Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1238  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239  Foreign Object is Attached on Tip of Rear Speed Sensor LH  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD, BA, VSC, A-TRC, CRAWL and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.

To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.

C173114E01
1.895,0.514 2.85,0.705 0.955,0.191 10 Speed Sensor 1.512,1.263 2.006,1.417 0.494,0.154 10 MRE A 1.512,1.562 2.006,1.716 0.494,0.154 10 MRE B 2.251,1.394 2.893,1.548 0.642,0.154 10 Sensor IC 4.015,2.013 4.657,2.204 0.642,0.191 10 Backward 6.263,0.507 6.991,0.698 0.728,0.191 10 High speed 5.647,0.0020 6.375,0.193 0.728,0.191 10 Low speed 6.693,1.268 7.074,1.411 0.381,0.143 10 2.6 V 6.693,1.479 7.074,1.621 0.381,0.143 10 1.4 V 6.693,1.71 7.074,1.852 0.381,0.143 10 0.7 V 5.419,2.013 5.992,2.162 0.573,0.149 10 Forward 0.076,2.384 2.697,2.575 2.622,0.191 10 Speed Sensor Rotor (Bearing Inner Race) 3.237,1.416 3.762,1.565 0.524,0.149 10 to ECU 3.177,1.088 3.398,1.279 0.221,0.191 10 (+) 3.177,1.768 3.361,1.959 0.184,0.191 10 (-) 5.523,1.224 5.523,0.083 5.523,0.083 5.6,0.083 false 6.168,1.226 6.168,0.581 6.168,0.581 6.228,0.581 false

DTC Code DTC Detection Condition Trouble Area
C1238
C1239
Noise in the speed sensor signals occurs 75 times or more for 5 seconds when the vehicle speed is 20 km/h (12 mph) or more.
·

Rear speed sensor RH

·

Rear speed sensor LH

·

Speed sensor rotor

·

Sensor installation

·

Skid control ECU (Master cylinder solenoid)



HINT:
·

DTC C1238 is for the rear speed sensor RH.

·

DTC C1239 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (RR/RL SPEED OPEN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open circuit detection/Error or Normal Normal -
RL Speed Open Rear speed sensor LH open circuit detection/Error or Normal Normal -

d.

Check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR/RL WHEEL SPEED, RR/RL WHEEL DIRECTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (RR/RL WHEEL SPEED, RR/RL WHEEL DIRECTION)
a.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.

OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.



b.

Check that the sensor signal conforms to the wheel direction.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Direction Rear wheel direction RH / Forward or Back Forward: Forward
Back: Back
-
RL Wheel Direction Rear wheel direction LH / Forward or Back Forward: Forward
Back: Back
-

OK:

The wheel direction is displayed correctly.



Result:
Proceed to
OK
NG



OK

3.PERFORM SIGNAL CHECK

NG

4.INSPECT REAR SPEED SENSOR INSTALLATION
3.PERFORM SIGNAL CHECK
a.

Check if test mode (signal check) DTCs are output.

HINT:

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.


Result:
Result Proceed to
Test mode (signal check) DTC is output. A
Test mode (signal check) DTC is not output. B




A

4.INSPECT REAR SPEED SENSOR INSTALLATION

B

10.RECONFIRM DTC
4.INSPECT REAR SPEED SENSOR INSTALLATION
a.
C144929E95
0.708,2.479 0.969,2.792 false 0.969,2.792 1.083,2.792 false 0.625,2.885 0.906,3.083 0.281,0.198 10 false *b 2.677,2.938 2.896,3.146 0.219,0.208 10 false *c 1.115,2.688 1.344,2.875 0.229,0.188 10 false *a 0.115,0.063 0.438,0.26 0.323,0.198 10 false *1

Check the speed sensor installation.

OK:

The installation nut is tightened properly.

There is no clearance between the sensor and rear axle.


Text in Illustration
*1 Rear Speed Sensor
*a No clearance
*b OK
*c NG


NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


Result:
Proceed to
OK
NG



OK

5.INSPECT SPEED SENSOR TIP

NG

5.INSPECT SPEED SENSOR TIP

b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR SPEED SENSOR

NG

6.INSPECT REAR SPEED SENSOR
a.

Install the rear speed sensor.


b.

Disconnect the z19 and/or z20 rear speed sensor connector.


c.
C173117E25
0.156,0.833 0.552,1.083 0.396,0.25 0.156,1.104 0.552,1.354 0.396,0.25 1.583,1.104 1.292,1.302 true 1.76,1.104 2.135,1.323 true 0.156,0.042 0.375,0.25 0.219,0.208 10 false *a 0.24,0.844 0.604,1.052 0.365,0.208 10 false z19 0.573,0.833 0.802,1 0.229,0.167 10 false *A 1.167,1.198 1.302,1.365 0.135,0.167 10 false 2 2.177,1.208 2.313,1.375 0.135,0.167 10 false 1 0.25,1.115 0.594,1.365 0.344,0.25 10 false z20 0.583,1.135 0.813,1.302 0.229,0.167 10 false *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Switch Condition Specified Condition
z19-2 (RR+) - Body ground Ignition switch off 10 kΩ or higher
z19-1 (RR-) - Body ground Ignition switch off 10 kΩ or higher

for LH:
Tester Connection Switch Condition Specified Condition
z20-2 (RL+) - Body ground Ignition switch off 10 kΩ or higher
z20-1 (RL-) - Body ground Ignition switch off 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear Speed Sensor)


Result:
Proceed to
OK
NG



OK

7.INSPECT SKID CONTROL SENSOR WIRE

NG

7.INSPECT SKID CONTROL SENSOR WIRE
U156224E01
0.057,0.026 0.247,0.188 0.191,0.163 10 *1 5.774,0.88 6.041,1.033 0.267,0.152 10 z19 1.14,0.843 1.384,0.995 0.243,0.152 10 z20 6.085,0.786 6.309,0.973 0.224,0.187 10 *A 1.433,0.73 1.672,0.913 0.239,0.184 10 *B 3.453,0.71 3.727,0.863 0.274,0.152 10 Nz1 1.666,2.099 2.003,2.262 0.336,0.163 10 RL+ 0.711,2.089 1.048,2.252 0.336,0.163 10 RL- 6.297,2.11 6.633,2.273 0.336,0.163 10 RR+ 5.337,2.11 5.674,2.273 0.336,0.163 10 RR- 1.125,1.549 0.803,1.942 0.803,1.942 0.803,2.04 false 1.431,1.562 1.776,1.935 1.776,1.935 1.778,2.032 false 5.758,1.577 5.436,1.969 5.436,1.969 5.436,2.068 false 6.065,1.59 6.41,1.962 6.41,1.962 6.412,2.06 false

Text in Illustration
*A for RH *B for LH
*1 Skid Control Sensor Wire - -

a.

Remove the skid control sensor wire.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Nz1-4 - z19-2 (RR+) Always Below 1 Ω
Nz1-3 - z19-1 (RR-) Always Below 1 Ω
Nz1-4 - Nz1-3 Always 10 kΩ or higher
Nz1-4 - Nz1-1 Always 10 kΩ or higher
Nz1-4 - Nz1-2 Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Nz1-2 - z20-2 (RL+) Always Below 1 Ω
Nz1-1 - z20-1 (RL-) Always Below 1 Ω
Nz1-2 - Nz1-1 Always 10 kΩ or higher
Nz1-2 - Nz1-3 Always 10 kΩ or higher
Nz1-2 - Nz1-4 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Disconnect the A24 skid control ECU connector and Nz1 skid control sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A24-5 (RR+) - Nz1-4 (RR+) Always Below 1 Ω
A24-5 (RR+) - Body ground Always 10 kΩ or higher
A24-19 (RR-) - Nz1-3 (RR-) Always Below 1 Ω
A24-19 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A24-20 (RL+) - Nz1-2 (RL+) Always Below 1 Ω
A24-20 (RL+) - Body ground Always 10 kΩ or higher
A24-6 (RL-) - Nz1-1 (RL-) Always Below 1 Ω
A24-6 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)
a.

Reconnect the A24 skid control ECU connector.


b.
C173272E10
0.354,1.188 0.792,1.49 0.438,0.302 1.906,1.417 2.625,1.24 true 1.906,1.615 2.656,1.74 true 0.219,0.073 0.531,0.271 0.313,0.198 10 false *a 0.458,1.24 0.917,1.438 0.458,0.198 10 false Nz1 2.677,1.146 3.135,1.344 0.458,0.198 10 false RL+ 2.688,1.656 3.146,1.854 0.458,0.198 10 false RR+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Switch Condition Specified Condition
Nz1-4 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH:
Tester Connection Switch Condition Specified Condition
Nz1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Result:
Result Proceed to
OK A
NG LHD B
RHD C



A

10.RECONFIRM DTC

B

C

10.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.


c.

Check if the same DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

11.REPLACE REAR SPEED SENSOR

B

11.REPLACE REAR SPEED SENSOR
a.

Replace the rear speed sensor (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



Result:
Proceed to
NEXT



NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.



HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

13.INSPECT SPEED SENSOR ROTOR

B

END

13.INSPECT SPEED SENSOR ROTOR
a.

Remove the rear axle hub and bearing assembly (Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>DISASSEMBLY).


b.

Check the sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.



NOTICE:

Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


Result:
Result Proceed to
NG A
OK LHD B
RHD C



A

CLEAN OR REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (SPEED SENSOR ROTOR)

B

C