Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0017  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)  P0018  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)  P0019  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC Code DTC Detection Condition Trouble Area
P0016 Deviation in the crankshaft position sensor signal and VVT sensor (for Intake side of Bank 1) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft oil control valve (OCV) (for intake side of bank 1)

·

Camshaft timing gear assembly

·

ECM


P0017 Deviation in the crankshaft position sensor signal and VVT sensor (for Exhaust side of Bank 1) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for exhaust side of bank 1)

·

Camshaft timing exhaust gear assembly

·

ECM


P0018 Deviation in the crankshaft position sensor signal and VVT sensor (for Intake side of Bank 2) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for intake side of bank 2)

·

Camshaft timing gear assembly

·

ECM


P0019 Deviation in the crankshaft position sensor signal and VVT sensor (for Exhaust side of Bank 2) signal (2 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for exhaust side of bank 2)

·

Camshaft timing exhaust gear assembly

·

ECM



MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (Bank 1) or P0018 (Bank 2).

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0017 (Bank 1) or P0019 (Bank 2).

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
P0016, P0017, P0018 or P0019 is output A
P0016, P0017, P0018 or P0019 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the A/C on.


d.

Turn the tester on


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.


g.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.




OK

3.ADJUST VALVE TIMING

NG

4.INSPECT CAMSHAFT OIL CONTROL VALVE (FOR INTAKE SIDE OR EXHAUST SIDE)
3.ADJUST VALVE TIMING

NEXT

6.CONFIRM WHETHER DTC OUTPUT RECURS
4.INSPECT CAMSHAFT OIL CONTROL VALVE (FOR INTAKE SIDE OR EXHAUST SIDE)

OK

5.REPLACE CAMSHAFT TIMING GEAR OR CAMSHAFT TIMING EXHAUST GEAR

NG

5.REPLACE CAMSHAFT TIMING GEAR OR CAMSHAFT TIMING EXHAUST GEAR
a.

b.

Replace the camshaft timing exhaust gear (See page Engine / Hybrid System>3UR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

6.CONFIRM WHETHER DTC OUTPUT RECURS
6.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the tester (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>CHECK MODE PROCEDURE).


f.

Drive the vehicle in an urban area for approximately 10 minutes.


g.

Read DTCs using the tester.

OK:

No DTC is output.




OK

END

NG