| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO. 1 WIRE CLAMP BRACKET | - | ( ) |
- | - |
| 2 | NO. 2 RESERVOIR HOSE | - | ( ) |
- | - |
| 3 | NO. 1 RESERVOIR HOSE | - | ( ) |
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| *1 | BOOSTER BRACKET STOPPER RING
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
Lithium soap base glycol grease | * | For use with a union nut wrench |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | STOP LIGHT SWITCH ASSEMBLY | 84340 | - | - | - |
| 14 | BRAKE PEDAL RETURN SPRING | 47101A | ( ) |
- | - |
| *A | except 1GR-FE | - | - |
| *a | No. 1 Skid Control ECU |
| *b | No. 1 Reservoir Hose and No. 2 Reservoir Hose |
| *c | Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Brake Master Cylinder Reservoir |
| *f | No. 1 Brake Actuator Tube |
| *g | No. 1 Wire Clamp Bracket |
| *h | Brake Booster with Accumulator Pump Assembly |
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
After replacing the brake booster with master cylinder assembly, make sure to perform ECU configuration.
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) battery terminal.
1.INSTALL NO. 1 WIRE CLAMP BRACKET
|
|
Using a 5 mm long hexagon socket wrench, install the No. 1 wire clamp bracket with the bolt.
2.INSTALL NO. 2 RESERVOIR HOSE
|
|
| *a | View A | *b | View B |
| *c | Paint Mark | *d | Rib |
| *e | within 40° | *f | within 70° |
| *g | within 45° | - | - |
Install the No. 2 reservoir hose, and slide the 2 clips to secure it.
Make sure that the paint mark is facing the front of the vehicle (Upper Side).
Make sure that the paint mark is outside of the vehicle (Lower Side).
Install the clip within the range shown in the illustration.
3.INSTALL NO. 1 RESERVOIR HOSE
|
|
| *a | View A | *b | View B |
| *c | Paint Mark | *d | Rib |
| *e | within 40° | *f | within 70° |
| *g | within 45° | - | - |
Install the No. 1 reservoir hose, and slide the 2 clips to secure it.
Make sure that the paint mark is facing the front of the vehicle.
Install the clip within the range shown in the illustration.
44785D 4.INSTALL BRAKE MASTER CYLINDER GASKET
5.INSTALL BRAKE BOOSTER BRACKET
44785D 6.INSTALL BRAKE MASTER CYLINDER GASKET
|
|
47210L 7.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Install the brake booster with master cylinder assembly with the 4 nuts.
Do not apply excessive force to the brake lines.
Be careful not to allow brake fluid to enter the connector.
If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder assembly is filled with brake fluid.
| *a | No. 1 Skid Control ECU |
| *b | No. 1 Reservoir Hose and No. 2 Reservoir Hose |
| *c | Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Brake Master Cylinder Reservoir |
| *f | No. 1 Brake Actuator Tube |
| *g | No. 1 Wire Clamp Bracket |
| *h | Brake Booster with Accumulator Pump Assembly |
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
Install the siren with the nut.
Connect the connector.
47372 8.INSTALL NO. 2 BRAKE TUBE CLAMP
9.INSTALL BRAKE TUBE
| *1 | No. 2 Brake Tube Clamp | - | - |
| *a | Torque Wrench Fulcrum Length | *b | Union Nut Wrench |
| *c | From 1st Chamber of Brake Booster with Master Cylinder Assembly | *d | From 2nd Chamber of Brake Booster with Master Cylinder Assembly |
|
Paint Mark | - | - |
Engage the 2 clamps to connect the 2 brake tubes to the No. 2 brake tube clamp as shown in the illustration.
Using a union nut wrench, install the 2 brake tubes to the brake booster with master cylinder assembly and brake actuator assembly.
Do not kink or damage the brake tubes.
Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
51478C 10.INSTALL UPPER ENGINE SIDE UNDER COVER PLATE LH
82111 11.CONNECT ENGINE ROOM MAIN WIRE
|
|
47264A 12.INSTALL PUSH ROD PIN
|
Lithium Soap Base Glycol Grease | - | - |
Apply lithium soap base glycol grease to the push rod pin.
Connect the master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.
Be sure to install the push rod pin in the correct direction.
84340 13.INSTALL STOP LIGHT SWITCH ASSEMBLY
47101A 14.INSTALL BRAKE PEDAL RETURN SPRING
|
Front of the Vehicle | - | - |
Install the brake pedal return spring to the brake pedal support assembly as shown in the illustration.
Be sure to install the brake pedal return spring in the correct direction.
73900 15.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
16.FILL RESERVOIR WITH BRAKE FLUID
17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 1GR-FE:
for V35A-FTS:
18. UPDATE ECU SECURITY KEY
19.BLEED BRAKE SYSTEM
51474B 20.INSTALL ENGINE SIDE COVER LH (except 1GR-FE)
21.INSPECT AND ADJUST BRAKE PEDAL
22.PERFORM CALIBRATION
23. CHECK AND CLEAR DTC
24.INSPECT SRS WARNING LIGHT
25. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART