Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) J

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E48
0.979,0.844 2.844,1.167 1.865,0.323 10 false from EFI MAIN NO. 1 Fuse 0.938,1.208 2.656,1.469 1.719,0.26 10 false from EFI MAIN NO. 1 Relay 0.25,1.813 2.698,2.427 2.448,0.615 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.208,2.76 2.635,3.323 2.427,0.563 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.927,3.083 5.333,3.448 0.406,0.365 10 false ECM 2.875,0.74 3.26,0.885 0.385,0.146 10 false BATT 2.823,1.083 3.448,1.292 0.625,0.208 10 false +B, +B2 3.01,1.99 3.292,2.177 0.281,0.188 10 false VC 4.396,0.896 6.188,1.25 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.792 6.354,2.146 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

WIRING DIAGRAM


A351216E03
5.692,0.931 6.193,1.132 0.501,0.201 10 VCNE 5.404,0.927 5.733,1.139 0.330,0.211 10 64 5.692,1.435 6.010,1.591 0.318,0.156 10 NE+ 5.404,1.331 5.657,1.514 0.253,0.184 10 66 5.404,1.751 5.657,1.942 0.253,0.191 10 65 5.692,1.838 5.987,1.994 0.295,0.156 10 NE- 5.404,2.463 5.636,2.661 0.232,0.198 10 89 5.692,2.554 5.987,2.710 0.295,0.156 10 G2+ 5.407,3.603 5.635,3.801 0.228,0.199 10 67 5.692,3.697 6.091,3.853 0.399,0.156 10 VV1+ 5.407,4.021 5.663,4.221 0.256,0.201 10 88 5.692,4.101 6.091,4.257 0.399,0.156 10 VV1- 5.407,4.713 5.656,4.908 0.249,0.195 10 90 5.692,4.794 6.091,4.949 0.399,0.156 10 EV1+ 6.125,8.47 6.462,8.621 0.336,0.151 10 ECM 2.938,0.934 3.048,1.090 0.110,0.156 10 3 2.938,1.351 3.048,1.506 0.110,0.156 10 1 2.941,1.758 3.060,1.922 0.119,0.164 10 2 0.222,0.998 0.619,1.191 0.397,0.193 10 C114 0.222,1.17 1.966,1.344 1.744,0.174 10 Crankshaft Position Sensor 0.217,2.326 0.620,2.533 0.404,0.207 10 C99 0.217,2.49 2.007,2.701 1.790,0.211 10 Camshaft Position Sensor 2.601,2.349 2.826,2.505 0.225,0.156 10 VC 2.609,1.019 2.834,1.175 0.225,0.156 10 VC 2.605,2.555 2.826,2.711 0.220,0.156 10 G2 2.633,2.978 2.845,3.143 0.211,0.165 10 G- 2.925,2.264 3.030,2.415 0.105,0.151 10 3 2.925,2.474 3.030,2.625 0.105,0.151 10 1 2.925,2.896 3.030,3.048 0.105,0.151 10 2 2.605,3.483 2.830,3.639 0.225,0.156 10 VC 2.441,3.69 2.828,3.845 0.387,0.156 10 VVL+ 2.483,4.097 2.851,4.262 0.369,0.165 10 VVL- 2.929,3.394 3.034,3.545 0.105,0.151 10 3 2.929,3.604 3.034,3.755 0.105,0.151 10 1 2.929,4.027 3.034,4.178 0.105,0.151 10 2 0.208,3.45 0.555,3.640 0.347,0.190 10 C26 0.208,3.623 1.971,3.950 1.762,0.327 10 VVT Sensor (for Intake Side of Bank 1) 2.52,4.597 2.833,4.753 0.313,0.156 10 VC2 2.525,4.803 2.833,4.959 0.308,0.156 10 EX+ 2.548,5.226 2.852,5.391 0.304,0.165 10 EX- 2.925,4.504 3.030,4.655 0.105,0.151 10 3 2.925,4.714 3.030,4.865 0.105,0.151 10 1 2.925,5.137 3.030,5.288 0.105,0.151 10 2 0.208,4.56 0.659,4.747 0.451,0.187 10 C121 0.208,4.733 2.100,5.060 1.892,0.327 10 VVT Sensor (for Exhaust Side of Bank 1) 6.131,8.313 6.509,8.503 0.378,0.191 10 C45 2.517,1.434 2.846,1.596 0.330,0.163 10 NE+ 2.517,1.854 2.846,2.017 0.330,0.163 10 NE- 5.692,5.916 6.063,6.072 0.371,0.156 10 VV2+ 5.692,6.35 6.063,6.506 0.371,0.156 10 VV2- 5.333,5.851 5.614,6.031 0.281,0.180 10 112 5.333,6.261 5.614,6.448 0.281,0.187 10 111 5.692,7.083 6.063,7.238 0.371,0.156 10 EV2+ 5.333,6.99 5.621,7.205 0.288,0.215 10 113 0.218,5.706 0.590,5.896 0.373,0.190 10 C25 0.218,5.884 1.989,6.229 1.772,0.346 10 VVT Sensor (for Intake Side of Bank 2) 2.601,5.735 2.826,5.891 0.225,0.156 10 VC 2.416,5.949 2.822,6.105 0.406,0.156 10 VVR+ 2.416,6.348 2.822,6.504 0.406,0.156 10 VVR- 2.926,5.651 3.045,5.807 0.119,0.156 10 3 2.926,5.856 3.045,6.012 0.119,0.156 10 1 2.926,6.263 3.045,6.419 0.119,0.156 10 2 0.218,6.827 0.694,7.030 0.477,0.204 10 C122 0.218,7.004 2.104,7.350 1.887,0.346 10 VVT Sensor (for Exhaust Side of Bank 2) 2.51,6.871 2.825,7.027 0.315,0.156 10 VC2 2.51,7.09 2.823,7.245 0.313,0.156 10 EX+ 2.533,7.485 2.823,7.641 0.290,0.156 10 EX- 2.926,6.772 3.045,6.927 0.119,0.156 10 3 2.926,6.977 3.045,7.133 0.119,0.156 10 1 2.926,7.391 3.045,7.547 0.119,0.156 10 2 4.631,8.198 4.802,8.407 0.171,0.209 10 A 5.692,2.262 6.193,2.463 0.501,0.201 10 VCV2 5.348,2.258 5.677,2.449 0.330,0.191 10 110 5.683,5.643 6.184,5.844 0.501,0.201 10 VCV1 5.394,5.64 5.724,5.830 0.330,0.191 10 87

A375094E03
5.667,1.927 6.167,2.115 0.5,0.188 10 false VCAI 6.156,7.24 6.5,7.417 0.344,0.177 10 false C45 5.385,1.917 5.604,2.073 0.219,0.156 10 false 75 5.667,2.396 5.979,2.583 0.313,0.188 10 false AIP 5.375,2.292 5.604,2.458 0.229,0.167 10 false 73 5.667,3.646 6.083,3.844 0.417,0.198 10 false AIP2 5.406,3.542 5.635,3.719 0.229,0.177 10 false 72 5.667,4.167 6.125,4.365 0.458,0.198 10 false EAIP 5.406,3.948 5.646,4.115 0.24,0.167 10 false 74 0.24,1.979 0.667,2.177 0.427,0.198 10 false C137 0.229,2.156 2.208,2.333 1.979,0.177 10 false Air Switching Valve (for Bank 1) 0.219,3.271 0.625,3.469 0.406,0.198 10 false C138 0.219,3.427 2.198,3.604 1.979,0.177 10 false Air Switching Valve (for Bank 2) 2.594,2.021 2.823,2.177 0.229,0.156 10 false VC 2.906,1.938 3.021,2.094 0.115,0.156 10 false 2 2.906,2.292 3.021,2.448 0.115,0.156 10 false 3 2.563,2.375 2.833,2.531 0.271,0.156 10 false AIP 2.615,2.75 2.813,2.906 0.198,0.156 10 false E2 2.906,2.667 3.021,2.833 0.115,0.167 10 false 4 2.51,3.292 2.813,3.448 0.302,0.156 10 false VC2 2.906,3.208 3.021,3.365 0.115,0.156 10 false 2 2.906,3.552 3.021,3.708 0.115,0.156 10 false 3 2.479,3.646 2.823,3.802 0.344,0.156 10 false AIP2 2.542,4.052 2.813,4.208 0.271,0.156 10 false E22 2.906,3.958 3.021,4.125 0.115,0.167 10 false 4 5.667,5 5.969,5.156 0.302,0.156 10 false PSP 5.385,4.906 5.594,5.083 0.208,0.177 10 false 76 0.229,4.625 0.521,4.781 0.292,0.156 10 false C59 0.24,4.792 1.438,5.115 1.198,0.323 10 false Power Steering Oil Pressure Sensor 2.594,4.635 2.823,4.802 0.229,0.167 10 false VC 2.5,5.01 2.813,5.167 0.313,0.156 10 false PSP 2.615,5.385 2.823,5.542 0.208,0.156 10 false E2 2.906,4.552 3.021,4.708 0.115,0.156 10 false 1 2.906,4.927 3.021,5.083 0.115,0.156 10 false 2 2.906,5.302 3.021,5.458 0.115,0.156 10 false 3 4.5,0.375 4.646,0.51 0.146,0.135 10 false A 6.156,7.406 6.5,7.563 0.344,0.156 10 false ECM

A351218E06
6.135,6.344 6.521,6.531 0.385,0.188 10 false ECM 5.302,0.792 5.583,0.948 0.281,0.156 10 false 125 5.667,0.885 6.063,1.042 0.396,0.156 10 false VCTA 5.302,1 5.698,1.177 0.396,0.177 10 false C45 5.302,1.281 5.583,1.438 0.281,0.156 10 false 126 5.302,1.49 5.698,1.677 0.396,0.188 10 false C45 5.302,1.75 5.583,1.906 0.281,0.156 10 false 101 5.302,1.969 5.688,2.177 0.385,0.208 10 false C45 5.302,2.219 5.583,2.375 0.281,0.156 10 false 124 5.302,2.448 5.771,2.688 0.469,0.24 10 false C45 5.667,1.458 6.052,1.604 0.385,0.146 10 false VTA1 5.667,1.927 6.052,2.073 0.385,0.146 10 false VTA2 5.667,2.323 5.979,2.469 0.313,0.146 10 false ETA 5.344,3.208 5.625,3.354 0.281,0.146 10 false 55 5.302,3.438 5.573,3.583 0.271,0.146 10 false A38 5.344,3.646 5.625,3.792 0.281,0.146 10 false 58 5.313,3.865 5.729,4.094 0.417,0.229 10 false A38 5.344,4.083 5.625,4.229 0.281,0.146 10 false 53 5.302,4.302 5.708,4.531 0.406,0.229 10 false A38 5.344,4.51 5.625,4.656 0.281,0.146 10 false 56 5.302,4.74 5.698,4.969 0.396,0.229 10 false A38 5.344,4.948 5.625,5.094 0.281,0.146 10 false 54 5.302,5.177 5.719,5.406 0.417,0.229 10 false A38 5.344,5.385 5.625,5.531 0.281,0.146 10 false 57 5.302,5.615 5.667,5.833 0.365,0.219 10 false A38 5.667,3.292 6.073,3.448 0.406,0.156 10 false VCPA 5.667,4.25 5.979,4.406 0.313,0.156 10 false VPA 5.667,5.031 5.979,5.188 0.313,0.156 10 false EPA 5.667,4.688 6.042,4.844 0.375,0.156 10 false VPA2 5.667,5.479 6.042,5.635 0.375,0.156 10 false EPA2 5.667,3.74 6.073,3.896 0.406,0.156 10 false VCP2 0.271,0.948 0.5,1.104 0.229,0.156 10 false C3 0.271,1.115 1.875,1.354 1.604,0.24 10 false Throttle Position Sensor 2.604,0.969 2.844,1.125 0.24,0.156 10 false VC 2.521,1.458 2.833,1.615 0.313,0.156 10 false VTA 2.458,1.938 2.833,2.104 0.375,0.167 10 false VTA2 2.625,2.406 2.844,2.573 0.219,0.167 10 false E2 2.927,0.885 3.042,1.042 0.115,0.156 10 false 5 2.927,1.365 3.042,1.521 0.115,0.156 10 false 6 2.927,1.844 3.042,2 0.115,0.156 10 false 4 2.927,2.313 3.042,2.469 0.115,0.156 10 false 3 0.281,3.365 0.635,3.563 0.354,0.198 10 false A31 0.281,3.521 1.521,3.906 1.24,0.385 10 false Accelerator Pedal Position Sensor 2.427,3.396 2.844,3.542 0.417,0.146 10 false VCPA 2.427,3.833 2.844,3.979 0.417,0.146 10 false VCP2 2.51,4.26 2.833,4.406 0.323,0.146 10 false VPA 2.438,4.708 2.854,4.854 0.417,0.146 10 false VPA2 2.521,5.125 2.844,5.271 0.323,0.146 10 false EPA 2.448,5.573 2.865,5.719 0.417,0.146 10 false EPA2 2.927,3.302 3.042,3.458 0.115,0.156 10 false 4 2.927,3.74 3.042,3.896 0.115,0.156 10 false 1 2.927,4.167 3.042,4.323 0.115,0.156 10 false 6 2.927,4.604 3.042,4.76 0.115,0.156 10 false 3 2.927,5.052 3.042,5.208 0.115,0.156 10 false 5 2.927,5.479 3.042,5.635 0.115,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and GTS on.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A351229E01
0.34,0.658 0.634,0.865 0.295,0.207 10 *1 1.033,4.039 1.328,4.245 0.295,0.207 10 *2 0.483,2.824 1.107,4.004 false

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI No. 2 fuse) - Body ground Engine switch on (IG) 11 to 14 V


Text Illustration
*1 Engine Room Relay Block
*2 EFI No. 2 Fuse

HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (POWER STEERING OIL PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL POSITION SENSOR

5.CHECK CONNECTION BETWEEN GTS AND ECM (POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the power steering oil pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR)

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

7.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Intake Side of Bank 1)

B

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Intake Side of Bank 1)
a.

Disconnect the VVT sensor (for Intake Side of Bank 1) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Exhaust Side of Bank 1)

B

REPLACE VVT SENSOR (for Intake Side of Bank 1)

9.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Exhaust Side of Bank 1)
a.

Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Intake Side of Bank 2)

B

REPLACE VVT SENSOR (for Exhaust Side of Bank 1)

10.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Intake Side of Bank 2)
a.

Disconnect the VVT sensor (for Intake Side of Bank 2) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Exhaust Side of Bank 2)

B

REPLACE VVT SENSOR (for Intake Side of Bank 2)

11.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR for Exhaust Side of Bank 2)
a.

Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (AIR SWITCHING VALVE FOR BANK 1)

B

REPLACE VVT SENSOR (for Exhaust Side of Bank 2)

12.CHECK CONNECTION BETWEEN GTS AND ECM (AIR SWITCHING VALVE FOR BANK 1)
a.

Disconnect the air switching valve (for Bank 1) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

13.CHECK CONNECTION BETWEEN GTS AND ECM (AIR SWITCHING VALVE FOR BANK 2)

B

13.CHECK CONNECTION BETWEEN GTS AND ECM (AIR SWITCHING VALVE FOR BANK 2)
a.

Disconnect the air switching valve (for Bank 2) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

14.CHECK HARNESS AND CONNECTOR

B

14.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the power steering oil pressure sensor connector.


d.

Disconnect the camshaft position sensor connector.


e.

Disconnect the crankshaft position sensor connector.


f.

Disconnect the VVT sensor (for Intake Side of Bank 1) connector.


g.

Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.


h.

Disconnect the VVT sensor (for Intake Side of Bank 2) connector.


i.

Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.


j.

Disconnect the ECM connectors.


k.

Disconnect the No. 2 integration relay connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-125 (VCTA) - Body ground Always 10 kΩ or higher
A38-55 (VCPA) - Body ground Always 10 kΩ or higher
A38-58 (VCP2) - Body ground Always 10 kΩ or higher
C45-87 (VCV1) - Body ground Always 10 kΩ or higher
C45-110 (VCV2) - Body ground Always 10 kΩ or higher
C45-64 (VCNE) - Body ground Always 10 kΩ or higher
1S-11 - A38-2 (+B) Always Below 1 Ω
1S-11 - A38-3 (+B2) Always Below 1 Ω
1S-11 or A38-2 (+B) - Body ground Always 10 kΩ or higher
1S-11 or A38-3 (+B2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR