Home › Vehicle Interior › LIGHTING (INT) › GLOVE BOX LIGHT › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100749 LIGHTING (INT) _0467846 GLOVE BOX LIGHT A

LIGHTING (INT)  GLOVE BOX LIGHT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E508192N01
5.417,2.073 5.948,2.073 false 4.917,0.896 5.26,0.896 false 2.833,0.438 3.333,0.438 false 0.5,2.219 0.5,2.833 false 0.448,0.813 0.802,0.813 0.802,0.813 0.958,1.01 false 2.792,1.729 2.792,1.813 2.792,1.813 3.99,1.813 false 2.083,2.208 2.365,2.208 2.365,2.208 2.583,2.469 false 1.813,3.083 2.313,3.083 false 3.76,3.292 3.958,3.49 3.958,3.49 4.313,3.49 false 6.083,3 6.583,3 false 6.302,0.635 6.802,0.635 false 6.302,0.24 6.802,0.24 false 3.615,1.802 3.615,1.521 false 6.625,2.854 6.906,3.208 0.281,0.354 18 false 4 6.104,0.458 6.385,0.813 0.281,0.354 18 false 2 5.583,0.719 5.865,1.073 0.281,0.354 18 false 6 3.375,0.281 3.802,0.677 0.427,0.396 18 false 11 4.313,1.677 4.729,2.021 0.417,0.344 18 false 10 1.906,2.083 2.188,2.438 0.281,0.354 18 false 9 0.125,0.646 0.49,1 0.365,0.354 18 false 12 0.552,2.875 0.833,3.229 0.281,0.354 18 false 7 2.375,2.927 2.656,3.281 0.281,0.354 18 false 8 4.344,3.354 4.625,3.708 0.281,0.354 18 false 3 6.01,1.948 6.292,2.302 0.281,0.354 18 false 5 6.104,0.094 6.385,0.448 0.281,0.354 18 false 1 3.74,0.979 4.021,1.333 0.281,0.354 10 false x 4 4.313,2.542 4.594,2.896 0.281,0.354 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - (Click here) - -
3 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55607 - - -
4 FRONT DOOR SCUFF PLATE RH 67913B - - -
5 COWL SIDE TRIM BOARD RH 62111C - - -
6 NO. 1 INSTRUMENT SIDE PANEL 55317E (Click here) - -
7 LOWER NO. 2 INSTRUMENT PANEL PAD SUB-ASSEMBLY 55403H (Click here) - -
8 INNER NO. 1 INSTRUMENT PANEL BRACKET COVER RH 55394D - - -
9 LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 73990 (Click here) - -
10 INSTRUMENT PANEL BOX DOOR COVER 55443A (Click here) - -
11 LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY 55320 - - -
12 NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY 81080J - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 interior illumination light assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 55607 3.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67913B 4.REMOVE FRONT DOOR SCUFF PLATE RH

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 62111C 5.REMOVE COWL SIDE TRIM BOARD RH

a.

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55317E 6.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Z101186

·

Use the same procedure described for the No. 2 instrument side panel.

Click here(Click here)



Hide 55403H 7.REMOVE LOWER NO. 2 INSTRUMENT PANEL PAD SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 55394D 8.REMOVE INNER NO. 1 INSTRUMENT PANEL BRACKET COVER RH

Hide 73990 9.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Z101186

Click here(Click here)

Hide 55443A 10.REMOVE INSTRUMENT PANEL BOX DOOR COVER

Z101186

Click here(Click here)

Hide 55320 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 81080J 12.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

a.
E465596C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)