Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. DTC Detection Condition Trouble Area
B1247 In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

B281126E28
0.396,3.958 1.792,4.344 1.396,0.385 10 false Tire Pressure Warning ECU and Receiver 5.448,3.802 7.115,4.229 1.667,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.458,1.083 1.688,1.26 0.229,0.177 10 false IG 5.844,1.854 6.167,2.052 0.323,0.198 10 false RDA 5.823,2.656 6.208,2.865 0.385,0.208 10 false PRG 5.625,2.542 5.792,2.781 0.167,0.24 10 false 5 5.583,1.76 5.75,1.969 0.167,0.208 10 false 4 1.302,1.875 1.635,2.094 0.333,0.219 10 false RDA 1.302,2.656 1.646,2.854 0.344,0.198 10 false PRG 1.719,0.969 1.833,1.146 0.115,0.177 10 false 1 1.719,1.729 1.844,1.906 0.125,0.177 10 false 4 1.688,2.583 1.854,2.771 0.167,0.188 10 false 5 1.292,3.229 1.625,3.385 0.333,0.156 10 false GND 1.688,3.146 1.927,3.344 0.24,0.198 10 false 12 4,1.115 5.042,1.344 1.042,0.229 10 false from IG Circuit 5.448,3.615 5.833,3.823 0.385,0.208 10 false E118 2.396,1.271 3.438,1.5 1.042,0.229 10 false ECU-IG NO. 2 0.417,3.781 0.781,3.969 0.365,0.188 10 false L65

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Turn the ignition switch off.


b.

Disconnect the L65 tire pressure warning ECU and receiver connector.


c.

Disconnect the E118 main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-4 (RDA) - E118-4 (RDA) Always Below 1 Ω
L65-4 (RDA) or E118-4 (RDA) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
C420881E01
0.177,0.698 0.563,1 0.385,0.302 1.208,1.219 0.906,1.823 true 2.177,1.469 2.49,1.917 true 0.167,0.021 0.375,0.208 0.208,0.188 10 false *a 0.25,0.76 0.542,0.917 0.292,0.156 10 false L65 0.781,1.854 1.031,2.042 0.25,0.188 10 false IG 2.427,1.917 2.823,2.104 0.396,0.188 10 false GND

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-12 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L65-1 (IG) - Body ground Ignition switch ON 10 to 16 V




OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (B1247)
4.CHECK DTC OUTPUT (B1247)

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1247 is not output. A
DTC B1247 is output. for LHD B
for RHD C




A

END

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)