Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock ECU (steering lock actuator with ECU assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the ignition switch is turned to ON while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the ID code box (immobiliser code ECU) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

Steering Unlock Request Receive

·

S Code Check

·

L Code Check



WIRING DIAGRAM

E417564E12
3.281,2.813 3.594,3.01 0.313,0.198 10 false 24 3.281,3.25 3.594,3.448 0.313,0.198 10 false 11 3.281,3.885 3.594,4.083 0.313,0.198 10 false 29 5.156,0.25 5.469,0.448 0.313,0.198 10 false 7 5.156,2.813 5.469,3.01 0.313,0.198 10 false 3 5.146,3.24 5.458,3.438 0.313,0.198 10 false 4 5.146,3.875 5.458,4.073 0.313,0.198 10 false 1 3.104,0.333 4.479,0.563 1.375,0.229 10 false from Battery 4.375,0.5 5.75,0.698 1.375,0.198 10 false STRG LOCK 0.125,2.667 1.74,3.063 1.615,0.396 10 false ID Code Box (Immobiliser Code ECU) 2.135,4.396 2.594,4.594 0.458,0.198 10 false I39 2.115,4.563 3.604,4.969 1.49,0.406 10 false Certification ECU (Smart Key ECU Assembly) 4.448,4.427 4.906,4.625 0.458,0.198 10 false I49 4.417,4.583 7.083,4.99 2.667,0.406 10 false Steering Lock ECU (Steering Lock Actuator with ECU Assembly) 2.833,2.927 3.448,3.125 0.615,0.198 10 false SLR+ 2.875,3.365 3.49,3.563 0.615,0.198 10 false SLP 3.083,4.01 3.698,4.208 0.615,0.198 10 false E 5.365,0.354 5.979,0.552 0.615,0.198 10 false B 5.365,2.927 5.979,3.125 0.615,0.198 10 false IGE 5.365,3.354 5.979,3.552 0.615,0.198 10 false SLP 5.354,4.021 5.969,4.219 0.615,0.198 10 false GND 0.719,5.292 2.74,5.594 2.021,0.302 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.


·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not recur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the steering lock ECU (steering lock actuator with ECU assembly), ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After the ignition is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

If the steering lock ECU (steering lock actuator with ECU assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the ignition switch off, and then unlock the steering by pressing the engine switch.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the electrical key transmitter sub-assembly is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → ACC → ON → Off




Result:
Proceed to
OK
NG



OK

2.CHECK MULTI-INFORMATION DISPLAY

NG

2.CHECK MULTI-INFORMATION DISPLAY
a.

With the ignition switch ON, check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
Steering Lock active is displayed A
Steering Lock active is not displayed B



A

3.CHECK STEERING UNLOCK

B

5.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
3.CHECK STEERING UNLOCK
a.

Turn the steering wheel left and right, and then press the engine switch.


b.

Check that the steering is unlocked.


Result:
Result Proceed to
The steering is unlocked A
The steering is not unlocked B



A

END (STEERING LOCK NORMAL)

B

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
NOTICE:

If a malfunction occurs, do not remove/install the vehicle battery before checking for DTCs.


OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

5.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds of turning the ignition switch to ACC or ON or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (S CODE CHECK)

NG

14.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
6.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU was replaced, but not registered.

·

An ECU was replaced with an ECU which has already been registered to another vehicle.




Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (L CODE CHECK)

NG

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator with ECU assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator with ECU assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)

NG

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C396300C60
0.323,2.906 1.646,3.042 1.323,0.135 2.344,2.948 2.75,3.073 0.406,0.125 1.615,4.063 2.375,4.177 0.76,0.115 1.531,0.177 1.969,0.406 0.438,0.229 0.896,3.25 0.896,3.042 false 2.573,3.281 2.573,3.073 false 2.01,4.063 2.01,3.854 false 0.813,1.802 1.875,1.104 true 2.792,1.646 2.302,1.083 true 0.271,0.26 0.583,0.417 0.313,0.156 10 false *a 0.823,3.281 1.135,3.438 0.313,0.156 10 false *c 1.917,3.688 2.229,3.844 0.313,0.156 10 false *d 2.5,3.302 2.813,3.458 0.313,0.156 10 false *c 0.646,1.854 1.104,2.052 0.458,0.198 10 false IGE 2.76,1.698 3.219,1.896 0.458,0.198 10 false GND 2.969,4.083 3.427,4.281 0.458,0.198 10 false GND 1.635,0.208 2.094,0.406 0.458,0.198 10 false I49 0.083,2.458 0.396,2.615 0.313,0.156 10 false *b
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))
*b Waveform
*c Steering lock motor not operating
*d Steering lock motor operating


Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Check the signal waveform according to the condition(s) in the table below.

Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - I49-1 (GND) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off


2 V/DIV., 200 ms./DIV. Pulse generation
(See waveform)


Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
10.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C342409C75
1.531,0.844 2.01,1.125 0.479,0.281 1.917,1.938 2.667,2.656 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.646,0.906 1.958,1.063 0.313,0.156 10 false I49 2.615,2.708 2.917,2.885 0.302,0.177 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Connect the I39 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator with ECU assembly) with a new one and perform registration.

HINT:
·

For registration.

Refer to Service Bulletin.




b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator with ECU assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator with ECU assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C342409C76
1.5,0.896 1.917,1.146 0.417,0.25 2.75,2.677 1.729,1.948 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.583,0.927 1.896,1.125 0.313,0.198 10 false I49 2.76,2.698 3.24,2.896 0.479,0.198 10 false SLP
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-4 (SLP) - Body ground Steering locked 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

16.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
15.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Turn the ignition switch to ON.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds after the ignition switch is turned to ACC or ON or the engine is started, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

16.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

17.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.READ VALUE USING GTS (STEERING UNLOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator with ECU assembly) with a new one and perform registration.

HINT:
·

For registration.

Refer to Service Bulletin.




b.

Turn the ignition switch to ON.


c.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of ignition switch turned ACC or ON, or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (ignition switch not turned ACC or ON, and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock Request Receive
50003 440 62
OK:

Within 10 seconds of turning the ignition switch to ACC or ON or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) WAS)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)