Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The master cylinder pressure sensor and pressure control sensor are connected to the skid control ECU in the master cylinder solenoid.

C182046E01
3.44,3.975 4.584,4.15 1.143,0.175 10 Skid Control ECU 3.477,2.63 3.745,2.805 0.268,0.175 10 IG1 4.123,2.635 4.636,2.817 0.512,0.182 10 VM/C1 4.123,3.123 4.636,3.295 0.512,0.172 10 PM/C1 3.468,3.116 3.822,3.292 0.354,0.175 10 STP 3.474,3.595 3.836,3.77 0.362,0.175 10 GND 5.459,2.639 5.984,2.814 0.525,0.175 10 VM/C1 5.459,3.117 5.984,3.292 0.525,0.175 10 PM/C1 5.459,3.573 6.289,3.748 0.831,0.175 10 M/C1 GND 3.9,3.577 4.678,3.752 0.778,0.175 10 M/C1 GND 4.123,0.485 4.636,0.668 0.512,0.182 10 VCTRL 4.123,0.974 4.636,1.146 0.512,0.172 10 PCTRL 5.459,0.49 5.984,0.665 0.525,0.175 10 VCTRL 5.459,0.968 5.984,1.143 0.525,0.175 10 PCTRL 5.459,1.424 6.289,1.599 0.831,0.175 10 CTRLGND 3.9,1.427 4.678,1.603 0.778,0.175 10 CTRLGND 0.297,3.137 1.77,3.336 1.472,0.2 10 from Stop Light Switch 0.726,3.593 1.848,3.768 1.122,0.175 10 to Body Ground 0.739,2.643 1.691,2.818 0.952,0.175 10 from IG Circuit 4.102,4.787 5.778,4.962 1.676,0.175 10 Master Cylinder Solenoid 0.37,5.681 4.977,5.856 4.608,0.175 10 VCTRL: Pressure Control Sensor Power Supply 0.37,5.983 4.22,6.159 3.85,0.175 10 PCTRL: Pressure Control Sensor Signal 0.37,6.259 3.755,6.435 3.386,0.175 10 CTRLGND: Pressure Control Sensor Ground 0.37,6.576 4.977,6.751 4.608,0.175 10 VM/C1: Master Cylinder Pressure Sensor Power Supply 0.37,6.879 4.22,7.054 3.85,0.175 10 PM/C1: Master Cylinder Pressure Sensor Signal 0.37,7.155 3.755,7.33 3.386,0.175 10 M/C1 GND: Master Cylinder Pressure Sensor Ground 5.407,3.941 6.627,4.395 1.221,0.455 10 Master Cylinder Pressure Sensor 5.407,1.792 6.516,2.135 1.109,0.343 10 Pressure Control Sensor

DTC Code DTC Detection Condition Trouble Area
C1246 When any of the following conditions is detected:
1.

All of the following conditions continue for at least 30 seconds.

-

The vehicle speed is more than 7 km/h (4 mph).

-

The PM/C1 or PCTRL terminal voltage exceeds 0.86 V.

-

The master cylinder pressure does not change by more than 0.048 MPa (0.5 kgf/cm2, 7.0 psi).


2.

The PM/C1 or PCTRL terminal receives interference at least 7 times within 5 seconds.

3.

Both of the following conditions continue for at least 1.2 seconds.

-

The stop light switch is off.

-

The PM/C1 or PCTRL terminal voltage is higher than 0.86 V or below 0.3 V.


4.

Both of the following conditions continue for at least 1.2 seconds.

-

The VM/C1 or VCTRL terminal voltage is between 4.4 and 5.6 V.

-

The PM/C1 or PCTRL terminal voltage is not between 0.19 and 4.57 V.



·

Master cylinder pressure sensor

·

Pressure control sensor

·

Stop light switch

·

Harness or connector

·

Master cylinder solenoid



CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When C1249 is output together with C1246, inspect and repair the trouble areas indicated by C1249 first.


PROCEDURE

1.READ VALUE USING GTS (MASTER CYLINDER SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor
reading/Min.: 0.00 V, Max.: 5.00 V
When brake pedal is released: 0.3 to 0.9 V The reading increases when the brake pedal is depressed.


d.

Check that the master cylinder pressure value of the master cylinder pressure sensor displayed on the GTS changes when depressing the brake pedal.


Result:
Result Proceed to
Master cylinder pressure sensor value does not change. LHD A
RHD B
Master cylinder pressure sensor value changes but it is not normal. C
Master cylinder pressure sensor value changes normally. D



A

B

C

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

D

4.RECONFIRM DTC
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

b.

Check the stop light switch installation (LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT/ RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT).

OK:

The brake pedal and stop light switch are normal.



Result:
Result Proceed to
OK A
NG LHD B
RHD C



A

3.INSPECT SKID CONTROL ECU (STP TERMINAL)

B

ADJUST BRAKE PEDAL AND/OR STOP LIGHT SWITCH

C

ADJUST BRAKE PEDAL AND/OR STOP LIGHT SWITCH

3.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.
C214161E76
0.167,0.688 0.594,0.938 0.427,0.25 1.688,1.146 2.5,0.688 true 0.115,0.021 0.427,0.219 0.313,0.198 10 false *a 0.24,0.719 0.698,0.917 0.458,0.198 10 false A24 2.552,0.583 3.01,0.781 0.458,0.198 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Stop light switch on
(Brake pedal depressed)
8 to 14 V
A24-7 (STP) - Body ground Stop light switch off
(Brake pedal released)
Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Check if the same DTC is output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



Result:
Result Proceed to
DTC is not output. A
DTC is output. LHD B
RHD C



A

B

C