Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255050 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.


A163193E02
1.889,2.238 3.144,2.426 1.254,0.188 10 24.5 mm (0.965 in.) 1.594,2.951 2.787,3.139 1.193,0.188 10 40 mm (1.58 in.) 1.883,2.538 3.061,2.726 1.178,0.188 10 14 mm (0.551 in.) 1.316,2.8 1.717,2.33 1.717,2.33 1.85,2.33 false 1.316,3.153 1.746,2.639 1.746,2.639 1.861,2.639 false

a.

Install the timing chain cover stud bolt.

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.
A178526E04
2.281,3.813 2.448,3.958 2.448,3.958 2.448,4.063 false 1.917,3.031 2.063,3.031 2.063,3.031 2.281,3.49 true 0.656,3.76 0.802,3.823 false 0.656,3.417 0.802,3.479 0.802,3.479 0.802,4.01 false 1.427,0.094 1.573,0.281 0.146,0.188 10 false A 0.167,1.177 0.313,1.365 0.146,0.188 10 false A 2.125,2.188 2.302,2.396 0.177,0.208 10 false B 0.271,4.021 1.417,4.219 1.146,0.198 10 false 9 mm (0.354 in.) 0.969,3.292 1.677,3.729 0.708,0.438 10 false 19 mm (0.748 in.) 1.917,4.052 3.063,4.25 1.146,0.198 10 false 12 mm (0.472 in.) 0.781,2.938 1.958,3.198 1.177,0.26 10 false 22 mm (0.866 in.) 2.615,3.344 3.271,3.74 0.656,0.396 10 false 39 mm (1.54 in.) 0.271,2.573 0.469,2.771 0.198,0.198 10 false A: 1.896,2.573 2.063,2.771 0.167,0.198 10 false B:

Install the oil pan stud bolt.

i.

Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 2.INSTALL RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


A160726E05
0.365,1.438 0.5,1.604 0.135,0.167 10 false A 0.573,1.927 0.708,2.094 0.135,0.167 10 false A 2.781,1.427 2.906,1.594 0.125,0.167 10 false B 2.813,1.823 2.938,1.99 0.125,0.167 10 false B 1.156,2.396 1.354,2.594 0.198,0.198 10 false *a 2.573,2.375 2.771,2.552 0.198,0.177 10 false *b 0.208,2.323 0.385,2.49 0.177,0.167 10 false A: 1.667,2.323 1.823,2.49 0.156,0.167 10 false B:

a.

Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard Protrusion:
Item Ring Pin Diameter Specified Condition
Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)
Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)


Text in Illustration
*a 7.5 to 8.5 mm
*b 3.6 to 4.6 mm


Hide 11381A 3.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A148433E02
0.067,0.812 0.434,1.054 0.367,0.242 10 SST 0.708,0.89 0.708,1.494 0.708,1.494 1.029,1.494 false 0.455,0.89 1.142,0.89 false

Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the oil seal at an angle.




Hide 12109A 4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the drain pipe.


c.

Install the oil drain pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381 5.INSTALL ENGINE REAR OIL SEAL RETAINER

A148434E16
0.896,0.531 1,0.094 1,0.094 1.146,0.094 false 0.365,1.708 0.365,1.458 false 3.052,1.75 3.052,1.469 false 1.188,0.031 1.396,0.229 0.208,0.198 10 false *a 2.823,1.75 3.313,1.927 0.49,0.177 10 false 3.5 mm 0.125,1.708 0.615,1.885 0.49,0.177 10 false 3.5 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Application position from inside edge of retainer:

3.5 mm (0.138 in.)


Text in Illustration
*a 2.0 to 3.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




b.

Install the oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.




Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil strainer.


c.

Install the oil strainer with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the O-ring is not twisted or damaged.



Hide 12121 7.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.

Install the baffle plate with the 7 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12101 8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

A160729E03
1.147,0.054 1.437,0.258 0.290,0.205 10 *a 0.721,0.768 0.938,0.14 0.938,0.14 1.095,0.14 false

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*a 3.0 to 4.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A237028E02
3.083,1.073 3.219,1.229 0.135,0.156 10 false A 3.083,0.708 3.219,0.865 0.135,0.156 10 false A 1.875,1.833 2.01,1.99 0.135,0.156 10 true B 1.479,1.844 1.615,2 0.135,0.156 10 true B 1.177,1.844 1.313,2 0.135,0.156 10 true B 0.896,1.802 1.031,1.958 0.135,0.156 10 true B 0.302,1.469 0.438,1.625 0.135,0.156 10 false B 2.979,0.271 3.115,0.427 0.135,0.156 10 false B 2.208,0.031 2.344,0.188 0.135,0.156 10 false B 1.875,0.031 2.01,0.188 0.135,0.156 10 false B 1.427,0.042 1.563,0.198 0.135,0.156 10 false B 0.969,0.042 1.104,0.198 0.135,0.156 10 false B 0.292,0.271 0.427,0.427 0.135,0.156 10 false B 2.313,1.76 2.448,1.917 0.135,0.156 10 true B

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing.


Standard Bolt:
Item Length Thread Diameter
Bolt A 92 mm (3.62 in.) 6 mm (0.236 in.)
Bolt B 30 mm (1.18 in.) 10 mm (0.394 in.)



Hide 12102A 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

A160730E02
1.515,0.119 1.720,0.314 0.205,0.195 10 *a 1.493,0.213 1.132,0.213 1.132,0.213 0.887,0.866 false

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*a 3.0 to 4.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A237027

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 16877 10.INSTALL NO. 1 HEAT EXCHANGER COVER

A161918E02
2.209,0.106 2.409,0.320 0.200,0.214 10 *a 2.18,0.205 1.951,0.205 1.951,0.205 1.613,0.551 false

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*a 3.0 to 4.0 mm

NOTICE:
·

Remove any oil from the contact surface.

·

Install the heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A237026E02
0.76,0.208 0.896,0.375 0.135,0.167 10 true A 0.479,1.427 0.615,1.594 0.135,0.167 10 true B 3.156,1.563 3.292,1.729 0.135,0.167 10 true C 1.177,0.104 1.313,0.271 0.135,0.167 10 true A 1.719,0.094 1.854,0.26 0.135,0.167 10 true A 2.115,0.083 2.25,0.25 0.135,0.167 10 true A 2.583,0.125 2.719,0.292 0.135,0.167 10 true A 2.979,0.323 3.115,0.49 0.135,0.167 10 true A 1.052,1.875 1.188,2.042 0.135,0.167 10 true A 1.625,1.875 1.76,2.042 0.135,0.167 10 true A 1.979,1.875 2.115,2.042 0.135,0.167 10 true A 3.281,0.969 3.417,1.135 0.135,0.167 10 false A

Install the heat exchanger cover with the 12 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing.


Standard Bolt:
Item Length Thread Diameter
Bolt A 20 mm (0.787 in.) 8 mm (0.315 in.)
Bolt B 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt C 16 mm (0.630 in.) 6 mm (0.236 in.)



Hide 12203A 11.INSTALL VENTILATION PIPE GASKET

A163596E06
1.125,1.292 1.125,1.5 1.125,1.5 1.333,1.5 false 0.885,1.292 1.365,1.292 false 0.51,1.208 0.896,1.406 0.385,0.198 10 true SST

a.

Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the gasket at an angle.

·

Do not tap the gasket excessively.




Hide 11445 12.INSTALL CYLINDER BLOCK WATER JACKET SPACER

A161997E05
0.162,0.115 0.338,0.295 0.176,0.180 10 *a 0.374,0.204 1.315,0.204 1.315,0.204 2.512,0.73 false 0.768,0.934 0.768,0.204 false

a.

Install the 2 water jacket spacers as shown in the illustration.

Text in Illustration
*a UP Mark

HINT:
·

Face the cutouts indicated by the arrows in illustration away from the engine.

·

Face the "UP" mark as shown in the illustration.




Hide 13716 15.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 32 valve stem caps to the cylinder heads.


Hide 13750 16.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the valve lash adjuster before installing it (See page Engine / Hybrid System>3UR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


b.

Install the 32 valve lash adjusters to the cylinder heads.

NOTICE:

Install the lash adjuster to the same place it was removed from.



Hide 13801 17.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the lash adjuster tips and valve stem cap ends.


b.
A386787E02
0.396,1.021 0.625,1.021 0.625,1.021 1.031,1.094 false 2.094,0.188 1.865,0.188 1.865,0.188 1.615,0.396 false 2.458,1.125 2.833,1.125 true 2.146,0.094 2.375,0.302 0.229,0.208 10 false *1 2.854,1.031 3.083,1.25 0.229,0.219 10 false *3 0.188,0.938 0.396,1.146 0.208,0.208 10 false *2

Install the 32 valve rocker arms as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


Hide 11103C 19.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 11104A 21.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13521A 22.INSTALL CRANKSHAFT TIMING GEAR KEY

A164296

a.

Install the timing gear key.

HINT:

The other timing gear key will be installed at a later step.



Hide 23.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft so that the timing gear key is as shown in the illustration. Then using a wrench, rotate each camshaft so that the timing marks are as shown in the illustration.

NOTICE:

When the crankshaft or a camshaft is rotated excessively, the valves and pistons may interfere with each other.



c.

Remove the crankshaft pulley bolt.

A178525E04
3.781,3.604 4.031,3.333 4.031,3.333 4.146,3.333 false 1.219,0.594 1.396,0.594 1.396,0.594 1.792,1.313 false 0.458,1.615 0.875,2.073 0.875,2.073 1.208,1.688 false 5.708,1.792 6.24,2.115 6.24,2.115 6.458,1.656 false 5.438,1.281 5.74,0.615 5.74,0.615 5.875,0.615 false 4.167,3.26 4.396,3.448 0.229,0.188 10 false *4 1.021,0.51 1.219,0.719 0.198,0.208 10 false *a 5.906,0.552 6.135,0.74 0.229,0.188 10 false *a 0.771,2.104 0.99,2.271 0.219,0.167 10 false *3 6.188,2.146 6.406,2.344 0.219,0.198 10 false *3 3.469,0.458 3.656,0.656 0.188,0.198 10 false *a 1.417,1.219 1.635,1.406 0.219,0.188 10 false *1 0.563,1.24 0.771,1.427 0.208,0.188 10 false *2 5.667,1.188 5.865,1.375 0.198,0.188 10 false *1 6.438,1.188 6.635,1.375 0.198,0.188 10 false *2

Text in Illustration
*1 IN *2 EX
*3 Knock Pin *4 Key
*a Toward Ceiling - -


Hide 13550 24.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

A148228E11
2.323,0.833 2.625,1.125 0.302,0.292 1.469,2.698 1.469,2.906 false 2.063,2.635 2.802,2.635 false 2.802,1.708 2.802,2.885 false 2.365,0.875 2.719,1.063 0.354,0.188 10 false *a 2.698,2.927 2.906,3.094 0.208,0.167 10 false *2 1.385,2.938 1.573,3.125 0.188,0.188 10 false *1

a.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Plunger
*2 Pin
*a Push


b.

While raising up the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 25.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH

a.
A198566E08
1.76,0.229 1.958,0.229 1.958,0.229 2.365,0.615 false 2.354,0.708 2.354,1.208 false 1.531,0.156 1.708,0.375 0.177,0.219 10 false *1 2.313,1.229 2.604,1.573 0.292,0.344 10 true *2

Align the No. 1 chain orange mark plate with the camshaft timing gear timing mark, and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark


b.
A149461E14
1.938,1.854 2.323,1.698 2.323,1.698 2.469,1.698 false 1.031,1.417 1.188,1.417 1.188,1.417 1.917,1.76 false 0.802,1.354 1.01,1.552 0.208,0.198 10 false *2 2.521,1.615 2.74,1.802 0.219,0.188 10 false *1

Align the No. 1 chain orange mark plate with the crankshaft timing sprocket timing mark, and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark


c.
A160663E13
0.865,0.76 1.167,0.135 1.167,0.135 1.646,0.135 false 1.938,0.135 2.49,0.135 2.49,0.135 2.719,0.813 false 0.885,1.802 2.75,1.802 2.75,1.802 2.75,1.125 false 0.885,1.115 0.885,1.906 false 1.708,0.052 1.906,0.25 0.198,0.198 10 false *2 0.771,1.927 1.042,2.156 0.271,0.229 10 true *1

Align the No. 2 chain yellow mark plates with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark

NOTICE:

The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.


HINT:

The crankshaft timing sprocket RH and camshaft timing exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket RH to the crankshaft.


e.

Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.


g.

Remove the pin from the No. 2 chain tensioner.


h.

Using a wrench to hold the hexagonal portion of the No. 1 camshaft, temporarily install the bolt.


i.

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, temporarily install the bolt.


Hide 13561 26.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

a.

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 27.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper.


Hide 13540 28.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

A148260E10
1.188,0.51 1.521,0.51 1.521,0.51 2.031,0.969 false 1.344,1.406 1.344,0.51 false 1.813,1.677 2.677,1.677 false 2.385,1.052 2.385,1.677 false 2.74,1.594 2.948,1.781 0.208,0.188 10 false *2 0.948,0.438 1.135,0.635 0.188,0.198 10 false *1

a.

Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.

Text in Illustration
*1 Stopper Plate
*2 Plunger


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the chain tensioner.


Hide 13560A 29.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

A148227E10
2.135,1.76 2.01,1.76 2.01,1.76 1.813,2.219 false 1.188,2.51 1.375,2.51 1.375,2.51 2.021,2.354 false 2.552,0.344 2.802,0.594 0.25,0.25 10 true *a 2.177,1.677 2.417,1.844 0.24,0.167 10 false *2 0.979,2.417 1.156,2.604 0.177,0.188 10 false *1

a.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Plunger
*2 Pin
*a Push


b.

While pushing down the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 30.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH

a.
A198567E08
1.094,0.656 1.406,0.188 1.406,0.188 1.604,0.188 false 1.104,0.74 1.104,1.167 false 1.646,0.104 1.823,0.302 0.177,0.198 10 false *1 1,1.188 1.333,1.417 0.333,0.229 10 true *2

Align the No. 1 chain orange mark plate with the camshaft timing gear timing mark, and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark


b.
A149462E16
2.469,1.49 2.333,1.49 2.333,1.49 1.708,1.719 false 1.688,1.5 1.198,1.333 1.198,1.333 1.052,1.333 false 0.802,1.25 1.01,1.448 0.208,0.198 10 false *2 2.5,1.406 2.708,1.594 0.208,0.188 10 false *1

Align the No. 1 chain orange mark plate with the crankshaft timing sprocket timing mark, and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark


c.
A160666E12
0.823,0.792 0.99,0.125 0.99,0.125 1.438,0.125 false 1.771,0.125 2.281,0.125 2.281,0.125 2.479,0.677 false 0.792,1.104 0.792,1.896 false 0.792,1.792 2.458,1.792 2.458,1.792 2.458,1 false 1.51,0.021 1.719,0.198 0.208,0.177 10 false *2 0.677,1.906 0.865,2.083 0.188,0.177 10 true *1

Align the No. 2 chain yellow mark plates with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.

Text in Illustration
*1 Mark Plate
*2 Timing Mark

NOTICE:

The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.


HINT:

The crankshaft timing sprocket LH and camshaft timing exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket LH to the crankshaft.


e.

Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear.

NOTICE:

Because the timing mark positions of the gears may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.



g.

Remove the pin from the No. 3 chain tensioner.


h.

Using a wrench to hold the hexagonal portion of the No. 3 camshaft, temporarily install the bolt.


i.

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, temporarily install the bolt.


Hide 13559 31.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH

A178487

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and install the chain tensioner slipper.


Hide 13540 32.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

A148260E06
2.712,1.388 2.965,1.591 0.253,0.204 10 *2 0.945,0.592 1.117,0.759 0.171,0.167 10 *1 2.425,1.1 2.682,1.467 2.682,1.467 1.951,1.72 false 1.996,0.979 1.174,0.693 1.174,0.693 1.361,1.403 false

a.

Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.

Text in Illustration
*1 Stopper Plate
*2 Plunger


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13561 33.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

A178533

a.

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Remove the hexagon wrench from the No. 1 chain tensioner.


Hide 13050 34.TIGHTEN CAMSHAFT TIMING GEAR

a.
A161993E07
2.969,0.042 3.323,0.365 0.354,0.323 10 true *a

for Bank 1:

i.

Using a wrench, hold the hexagonal portion of the No. 3 camshaft.

Text in Illustration
*a Hold
V100135

Turn


ii.

Tighten the bolt of the camshaft timing gear.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


iii.
A161994E06
3.063,0.583 3.385,0.729 0.323,0.146 10 false *a

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the bolt of the camshaft timing exhaust gear.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn



b.
A161995E06
1.208,0.031 1.563,0.24 0.354,0.208 10 false *a

for Bank 2:

i.

Using a wrench, hold the hexagonal portion of the No. 1 camshaft.

Text in Illustration
*a Hold
V100135

Turn


ii.

Tighten the bolt of the camshaft timing gear.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


iii.
A161996E06
0.865,0.083 1.063,0.271 0.198,0.188 10 false *a

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the bolt of the camshaft timing exhaust gear.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn



Hide 35.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.


c.

Remove the crankshaft pulley bolt.

A160654E10
3.49,4.813 4.021,5.052 4.021,5.052 4.021,5.167 false 3.646,4.396 4.042,4.01 4.042,4.01 4.167,4.01 false 0.958,0.292 0.448,0.292 0.448,0.292 0.552,0.875 true 1.219,0.302 1.719,0.302 1.719,0.302 1.667,0.76 true 5.927,0.333 5.479,0.333 5.479,0.333 5.552,0.823 true 6.188,0.333 6.76,0.333 6.76,0.333 6.698,0.948 true 0.542,5.625 0.813,6.167 0.813,6.167 1.354,5.625 false 0.333,4.448 0.229,4.448 0.229,4.448 0.531,5.385 false 0.531,3.365 1.042,4.073 1.042,4.073 1.375,3.458 false 5.823,5.625 6.083,6.198 6.083,6.198 6.552,5.615 false 5.323,4.656 5.073,4.656 5.073,4.656 5.542,5.26 false 6.344,4.458 6.854,4.458 6.854,4.458 6.594,5.385 false 5.458,3.698 5.979,4.115 5.979,4.115 6.448,3.49 false 0.594,3.208 0.344,2.375 0.344,2.375 1.021,2.375 true 1.74,3.198 2.042,2.375 2.042,2.375 1.281,2.375 true 5.406,3.24 5.167,2.458 5.167,2.458 5.885,2.458 true 6.552,3.292 6.865,2.469 6.865,2.469 6.125,2.469 true 1.667,5.271 2.083,4.698 2.083,4.698 1.99,4.698 false 1.813,5.302 1.99,5.51 1.99,5.51 1.99,5.781 false 5.396,5.292 5.292,5.438 5.292,5.438 5.292,5.667 false 1.396,5.385 1.5,4.896 1.5,4.896 1.302,4.896 false 5.844,4.906 5.656,4.906 5.656,4.906 5.792,5.385 false 1,0.229 1.208,0.406 0.208,0.177 10 false *1 0.708,6.198 0.927,6.396 0.219,0.198 10 false *2 0.969,4.094 1.156,4.271 0.188,0.177 10 false *3 5.354,4.583 5.521,4.771 0.167,0.188 10 false *c 5.875,4.833 6.031,5.01 0.156,0.177 10 false *f 6,6.219 6.177,6.396 0.177,0.177 10 false *2 5.906,4.125 6.146,4.302 0.24,0.177 10 true *3 0.365,4.375 0.594,4.552 0.229,0.177 10 false *b 1.125,4.813 1.313,5 0.188,0.188 10 false *d 1.813,4.625 1.979,4.802 0.167,0.177 10 true *c 6.167,4.375 6.354,4.573 0.188,0.198 10 false *e 3.469,1.198 3.698,1.406 0.229,0.208 10 false *a 5.99,0.26 6.198,0.438 0.208,0.177 10 false *1 1.083,2.292 1.292,2.469 0.208,0.177 10 false *2 5.938,2.375 6.146,2.552 0.208,0.177 10 false *2 1.896,5.802 2.125,6.01 0.229,0.208 10 false *a 5.208,5.646 5.438,5.854 0.229,0.208 10 false *a 3.927,5.198 4.135,5.375 0.208,0.177 10 false *1 4.188,3.938 4.396,4.115 0.208,0.177 10 false *4

Text in Illustration
*1 Timing Mark *2 Timing Mark Position
*3 Knock Pin Position *4 Key
*a Toward Ceiling *b Approximately 2°
*c Approximately 45° *d Approximately 16°
*e Approximately 18° *f Approximately 32°


Hide 11302 37.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11193 42.INSTALL SPARK PLUG TUBE GASKET

a.
A385341

Using a cutter knife, cut off the seal part of the removed gasket.

Text in Illustration
V100155

Area to cut off


b.
A164316E06
1.167,0.594 1.271,0.344 1.271,0.344 1.396,0.344 false 1.688,1.146 1.688,1.5 false 1.427,0.26 1.667,0.458 0.24,0.198 10 false *1 1.604,1.521 1.802,1.708 0.198,0.188 10 false *2

Using the removed gasket and a hammer, tap in a new gasket until it stops.

Text in Illustration
*1 Removed Gasket
*2 New Gasket

HINT:

If the removed gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the lip of the gasket.


d.

Return the 4 ventilation baffle plate claws to the original positions.


Hide 15678A 43.INSTALL OIL CONTROL VALVE FILTER

a.
A164313E16
2.49,0.885 2.49,1.292 false 2.813,0.125 2.969,0.125 2.969,0.125 3.125,0.906 true 1.708,0.417 2.167,0.417 2.167,0.417 2.813,0.802 true 2.385,1.302 2.563,1.469 0.177,0.167 10 false *3 1.479,0.302 1.771,0.531 0.292,0.229 10 true *2 2.615,0.042 2.781,0.219 0.167,0.177 10 true *1

LH:

i.

Install the filter in the cylinder head.

Text in Illustration
*1 Cylinder Head Cover Spacer
*2 Gasket
*3 Filter


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A164314E13
0.917,0.792 0.917,1.219 false 0.292,0.781 0.646,0.104 0.646,0.104 0.781,0.104 true 0.625,0.688 0.99,0.417 0.99,0.417 1.917,0.417 true 0.813,1.24 0.99,1.417 0.177,0.177 10 false *3 1.948,0.333 2.198,0.583 0.25,0.25 10 true *2 0.802,0 1.021,0.219 0.219,0.219 10 true *1

RH:

i.

Install the filter in the cylinder head.

Text in Illustration
*1 Cylinder Head Cover Spacer
*2 Gasket
*3 Filter


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 11201 44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11202 45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 16603 46.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 15330B 48.INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY

a.

for Bank 1:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

for Bank 2:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 11401G 50.INSTALL CRANKSHAFT POSITION SENSOR

a.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19312 51.INSTALL CRANK POSITION SENSOR PROTECTOR

a.

Install the sensor protector with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 52.INSTALL CAMSHAFT POSITION SENSOR

a.

Install the camshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 53.INSTALL VVT SENSOR

a.

for Bank 1:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

for Bank 2:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 19100P 54.INSTALL SPARK PLUG

a.

Using a 16 mm plug wrench, install the 8 spark plugs.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12185 55.INSTALL OIL FILLER CAP HOUSING

a.
A161917

Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.


b.

Install the cap housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 56.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 83520 60.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY