615 6.156,5.813 0.458,0.198 10 false E47 5.667,5.771 7.083,6.094 1.417,0.323 10 false Center Airbag Sensor 3.885,5.208 4.042,5.406 0.156,0.198 10 false 3 3.875,3.958 4.031,4.156 0.156,0.198 10 false 4 3.344,4.104 3.552,4.302 0.208,0.198 10 false 8 1.885,4.104 2.094,4.302 0.208,0.198 10 false 11 2.042,4.604 2.656,4.802 0.615,0.198 10 false G27 2.031,4.74 4.438,5 2.406,0.26 10 false Curtain Shield Airbag Cutoff Switch

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK COMBINATION METER (SOURCE VOLTAGE)
a.
U165690E02
1.583,2.052 1.042,2.635 1.042,2.635 0.917,2.635 false 0.26,0.26 2.635,0.948 2.375,0.688 10 false Component with harness connected: (Combination Meter) 0.302,1.896 0.688,2.083 0.385,0.188 10 false E119 0.604,2.573 0.969,2.781 0.365,0.208 10 false R/O

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Remove the combination meter with the connector connected.


d.

Disconnect the connector from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-12 (R/O) - Body ground Ignition switch ON 11 to 14 V



h.

Turn the ignition switch off.



OK

2.CHECK RSCA OFF INDICATOR CIRCUIT

NG

2.CHECK RSCA OFF INDICATOR CIRCUIT
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

C387686E01
3.094,1.573 3.479,1.781 0.385,0.208 5.344,1.448 5.729,1.656 0.385,0.208 4.417,1.708 4.542,2.125 4.542,2.125 4.656,2.125 true 6.271,1.542 6.5,2.146 6.5,2.146 6.594,2.146 true 1.094,1.552 1.094,1.104 1.094,1.104 0.958,1.104 true 1.833,1.552 1.844,0.99 1.844,0.99 1.958,0.99 true 1.469,1.552 1.479,0.656 1.479,0.656 1.594,0.656 true 2.167,1.542 2.323,1.74 0.156,0.198 10 false A 1.906,1.729 2.063,1.938 0.156,0.208 10 false B 1.688,1.729 1.844,1.938 0.156,0.208 10 false C 1.542,1.729 1.698,1.938 0.156,0.208 10 false D 1.313,1.729 1.469,1.938 0.156,0.208 10 false E 1.167,1.719 1.323,1.927 0.156,0.208 10 false F 0.948,1.74 1.104,1.948 0.156,0.208 10 false G 0.677,1.552 0.833,1.76 0.156,0.208 10 false H 3.135,1.594 3.5,1.833 0.365,0.24 10 false E119 5.417,1.469 5.875,1.667 0.458,0.198 10 false E47 4.708,2.063 5.021,2.26 0.313,0.198 10 false R/O 6.635,2.073 7.042,2.271 0.406,0.198 10 false RMIL 3.958,0.99 4.844,1.25 0.885,0.26 10 false Connector E 5.833,0.885 6.719,1.146 0.885,0.26 10 false Connector B 2.021,2 2.896,2.438 0.875,0.438 10 false Center Airbag Sensor 0.219,1.938 1,2.323 0.781,0.385 10 false Combination Meter 0.25,0.927 0.958,1.302 0.708,0.375 10 false Instrument Panel Wire 3.521,0.063 5.177,0.583 1.656,0.521 10 false Front view of wire harness connector: (to Combination Meter) 5.552,0.052 7.104,0.542 1.552,0.49 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2,0.906 3.438,1.104 1.438,0.198 10 false Instrument Panel Wire 1.625,0.583 3.063,0.781 1.438,0.198 10 false No.2 Floor Wire


b.

Disconnect the connector from the combination meter.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-12 (R/O) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-12 (R/O) - E47-15 (RMIL) Always Below 1 Ω
E119-12 (R/O) - Body ground Always 1 MΩ or higher




OK

3.INSPECT CURTAIN SHIELD AIRBAG CUTOFF SWITCH

NG

6.CHECK RSCA OFF INDICAOR CIRCUIT
3.INSPECT CURTAIN SHIELD AIRBAG CUTOFF SWITCH
a.

Remove the curtain shield airbag cutoff switch (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG CUTOFF SWITCH>REMOVAL).


b.


OK

4.CHECK CURTAIN SHIELD AIRBAG CUTOFF SWITCH CIRCUIT

NG

4.CHECK CURTAIN SHIELD AIRBAG CUTOFF SWITCH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C383620E01
2.75,1.531 3.135,1.771 0.385,0.24 4.729,1.51 5.115,1.75 0.385,0.24 6.385,2.146 5.958,1.625 true 0.521,1.448 0.677,1.646 0.156,0.198 10 false F 0.813,1.656 0.969,1.854 0.156,0.198 10 false E 1.042,1.656 1.198,1.854 0.156,0.198 10 false D 1.167,1.656 1.323,1.854 0.156,0.198 10 false C 1.375,1.656 1.531,1.854 0.156,0.198 10 false B 1.688,1.448 1.844,1.646 0.156,0.198 10 false A 2.813,1.573 3.271,1.771 0.458,0.198 10 false G27 2.229,0.135 4.688,0.542 2.458,0.406 10 false Front view of wire harness connector: (to Curtain Shield Airbag Cutoff Switch) 4.771,0.146 7.052,0.51 2.281,0.365 10 false Front view of wire harness connector: (to Center Airbag Sensor) 4.781,1.542 5.24,1.74 0.458,0.198 10 false E47 6.198,2.177 6.813,2.375 0.615,0.198 10 false RMSW 3.26,0.938 4.948,1.135 1.688,0.198 10 false Connector E 5.396,0.833 7.083,1.031 1.688,0.198 10 false Connector B 1.552,1.896 2.438,2.26 0.885,0.365 10 false Center Airbag Sensor 0.042,1.833 0.896,2.385 0.854,0.552 10 false Curtain Shield Airbag Cutoff Switch


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G27-8 - Body ground Ignition switch ON Below 1 V
G27-11 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-14 (RMSW) - G27-8 Always Below 1 Ω
G27-8 - Body ground Always 1 MΩ or higher
G27-11 - Body ground Always Below 1 Ω




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 3 INSTRUMENT PANEL WIRE AND BODY GROUND)
5.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 3 INSTRUMENT PANEL WIRE AND BODY GROUND)
a.

Disconnect the instrument panel wire connector from the No. 3 instrument panel wire.

U165693E01
0.018,1.88 0.973,2.381 0.955,0.500 10 Curtain Shield Airbag Cutoff Switch 1.597,1.96 2.512,2.283 0.915,0.323 10 Center Airbag Sensor 0.538,1.5 0.703,1.675 0.165,0.174 10 F 1.244,1.675 1.529,1.933 0.286,0.258 10 C 1.517,1.675 1.756,1.933 0.239,0.258 10 B 0.816,1.675 0.977,1.864 0.161,0.188 10 E 1.087,1.675 1.326,1.933 0.239,0.258 10 D 1.783,1.509 2.077,1.748 0.295,0.239 10 A 2.361,0.012 4.709,0.387 2.347,0.375 10 Front view of wire harness connector: (to No. 3 Instrument Panel Wire) 4.783,0.012 7.142,0.372 2.359,0.360 10 Front view of wire harness connector: (to Center Airbag Sensor) 3.261,0.988 4.166,1.187 0.906,0.199 10 Connector C 5.414,0.83 6.367,1.050 0.954,0.220 10 Connector B 2.624,1.582 2.967,1.780 0.344,0.198 10 GE1 4.859,1.323 5.214,1.506 0.355,0.184 10 E47 1.533,0.484 2.274,0.820 0.740,0.336 10 Instrument Panel Wire 1.195,0.423 1.29,0.423 1.29,0.423 1.015,1.515 false 0.099,0.337 1.172,0.673 1.074,0.336 10 No. 3 Instrument Panel Wire 1.499,0.542 1.453,0.542 1.453,0.542 1.385,1.522 false 6.258,2.089 7.089,2.245 0.832,0.156 10 RMSW 5.94,1.577 6.236,2.158 false


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GE1-4 - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-14 (RMSW) - GE1-4 Always Below 1 Ω
GE1-4 - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 3 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK RSCA OFF INDICAOR CIRCUIT
a.

Disconnect the No.2 floor wire connector from the instrument panel wire.

C387687E01
3.156,1.396 3.5,1.615 0.344,0.219 5.469,1.479 5.813,1.698 0.344,0.219 1.417,1.333 1.427,0.427 1.427,0.427 1.552,0.427 true 1.719,1.333 1.719,0.802 1.719,0.802 1.854,0.802 true 1.052,1.302 1.052,0.74 1.052,0.74 0.938,0.74 true 6.74,2.104 6.646,2.104 6.646,2.104 6.469,1.594 true 0.135,1.698 0.938,2.281 0.802,0.583 10 false Combination Meter 1.948,1.771 2.833,2.146 0.885,0.375 10 false Center Airbag Sensor 2.052,1.313 2.208,1.51 0.156,0.198 10 false A 1.792,1.5 1.948,1.698 0.156,0.198 10 false B 1.583,1.5 1.74,1.698 0.156,0.198 10 false C 1.479,1.5 1.635,1.698 0.156,0.198 10 false D 1.271,1.5 1.427,1.698 0.156,0.198 10 false E 1.115,1.5 1.271,1.698 0.156,0.198 10 false F 0.885,1.49 1.042,1.688 0.156,0.198 10 false G 0.615,1.313 0.771,1.51 0.156,0.198 10 false H 1.896,0.688 2.979,1.063 1.083,0.375 10 false Instrument Panel Wire 0.208,0.573 0.917,1.031 0.708,0.458 10 false Instrument Panel Wire 1.594,0.375 3.542,0.604 1.948,0.229 10 false No.2 Floor Wire 3.198,1.427 3.542,1.625 0.344,0.198 10 false EL1 5.521,1.51 5.865,1.708 0.344,0.198 10 false E47 3.594,0.063 5.177,0.677 1.583,0.615 10 false Front view of wire harness connector: (to Instrument Panel Wire) 5.885,0.031 7.052,0.875 1.167,0.844 10 false Front view of wire harness connector: (to Center Airbag Sensor) 3.948,0.802 5.635,1 1.688,0.198 10 false Connector E 6.052,1 7.031,1.354 0.979,0.354 10 false Connector B 6.771,2.021 7.156,2.26 0.385,0.24 10 false RMIL


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
EL1-53 - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-15 (RMIL) - EL1-53 Always Below 1 Ω
EL1-53 - Body ground Always 1 MΩ or higher




OK

7.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO.2 FLOOR WIRE AND BODY GOUND)

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO.2 FLOOR WIRE AND BODY GOUND)
a.

Disconnect the instrument panel wire connector from the No.2 floor wire.

C387688E01
3.229,1.292 3.552,1.521 0.323,0.229 5.469,1.313 5.833,1.521 0.365,0.208 1.031,1.323 1.031,0.802 1.031,0.802 0.958,0.802 true 1.406,1.323 1.406,0.375 1.406,0.375 1.5,0.375 true 1.781,1.323 1.781,0.677 1.781,0.677 1.885,0.677 true 6.74,1.958 6.635,1.958 6.635,1.958 6.458,1.406 true 0.292,0.615 1,1.031 0.708,0.417 10 false Instrument Panel Wire 1.938,0.594 3.021,1.01 1.083,0.417 10 false Instrument Panel Wire 1.542,0.302 2.927,0.51 1.385,0.208 10 false No.2 Floor Wire 2.104,1.302 2.26,1.5 0.156,0.198 10 false A 1.844,1.49 2,1.688 0.156,0.198 10 false B 1.625,1.49 1.781,1.688 0.156,0.198 10 false C 1.479,1.49 1.635,1.688 0.156,0.198 10 false D 1.26,1.49 1.417,1.688 0.156,0.198 10 false E 1.115,1.49 1.271,1.688 0.156,0.198 10 false F 0.896,1.49 1.052,1.688 0.156,0.198 10 false G 0.625,1.302 0.781,1.5 0.156,0.198 10 false H 3.26,1.313 3.719,1.51 0.458,0.198 10 false EL1 5.521,1.333 5.979,1.531 0.458,0.198 10 false E47 0.146,1.729 0.958,2.104 0.813,0.375 10 false Combination Meter 1.958,1.75 2.823,2.094 0.865,0.344 10 false Center Airbag Sensor 3.688,0.031 5.115,0.646 1.427,0.615 10 false Front view of wire harness connector: (to No.2 Floor Wire) 5.74,0.031 7.146,0.656 1.406,0.625 10 false Front view of wire harness connector: (to Center Airbag Sensor) 3.958,0.729 4.75,1.063 0.792,0.333 10 false Connector C 6.073,0.833 6.865,1.167 0.792,0.333 10 false Connector B 6.76,1.896 7.135,2.281 0.375,0.385 10 false RMIL


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
EL1-52 - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E47-15 (RMIL) - EL1-52 Always Below 1 Ω
EL1-52 - Body ground Always 1 MΩ or higher




OK

REPLACE NO.2 FLOOR WIRE

NG

REPLACE INSTRUMENT PANEL WIRE