Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179/79  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. DTC Detection Condition Trouble Area
C2179/79 Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C281615E13
2.26,1.021 2.656,1.24 0.396,0.219 10 false PRG 2.635,0.906 2.927,1.167 0.292,0.26 10 false 5 4.708,1.01 5.115,1.208 0.406,0.198 10 false PRG 4.51,0.896 4.677,1.063 0.167,0.167 10 false 5 4.385,1.844 5.74,2.01 1.354,0.167 10 false L65 4.385,2.042 7.063,2.396 2.677,0.354 10 false Tire Pressure Warning ECU and Receiver 0.677,1.844 1.24,2.01 0.563,0.167 10 false E118 0.688,2.031 3.833,2.458 3.146,0.427 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Turn the ignition switch off.


b.

Disconnect the L65 tire pressure warning ECU and receiver connector.


c.

Disconnect the E118 main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-5 (PRG) - E118-5 (PRG) Always Below 1 Ω
L65-5 (PRG) or E118-5 (PRG) - Body ground Always 10 kΩ or higher




OK

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C2179/79 is not output. A
DTC C2179/79 is output. for LHD B
for RHD C




A

END

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)