Home › Engine / Hybrid System › V35A-FTS (ENGINE MECHANICAL) › ENGINE UNIT
RM38G0E _51 Engine / Hybrid System _100652 V35A-FTS ENGINE MECHANICAL _0467575 ENGINE UNIT G

V35A-FTS ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT VALVE ROCKER ARM SUB-ASSEMBLY

a.
A366101

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free of dirt and foreign objects.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  

A377673C01
2.188,0.594 2.635,0.594 false 2.104,1.271 2.677,1.271 false 2.125,2.344 2.313,2.344 2.313,2.344 2.875,2.083 true 5.25,1.344 5.438,0.719 5.438,0.719 5.625,0.719 true 1.083,2.49 1.083,2.271 true 2.135,1.771 2.771,1.771 true 2.885,2.5 2.885,2.281 true 1.24,1.771 1.875,1.771 true 1.865,2.344 1.688,2.344 1.688,2.344 1.146,2.115 true 2.698,1 2.219,0.854 2.219,0.854 2.083,0.854 false 1.302,1.073 1.719,0.854 1.719,0.854 1.844,0.854 false 1.427,0.604 1.781,0.604 false 1.354,1.271 1.875,1.271 false 1.063,0.083 1.375,0.281 0.313,0.198 10 false *a 2.854,0.083 3.167,0.281 0.313,0.198 10 false *b 1.906,0.781 2.208,0.979 0.302,0.198 10 false *c 1.927,1.188 2.104,1.365 0.177,0.177 10 false *d 1.938,1.688 2.125,1.875 0.188,0.188 10 false *e 1.927,2.271 2.24,2.469 0.313,0.198 10 false *f 1,2.49 1.313,2.688 0.313,0.198 10 false *g 2.813,2.49 3.125,2.688 0.313,0.198 10 false *g 1.865,0.51 2.156,0.688 0.292,0.177 10 false SST 5.677,0.635 5.979,0.833 0.302,0.198 10 false SST
*a CORRECT *b INCORRECT
*c Tapered Path *d Plunger
*e Low Pressure Chamber *f Check Ball
*g High Pressure Chamber - -



c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


HINT:

If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster assembly with a new one.



Hide 13501B 3.INSPECT CAMSHAFT

a.

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.
A475759

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


HINT:
·

If the runout is more than the maximum, replace the camshaft.

·

Check the oil clearance after replacing the camshaft.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION





b.
A475760

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake camshaft for Bank 1 42.619 to 42.719 mm (1.67791 to 1.68184 in.)
for Bank 2 42.619 to 42.719 mm (1.67791 to 1.68184 in.)
Exhaust camshaft for Bank 1 38.539 to 38.639 mm (1.51728 to 1.52121 in.)
for Bank 2 38.539 to 38.639 mm (1.51728 to 1.52121 in.)
for Fuel Pump 35.550 to 35.650 mm (1.39960 to 1.40354 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake camshaft for Bank 1 42.559 mm (1.67554 in.)
for Bank 2 42.559 mm (1.67554 in.)
Exhaust camshaft for Bank 1 38.479 mm (1.51491 in.)
for Bank 2 38.479 mm (1.51491 in.)
for Fuel Pump 35.490 mm (1.3972 in.)


HINT:

If the cam lobe height is less than the minimum, replace the camshaft.



c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 Journal for Intake Side 40.984 to 41.000 mm (1.61354 to 1.61417 in.)
for Exhaust Side 40.984 to 41.000 mm (1.61354 to 1.61417 in.)
Other Journals 23.959 to 23.975 mm (0.94326 to 0.94389 in.)


HINT:

If the journal diameter is not as specified, check the oil clearance.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 11101A 4.INSPECT CYLINDER HEAD SET BOLT

a.
A416992C02
0.219,0.719 0.531,0.875 0.313,0.156 10 false *a 0.208,3.031 0.521,3.188 0.313,0.156 10 false *b 2.271,0.563 2.583,0.719 0.313,0.156 10 false *c 1.271,1.917 1.583,2.073 0.313,0.156 10 false *d 2.25,2.854 2.563,3.01 0.313,0.156 10 false *c 1.302,4.188 1.615,4.344 0.313,0.156 10 false *d
*a Bolt A
*b Bolt B
*c Measurement Point
*d Measurement Point (Distance from the Seat)


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:
for bolt A:

11.972 to 11.760 mm (0.471 to 0.463 in.)

for bolt B:

10.974 to 10.794 mm (0.432 to 0.425 in.)


Minimum Diameter:
for bolt A:

11.60 mm (0.457 in.) less than

for bolt B:

10.60 mm (0.417 in.) less than


Measurement Point (Distance from the Seat):
for bolt A:

115 mm (4.52 in.)

for bolt B:

105 mm (4.13 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 13506A 5.INSPECT NO. 1 CHAIN SUB-ASSEMBLY

a.
A382970C03
1.625,0.927 1.938,1.125 0.313,0.198 10 false *a
*a Measurement Area


Using a spring scale, pull the No. 1 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

137.38 mm (5.40 in.)


HINT:

Perform the measurement at 3 random places. If a measurement is more than the maximum, replace the No. 1 chain sub-assembly.



Hide 13507 6.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A382970C06
1.625,0.927 1.938,1.125 0.313,0.198 10 false *a
*a Measurement Area


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

115.72 mm (4.55 in.)


HINT:

Perform the measurement at 3 random places. If a measurement is more than the maximum, replace the No. 2 chain sub-assembly.



Hide 13507C 7.INSPECT OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.
A382970C01
1.625,0.906 1.938,1.104 0.313,0.198 10 false *a
*a Measurement Length


Using a spring scale, pull the oil pump drive chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

116.35 mm (4.58 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the oil pump drive chain sub-assembly.



Hide 13519B 8.INSPECT OIL PUMP DRIVE SPROCKET

a.
A419233

Place the oil pump drive chain sub-assembly around the oil pump drive sprocket.


b.

Using a vernier caliper, measure the diameter of the oil pump drive sprocket with the oil pump drive chain sub-assembly.

Minimum Gear Diameter (with Oil Pump Drive Chain Sub-assembly):

62.39 mm (2.45 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the oil pump drive chain sub-assembly and oil pump drive sprocket.



Hide 15163D 9.INSPECT OIL PUMP DRIVE SHAFT SPROCKET

a.
A419234

Place the oil pump drive chain sub-assembly around the oil pump drive shaft sprocket.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft sprocket with the oil pump drive chain sub-assembly.

Minimum Gear Diameter (with Oil Pump Drive Chain Sub-assembly):

57.31 mm (2.25 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the oil pump drive chain sub-assembly and oil pump drive shaft sprocket.



Hide 13050B 10.INSPECT CAMSHAFT TIMING INTAKE GEAR ASSEMBLY

a.
A475762

for No. 1 Chain Sub-assembly Side:

i.

Place the No. 1 chain sub-assembly around the camshaft timing intake gear assembly.


ii.

Using a vernier caliper, measure the diameter of the camshaft timing intake gear assembly with the No. 1 chain sub-assembly.

Minimum Gear Diameter (with No. 1 Chain Sub-assembly):

113.74 mm (4.47 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and camshaft timing intake gear assembly.




b.
A475761

for No. 2 Chain Sub-assembly Side:

i.

Place the No. 2 chain sub-assembly around the camshaft timing intake gear assembly.


ii.

Using a vernier caliper, measure the diameter of the camshaft timing intake gear assembly with the No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

74.55 mm (2.93 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing intake gear assembly.




Hide 13070 11.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A475763

Place the No. 2 chain sub-assembly around the camshaft timing exhaust gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

75.01 mm (2.95 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing exhaust gear assembly.



Hide 13521 12.INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET

a.

Place the No. 1 chain sub-assembly around the crankshaft timing gear or sprocket.


b.
A419233

Using a vernier caliper, measure the diameter of the crankshaft timing gear or sprocket with the No. 1 chain sub-assembly.

Minimum Sprocket Diameter (with No. 1 Chain Sub-assembly):

59.76 mm (2.35 in.)


NOTICE:

The vernier caliper must contact the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and crankshaft timing gear or sprocket.



Hide 13530 13.INSPECT IDLE SPROCKET ASSEMBLY

a.

Place the No. 1 chain sub-assembly around the idle sprocket assembly.


b.
A366113

Using a vernier caliper, measure the diameter of the idle sprocket assembly with the No. 1 chain sub-assembly.

Minimum Sprocket Diameter (with No. 1 Chain Sub-assembly):

65.8 mm (2.59 in.)


NOTICE:

The vernier caliper must contact the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and idle sprocket assembly.



Hide 14.INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

a.
A366114

Using a micrometer, measure the No. 1 idle gear shaft diameter.

Standard No. 1 idle gear shaft diameter:

22.987 to 23.000 mm (0.905 to 0.906 in.)



b.
A366115

Using a caliper gauge, measure the inside diameter of the idle sprocket assembly.

Standard idle sprocket assembly inside diameter:

23.020 to 23.030 mm (0.906 to 0.907 in.)



c.

Subtract the No. 1 idle gear shaft diameter measurement from the idle sprocket assembly inside diameter measurement.

Standard oil clearance:

0.020 to 0.043 mm (0.000787 to 0.00169 in.)


Maximum oil clearance:

0.093 mm (0.00366 in.)


HINT:

If the oil clearance is more than the maximum, replace the No. 1 idle gear shaft and idle sprocket assembly.



Hide 13540 15.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A416997C02
1.979,1.219 2.271,0.969 2.271,0.969 2.479,0.969 false 0.802,1.969 1.031,1.969 1.031,1.969 1.354,1.583 true 2.51,0.865 2.823,1.021 0.313,0.156 10 false *a 0.625,1.865 0.938,2.021 0.313,0.156 10 false *b
*a Plunger
*b Stopper Plate


Turn the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

HINT:

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.



Hide 13550 16.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A416998C03
3.198,0.385 3.375,0.615 0.177,0.229 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 2 chain tensioner assembly.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.



Hide 13560A 17.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A416999C02
3.198,0.396 3.365,0.594 0.167,0.198 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 3 chain tensioner assembly.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.



Hide 13559 18.INSPECT CHAIN TENSIONER SLIPPER

a.
A417000C02
3.01,0.938 3.323,1.094 0.313,0.156 10 false *a
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13561 19.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A475764C02
3.01,1.031 3.323,1.188 0.313,0.156 10 false *a
*a Depth


Measure the wear depth of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13562 20.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A417002C01
3.104,0.948 3.281,1.208 0.177,0.26 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 2 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 2 chain vibration damper.



Hide 21.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Inspect the camshaft thrust clearance (for Bank 1).

i.

Install the intake camshaft sub-assembly RH.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CYLINDER HEAD GASKET>INSTALLATION


ii.

Install the exhaust camshaft sub-assembly RH.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CYLINDER HEAD GASKET>INSTALLATION


iii.
A475765

Using a dial indicator, measure the thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.06 to 0.20 mm (0.00236 to 0.00787 in.)


Maximum Thrust Clearance:

0.25 mm (0.00984 in.)


HINT:
·

If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly RH.

·

If the thrust surface is damaged, replace the intake camshaft sub-assembly RH or exhaust camshaft sub-assembly RH.





b.

Inspect the camshaft thrust clearance (for Bank 2).

i.

Install the intake camshaft sub-assembly LH.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CYLINDER HEAD GASKET>INSTALLATION


ii.

Install the exhaust camshaft sub-assembly LH.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CYLINDER HEAD GASKET>INSTALLATION


iii.

Using a dial indicator, measure the thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.06 to 0.20 mm (0.00236 to 0.00787 in.)


Maximum Thrust Clearance:

0.25 mm (0.00984 in.)


HINT:
·

If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly LH.

·

If the thrust surface is damaged, replace the intake camshaft sub-assembly LH or exhaust camshaft sub-assembly LH.





Hide 22.INSPECT CAMSHAFT OIL CLEARANCE

a.

for Bank 1:

i.

Clean the camshaft bearing caps, camshaft housing sub-assembly RH and camshaft journals.


ii.

Place the camshafts onto the camshaft housing sub-assembly RH.


iii.
A475766C02
1.833,1.125 1.948,1.646 1.948,1.646 2.135,1.646 true 2.167,1.573 2.385,1.76 0.219,0.188 10 true *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


iv.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



v.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


vi.
A475767C02
2.479,3.333 2.823,3.708 true 1.844,1.156 2.042,1.656 2.042,1.656 2.24,1.656 true 0.771,2.99 1.615,2.396 true 1.375,2.969 1.625,2.396 true 2.063,2.969 1.646,2.406 true 0.76,3.688 1.385,4.427 true 1.323,3.719 1.406,4.427 true 1.417,4.417 2.063,3.719 true 2.479,3.333 2.854,2.979 true 2.26,1.583 2.51,1.75 0.25,0.167 10 true *a 2.313,3.271 2.625,3.427 0.313,0.156 10 false *b 1.344,4.448 1.656,4.604 0.313,0.156 10 false *c 1.542,2.24 1.854,2.396 0.313,0.156 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.035 to 0.072 mm (0.00137 to 0.00283 in.)
Other journals 0.025 to 0.057 mm (0.000984 to 0.00224 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.085 mm (0.00334 in.)
Other journals 0.085 mm (0.00334 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the intake camshaft sub-assembly RH or exhaust camshaft sub-assembly RH.

·

If necessary, replace the camshaft housing sub-assembly RH.





b.

for Bank 2:

i.

Clean the camshaft bearing caps, camshaft housing sub-assembly LH and camshaft journals.


ii.

Place the camshafts onto the camshaft housing sub-assembly LH.


iii.
A475768C02
0.885,0.51 1.083,0.51 1.083,0.51 1.219,0.823 true 0.646,0.438 0.865,0.667 0.219,0.229 10 true *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


iv.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



v.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


vi.
A475769C02
1.688,4.458 0.896,3.813 true 0.844,0.5 1.052,0.5 1.052,0.5 1.198,0.844 true 0.542,3.146 1.031,3.469 true 0.542,3.781 1.031,3.479 true 0.927,3.115 1.74,2.396 true 1.531,3.115 1.771,2.396 true 2.208,3.104 1.771,2.406 true 2.802,3.094 1.802,2.406 true 1.708,4.458 1.521,3.833 true 1.719,4.448 2.219,3.802 true 1.729,4.458 2.781,3.813 true 0.625,0.427 0.813,0.667 0.188,0.24 10 true *a 1.073,3.385 1.385,3.542 0.313,0.156 10 false *b 1.698,2.24 2.01,2.396 0.313,0.156 10 false *c 1.615,4.479 1.927,4.635 0.313,0.156 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.035 to 0.072 mm (0.00137 to 0.00283 in.)
Other journals 0.025 to 0.057 mm (0.000984 to 0.00224 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.085 mm (0.00334 in.)
Other journals 0.085 mm (0.00334 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the intake camshaft sub-assembly LH or exhaust camshaft sub-assembly LH.

·

If necessary, replace the camshaft housing sub-assembly LH.