The park/neutral position switch turns on when the shift lever is moved to R, causing the back-up lights to illuminate.
Remove the BK/UP LP fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BK/UP LP fuse | Always | Below 1 Ω |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for Automatic Transmission | A |
| for Manual Transmission | B |
A
B
Inspect the park/neutral position switch.
for AE80F Automatic Transmission: See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AB60F Automatic Transmission: See pageDrivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AC60F Automatic Transmission: See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for AB60F Automatic Transmission) | B |
| NG (for AE80F Automatic Transmission) | C |
| NG (for AC60F Automatic Transmission) | D |
A
B
(See pageDrivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
C
(See pageDrivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
D
(See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Disconnect the C24 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C24-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C24-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | except 3UR-FE |
| *B | for 3UR-FE |
| *a | Front view of wire harness connector
(to Mass Air Flow Meter) |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for Double Swing Out Type | A |
| except Double Swing Out Type | B |
A
B
Disconnect the C24 park/neutral position switch connector.
for LH:
Disconnect the O8 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-1 (RL) - O8-2 | Always | Below 1 Ω |
| O8-1 - Body ground | ||
| O8-2 - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the O7 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-1 (RL) - O7-2 | Always | Below 1 Ω |
| O7-1 - Body ground | ||
| O7-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the C24 park/neutral position switch connector.
for LH:
Disconnect the S34 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-1 (RL) - S34-3 (B) | Always | Below 1 Ω |
| S34-4 (E) - Body ground | ||
| S34-3 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-2 (RL) - S34-3 (B) | Always | Below 1 Ω |
| S34-4 (E) - Body ground | ||
| S34-3 (B) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the S35 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-1 (RL) - S35-3 (B) | Always | Below 1 Ω |
| S35-4 (E) - Body ground | ||
| S35-3 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-2 (RL) - S35-3 (B) | Always | Below 1 Ω |
| S35-4 (E) - Body ground | ||
| S35-3 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the back-up light switch (See page Drivetrain>H150F (MANUAL TRANSMISSION / TRANSAXLE)>BACK-UP LIGHT SWITCH>INSPECTION).
OK
NG
Disconnect the C39 back-up light switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C39-2 - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for Double Swing Out Type | A |
| except Double Swing Out Type | B |
A
B
Disconnect the C39 back-up light switch connector.
for LH:
Disconnect the O8 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-1 - O8-2 | Always | Below 1 Ω |
| O8-1 - Body ground | ||
| O8-2 - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the O7 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-1 - O7-2 | Always | Below 1 Ω |
| O7-1 - Body ground | ||
| O7-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the C39 back-up light switch connector.
for LH:
Disconnect the S34 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-1 - S34-3 (B) | Always | Below 1 Ω |
| S34-4 (E) - Body ground | ||
| S34-3 (B) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the S35 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-1 - S35-3 (B) | Always | Below 1 Ω |
| S35-4 (E) - Body ground | ||
| S35-3 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG