Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Tilt Sensor Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the tilt sensor (theft warning ultrasonic sensor) via the ISIF communication line. The tilt sensor (theft warning ultrasonic sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.

HINT:

In the following situations, the tilt sensor (theft warning ultrasonic sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.

·

The vehicle is transported by a ferry, trailer or train.

·

The vehicle is parked in a multi-story parking facility.

·

The vehicle is washed by an automatic car wash.

·

A tire blows out.

·

The vehicle is jacked up for a tire or wheel change.

·

An earthquake occurs or the road subsides.

·

Goods such as skis or snowboards are loaded or unloaded.



WIRING DIAGRAM

B373997E15
1.615,2.646 2.958,2.875 1.344,0.229 10 false Map Light Assembly 1.125,0.406 1.896,0.604 0.771,0.198 10 false from Battery 5,2.604 7.156,3 2.156,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 1.521,1.271 3.156,1.708 1.635,0.438 10 false Tilt Sensor (Theft Warning Ultrasonic Sensor) 1.604,2.479 2.375,2.677 0.771,0.198 10 false R7 0.917,1.552 1.646,1.74 0.729,0.188 10 false GND9 0.667,1.552 1.396,1.74 0.729,0.188 10 false 17 3.74,1.25 4.469,1.438 0.729,0.188 10 false +B2 3.719,1.823 4.448,2.01 0.729,0.188 10 false IOUT 4.083,1.24 4.813,1.427 0.729,0.188 10 false 15 4.115,1.802 4.844,1.99 0.729,0.188 10 false 12 5.396,1.813 6.125,2 0.729,0.188 10 false 12 5.625,1.813 6.354,2 0.729,0.188 10 false ISIF 5,2.438 5.771,2.635 0.771,0.198 10 false E117 2.896,0.583 3.885,0.813 0.99,0.229 10 false MPX-B NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure (See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION)



PROCEDURE

1.READ VALUE USING GTS (Intrusion Sensor)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

NOTICE:
B490800C01
1.188,1 1.458,0.271 1.458,0.271 1.552,0.271 true 2.292,0.99 2.563,0.26 2.563,0.26 2.656,0.26 true 1.188,1.167 1.375,1.583 1.375,1.583 1.469,1.583 true 2.26,1.177 2.448,1.594 2.448,1.594 2.542,1.594 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *1 1.604,0.188 1.917,0.344 0.313,0.156 10 false *a 1.521,1.521 1.833,1.677 0.313,0.156 10 false *b 2.688,0.188 3,0.344 0.313,0.156 10 false *a 2.583,1.531 2.896,1.688 0.313,0.156 10 false *b
*1 Map Light Assembly
*a Intrusion Sensor (Theft Warning Ultrasonic Sensor)
*b Tape


·

Be sure to cover the 2 intrusion sensors (theft warning ultrasonic sensor) in the map light assembly with tape to prevent detected by the intrusion sensor.

·

After setting the theft deterrent system, wait at least 30 seconds (until the vehicle is in the armed state), tilt the vehicle (jack up the vehicle so that the tires are in the air) and check the Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM (w/ Entry and Start System)>SYSTEM DESCRIPTION



HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Status of the tilt sensor detection ON or OFF ON: Change in pitch angle detected
OFF: Both of the conditions below is met
·

No moving object detected by sensor

·

Vehicle tilt not detected by sensor


-

OK:

The GTS display changes correctly in response to the detection condition of the tilt sensor (theft warning ultrasonic sensor).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TILT SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
2.CHECK TILT SENSOR (THEFT WARNING ULTRASONIC SENSOR) (IOUT)
a.

Using an oscilloscope, check the waveform.

U164404C01
2.333,2.656 2.448,2.708 false 1.813,2.656 1.917,2.708 false 2.333,1.365 3.156,0.969 false 3.448,0.125 3.802,0.292 0.354,0.167 10 false R7 1.917,1.302 2.677,1.479 0.76,0.177 10 false IOUT 3.969,3.177 4.729,3.354 0.76,0.177 10 false *e 3.969,2.583 4.729,2.76 0.76,0.177 10 false *d 2.042,3.188 2.802,3.365 0.76,0.177 10 false *f 2.521,3.188 3.281,3.365 0.76,0.177 10 false *g 2.604,3.542 3.365,3.719 0.76,0.177 10 false *d 2.167,2.594 2.927,2.771 0.76,0.177 10 false *c 1.646,2.594 2.406,2.771 0.76,0.177 10 false *b 1.469,4.073 2.229,4.25 0.76,0.177 10 false *i 3.979,4.073 4.74,4.25 0.76,0.177 10 false *j 1.073,2.906 1.833,3.083 0.76,0.177 10 false LO 1.073,2.448 1.833,2.625 0.76,0.177 10 false HI 0.99,0.24 1.75,0.417 0.76,0.177 10 false *a
*a Component with harness connected
(Map Light Assembly)
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Tester Connection Content
Tester Connection R7-12 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the tilt sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MAP LIGHT ASSEMBLY)
a.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-12 (ISIF) - R7-12 (IOUT) Always Below 1 Ω
E117-12 (ISIF) or R7-12 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the tilt sensor (theft warning ultrasonic sensor) from the map light assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL


c.
U164384E02
1.177,0.74 1.24,0.74 1.24,0.74 1.542,0.979 true 0.813,1.875 0.885,1.875 0.885,1.875 0.969,2.323 true 1.167,3.135 1.229,3.135 1.229,3.135 1.313,2.385 true 2.865,2.969 2.781,2.969 2.781,2.969 2.563,2.531 true 1.771,1.094 2.208,1.344 2.208,1.344 2.323,1.344 true 2.281,0.51 2.146,0.51 2.146,0.51 1.927,0.958 true 1.667,0.406 1.875,0.573 0.208,0.167 10 false A 1.677,1.729 1.885,1.896 0.208,0.167 10 false B 0.854,0.646 1.198,0.896 0.344,0.25 10 false +B2 0.844,3.063 1.271,3.313 0.427,0.25 10 false IOUT 0.531,1.792 0.875,2.042 0.344,0.25 10 false +B2 2.917,2.875 3.344,3.125 0.427,0.25 10 false GND9 2.365,1.271 2.708,1.521 0.344,0.25 10 false GND 2.333,0.427 2.813,0.729 0.479,0.302 10 false IOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) -B-17 (GND9) Always Below 1 Ω
A-2 (IOUT) -B-12 (IOUT) Always Below 1 Ω
A-4 (+B2) - B-15 (+B2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TILT SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG