| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FRONT BUMPER ASSEMBLY | - | - | - | - |
| *A | for Aero Type | - | - |
| *1 | NO. 1 HEADLIGHT CLEANER CLAMP | - | - |
| ● | Non-reusable part | - | - |
| *A | for Standard | *B | w/ Dynamic Radar Cruise Control System |
| *C | w/o Dynamic Radar Cruise Control System | - | - |
| *1 | NO. 1 HEADLIGHT CLEANER CLAMP | *2 | NO. 4 ENGINE ROOM WIRE |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight cleaner actuator removal/installation are shown below.
1.REMOVE FRONT BUMPER ASSEMBLY
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>REMOVAL
for Aero Type:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Aero Type)>REMOVAL
85353 3.REMOVE HEADLIGHT WASHER COVER RH (for Aero Type)
Use the same procedure as for the LH side.
85208A 4.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (for Aero Type)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
85207A 5.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (for Aero Type)
Use the same procedure as for the LH side.
85362 6.REMOVE NO. 2 WASHER BRACKET (for Aero Type)
|
|
Detach the wire harness clamp.
Remove the screw.
Heat the front bumper assembly and No. 2 washer bracket using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60°C (104 to 140°F) |
| No. 2 Washer Bracket |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the No. 2 washer bracket.
85361C 7.REMOVE WASHER BRACKET (for Aero Type)
Use the same procedure as for the No. 2 washer bracket.
85353 9.REMOVE HEADLIGHT WASHER COVER RH (for Standard)
Use the same procedure as for the LH side.
85208A 10.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (for Standard)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
85207A 11.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (for Standard)
Use the same procedure as for the LH side.
75310A 12.REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY (for Standard)
13.REMOVE NO. 7 RADIATOR GRILLE MOULDING (for Standard)
53101 14.REMOVE RADIATOR GRILLE SUB-ASSEMBLY (for Standard)
53113B 15.REMOVE RADIATOR SIDE GRILLE LH (for Standard)
53112B 16.REMOVE RADIATOR SIDE GRILLE RH (for Standard)
85362 17.REMOVE NO. 2 WASHER BRACKET (for Standard)
|
|
Heat the front bumper assembly and No. 2 washer bracket using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Front Bumper Assembly | 40 to 60°C (104 to 140°F) |
| No. 2 Washer Bracket |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the No. 2 washer bracket.
85361C 18.REMOVE WASHER BRACKET (for Standard)
Use the same procedure as for the No. 2 washer bracket.