Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1231  Steering Angle Sensor Circuit  


DESCRIPTION

The steering sensor signal is sent to the skid control ECU through the CAN communication system. When there is a malfunction in the communication system, it will be detected by the diagnosis function.

DTC Code DTC Detection Condition Trouble Area
C1231 When the ECU IG1 terminal voltage is 9.5 V or higher, the steering sensor malfunction signal is received.
·

Steering sensor

·

Harness or connector

·

Steering sensor power supply

·

CAN communication system

·

Skid control ECU (Master cylinder solenoid)

·

Steering control ECU (w/ VGRS System)



WIRING DIAGRAM

C257149E07
4.833,3.75 5.948,4.021 1.115,0.271 10 false Steering Sensor 0.708,3.542 3.594,3.771 2.885,0.229 10 false Skid Control ECU (Master Cylinder Solenoid) 1.354,2.375 2.396,2.667 1.042,0.292 10 false from IG Circuit 1.146,0.302 2.146,0.49 1,0.188 10 false from Battery 3.146,2.552 4.135,2.802 0.99,0.25 10 false ECU-IG No.2 2.552,0.51 3.344,0.75 0.792,0.24 10 false ECU-B1 4.896,2.844 5.167,3.063 0.271,0.219 10 false IG 5.865,2.844 6.292,3.073 0.427,0.229 10 false BAT 6,3.198 6.49,3.479 0.49,0.281 10 false ESS 5,2.594 5.292,2.802 0.292,0.208 10 false 1 6.021,2.594 6.354,2.792 0.333,0.198 10 false 3 6.385,3.094 6.781,3.323 0.396,0.229 10 false 2 0.906,4.354 3.271,4.563 2.365,0.208 10 false :CAN Communication System 4.844,3.594 5.219,3.844 0.375,0.25 10 false E11 0.729,3.365 1.146,3.594 0.417,0.229 10 false A24 3.76,1.552 5.26,1.833 1.5,0.281 10 false Steering Control ECU*2 5.115,1.135 5.625,1.375 0.51,0.24 10 false E79 4.75,1.146 5.198,1.406 0.448,0.26 10 false +BO 5.198,0.958 5.469,1.135 0.271,0.177 10 false 1 3.333,0.688 3.563,0.865 0.229,0.177 10 false *2 0.333,4.76 2.74,4.99 2.406,0.229 10 false *1: w/o VGRS System 4.844,0.25 5.313,0.51 0.469,0.26 10 false *1 0.333,5.031 2.188,5.24 1.854,0.208 10 false *2: w/ VGRS System 3.865,1.146 4.344,1.333 0.479,0.188 10 false +BI 3.531,1.135 3.969,1.354 0.438,0.219 10 false E77 3.573,0.948 3.76,1.104 0.188,0.156 10 false 10 5.552,1.979 5.885,2.229 0.333,0.25 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:
·

When U0073, U0100, U0114, U0123, U0124, U0126 or U0130 is output together with C1231, inspect and repair the trouble areas indicated by U0073, U0100, U0114, U0123, U0124, U0126 or U0130 first.

·

When the speed sensor or the yaw rate sensor assembly has trouble, DTCs of the steering sensor may be stored even when the steering sensor is normal. When DTCs of the speed sensor (C0200, C0205, C0210, C0215, C1235, C1236, C1238, C1239) or yaw rate sensor assembly (C1232, C1234, C1243, C1244, C1245, C1381) are output together with DTCs of the steering sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.



PROCEDURE

1.READ VALUE USING GTS (STEERING SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Angle Sensor Steering sensor/min.: -3276.8 degrees,
max.: 3276.7 degrees
Left turn: Increase
Right turn: Decrease
-


d.

Check that the steering wheel turning angle value of the steering sensor displayed on the GTS changes when turning the steering wheel.

OK:

Steering sensor value changes.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)
2.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 10 km/h (6 mph) or more for 10 seconds or more.



Result:
Result Proceed to
DTC is not output. A
DTC is output. LHD B
RHD C



A

B

C

3.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

Disconnect the steering sensor connector.


d.
C122523E13
1.479,0.521 1.906,0.781 0.427,0.26 0.51,1.417 1.01,1.417 true 1.406,1.885 1.208,1.885 1.208,1.885 1.208,1.469 true 0.094,0.031 0.406,0.229 0.313,0.198 10 false *a 1.573,0.552 2.031,0.75 0.458,0.198 10 false E11 0.323,1.333 0.635,1.531 0.313,0.198 10 false IG 1.448,1.792 1.76,1.99 0.313,0.198 10 false ESS

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E11-1 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-2 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering sensor connector.


c.
C122523E14
1.479,0.521 1.906,0.781 0.427,0.26 1.552,1.885 1.354,1.885 1.354,1.885 1.354,1.469 true 0.094,0.031 0.406,0.229 0.313,0.198 10 false *a 1.573,0.552 2.031,0.75 0.458,0.198 10 false E11 1.594,1.792 1.906,1.99 0.313,0.198 10 false BAT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E11-3 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)


Result:
Result Proceed to
OK A
NG (w/ VGRS) B
NG (w/o VGRS) C



A

B

5.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering control ECU connector.


c.
C139753E07
1.552,0.26 1.958,0.51 0.406,0.25 2.479,1.385 2.938,1.385 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 1.635,0.292 2.094,0.49 0.458,0.198 10 false E77 2.979,1.281 3.302,1.469 0.323,0.188 10 false +BI

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E77-10 (+BI) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the E11 steering sensor connector.


c.

Disconnect the E79 steering control ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-3 (BAT) - E79-1 (+BO) Always Below 1 Ω
E11-3 (BAT) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C