Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.04–2021.07
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line (for LHD)  


DESCRIPTION

Symptom Trouble Area

*1: w/ Automatic Transmission System (for AJA0F)

*2: w/ Stop and Start System

There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

TCM*1

·

ECM

·

Engine stop and start ECU*2

·

No. 7 global CAN junction connector



WIRING DIAGRAM

C459255E04
5.156,1.521 7.104,1.927 1.948,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.719,1.667 2.667,2.073 1.948,0.406 10 false TCM*1 6.219,3.583 6.729,3.865 0.51,0.281 10 false ECM 2.813,3.594 4.458,4.031 1.646,0.438 10 false No. 7 Global CAN Junction Connector 5.146,1.375 5.646,1.594 0.5,0.219 10 false I42 6.219,0.594 6.719,0.813 0.5,0.219 10 false CA4H 6.24,1.177 6.74,1.396 0.5,0.219 10 false CA4L 6.26,2.625 6.76,2.844 0.5,0.219 10 false CANH 5.698,0.594 6,0.833 0.302,0.24 10 false 26 5.698,1.031 6,1.271 0.302,0.24 10 false 25 6.271,3.208 6.771,3.427 0.5,0.219 10 false CANL 5.688,2.521 5.99,2.76 0.302,0.24 10 false 11 5.656,2.99 5.958,3.229 0.302,0.24 10 false 19 0.875,0.698 1.375,0.917 0.5,0.219 10 false CANH 0.917,1.115 1.417,1.333 0.5,0.219 10 false CANL 1.396,1.021 1.698,1.26 0.302,0.24 10 false 21 1.396,0.604 1.698,0.844 0.302,0.24 10 false 20 2.802,3.427 3.302,3.646 0.5,0.219 10 false I118 0.74,1.5 1.24,1.719 0.5,0.219 10 false C36 3.156,0.594 3.458,0.833 0.302,0.24 10 false 10 3.177,1.031 3.479,1.271 0.302,0.24 10 false 21 4.042,1.021 4.344,1.26 0.302,0.24 10 false 18 4.063,0.604 4.365,0.844 0.302,0.24 10 false 7 4.031,3.031 4.333,3.271 0.302,0.24 10 false 19 4.052,2.604 4.354,2.844 0.302,0.24 10 false 8 0.906,2.698 1.406,2.917 0.5,0.219 10 false CANH 0.938,3.146 1.438,3.365 0.5,0.219 10 false CANL 1.375,2.615 1.677,2.854 0.302,0.24 10 false 13 1.375,3.052 1.677,3.292 0.302,0.24 10 false 14 0.281,3.521 0.781,3.74 0.5,0.219 10 false I57 0.25,3.677 2.188,4.052 1.938,0.375 10 false Engine Stop and Start ECU*3 3.156,3.021 3.458,3.26 0.302,0.24 10 false 20 3.208,2.615 3.51,2.854 0.302,0.24 10 false 9 5.281,2.521 5.583,2.76 0.302,0.24 10 false 18 5.292,2.698 5.594,2.938 0.302,0.24 10 false B1 5.646,2.698 5.948,2.938 0.302,0.24 10 false B2 5.271,2.865 5.573,3.104 0.302,0.24 10 false *1 5.677,2.865 5.979,3.104 0.302,0.24 10 false *2 5.281,2.99 5.583,3.229 0.302,0.24 10 false 17 5.302,3.125 5.604,3.365 0.302,0.24 10 false B1 5.688,3.146 5.99,3.385 0.302,0.24 10 false B2 5.292,3.323 5.594,3.563 0.302,0.24 10 false *1 5.688,3.313 5.99,3.552 0.302,0.24 10 false *2 0.208,4.375 2.146,4.75 1.938,0.375 10 false *1: for V35A-FTS 1.688,4.375 3.625,4.75 1.938,0.375 10 false *2: for 1GR-FE 2.969,4.344 5.167,4.719 2.198,0.375 10 false *3: w/ Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

47.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-26 (CA4H) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-25 (CA4L) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-26 (CA4H) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-25 (CA4L) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

6.CHECK VEHICLE TYPE

NG

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

8.CHECK VEHICLE TYPE
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

OK

8.CHECK VEHICLE TYPE

NG

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
8.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

10.CHECK VEHICLE TYPE
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

10.CHECK VEHICLE TYPE

NG

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
10.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for 1GR-FE A
except 1GR-FE B



A

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

12.CHECK VEHICLE TYPE
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

12.CHECK VEHICLE TYPE

NG

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
12.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B2 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the I57 engine stop and start ECU connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

20.CHECK VEHICLE TYPE

NG

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
20.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

22.CHECK VEHICLE TYPE
21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

OK

22.CHECK VEHICLE TYPE

NG

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
22.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

24.CHECK VEHICLE TYPE
23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

24.CHECK VEHICLE TYPE

NG

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
24.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for 1GR-FE A
except 1GR-FE B



A

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

26.CHECK VEHICLE TYPE
25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

26.CHECK VEHICLE TYPE

NG

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
26.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B2 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the I57 engine stop and start ECU connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-7 (CANH) - I118-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

34.CHECK VEHICLE TYPE

NG

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
34.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

36.CHECK VEHICLE TYPE
35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-10 (CANH) - I118-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

36.CHECK VEHICLE TYPE

NG

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
36.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

38.CHECK VEHICLE TYPE
37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

38.CHECK VEHICLE TYPE

NG

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
38.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for 1GR-FE A
except 1GR-FE B



A

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

40.CHECK VEHICLE TYPE
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

40.CHECK VEHICLE TYPE

NG

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
40.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-9 (CANH) - I118-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-7 (CANH) - I118-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-10 (CANH) - I118-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR- TCM)

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B2 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the I57 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-9 (CANH) - I118-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

47.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-7 (CANH) - I118-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

48.CHECK VEHICLE TYPE

NG

52.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
48.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

49.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

50.CHECK VEHICLE TYPE
49.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

50.CHECK VEHICLE TYPE

NG

53.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
50.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for 1GR-FE A
except 1GR-FE B



A

51.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

51.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-8 (CANH) - I118-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

54.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
52.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

53.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the B1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-18 (CANH) - B1-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

54.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the B2 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B2-11 (CANH) - B2-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)