The cooler thermistor (ambient temperature sensor) is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system.
The cooler thermistor (ambient temperature sensor) detects fluctuations in the ambient temperature and sends it as a signal to the combination meter assembly.
This data is used for controlling the cabin temperature.
The resistance of the cooler thermistor (ambient temperature sensor) changes in accordance with the ambient temperature.
As the temperature decreases, the resistance increases.
The combination meter assembly applies voltage (5 V) to the cooler thermistor (ambient temperature sensor) and detects voltage changes due to changes in the resistance of the cooler thermistor (ambient temperature sensor).
The cooler thermistor (ambient temperature sensor) detects the ambient temperature in its vicinity, not the ambient temperature around the vehicle.
Depending on factors such as radiant heat from the engine room and the vehicle speed, the ambient temperature detected by the cooler thermistor (ambient temperature sensor) may differ from the ambient temperature displayed on the multi-information display in the combination meter assembly.
For example:
When the vehicle is stopped or being driven at low speeds, the displayed ambient temperature will not be updated to a higher temperature to adjust for and minimize the influence of radiant heat from the engine room on the air conditioning system control.
When the vehicle is not being driven at low speeds, the adjustment is performed, but updating of the displayed ambient temperature to a higher temperature is delayed.
The displayed ambient temperature will be updated to a lower temperature regardless of the vehicle speed.
When the ambient temperature around the cooler thermistor (ambient temperature sensor) suddenly changes due to any reason other than radiant heat from the engine room, such as when the vehicle enters or exits a garage or tunnel, the actual ambient temperature of the vehicle and the displayed ambient temperature may differ or changing of the displayed value may be delayed.
Before starting the inspection, it is necessary to release the residual heat from the engine room (engine unit and coolant hoses, etc.) after stopping the engine and electric motor (when the vehicle is parked after being driven). Therefore, move and park the vehicle in the following type of temperature measurement location.
A location within the vehicle service area which has a relatively low amount of environmental temperature changes in the area surrounding the vehicle.
A location with a level surface made of a material such as concrete which transmits a relatively low amount of heat from the ground, such as concrete.
A location with no heat influences around the vehicle to be inspected such as other vehicles with a running engine and electric motors, exhaust gas ducts installed on the exhaust pipes, stoves, etc.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Ignition switch operation during parked vehicle inspection:
Turn the ignition switch to ON. (Do not start the engine and electric motor.)
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC P007011 and P007015 are not output | A |
| DTC P007011 is output | B |
| DTC P007015 is output | C |
A
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
During the parked vehicle inspection, perform the inspection with the ignition switch off (do not start the engine and electric motor).
Disconnect the A9 cooler thermistor (ambient temperature sensor) connector.
Disconnect the I32 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(A9,I32)Location & Routingewd_type=routing;type=c,c;code=A9,I32 Click Connector(A9)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Cooler (Ambient Temperature Sensor) Thermistorewd_type=component;type=c;code=A9;pinno=2,1 |
||
| A9-2 - I32-1 (TAM) | Always | Below 1 Ω |
| A9-1 - I32-14 (SG-2) | Always | Below 1 Ω |
| A9-2 or I32-1 (TAM) - Other terminals and body ground | Always | 10 kΩ or higher |
| A9-1 - I32-14 (SG-2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
The air conditioning amplifier assembly reads and memorizes the cooler thermistor (ambient temperature sensor) detection value (THO) from before the ignition switch was turned off for 1 hour after turning the ignition switch off. Therefore, it is necessary to switch off the air conditioning amplifier assembly internal power source and clear the stored values from before the ignition switch was turned off.
Turn the ignition switch off and wait for 6 minutes or more.
Make sure that the wire harness(es) and connector(s) for the vehicle being inspected are connected.
After the ignition switch is turned off, the navigation system stores the various memory and settings within approximately 6 minutes. Therefore, make sure to disconnect the cable from the negative (-) battery terminal after confirming that 6 minutes or more have elapsed since turning the ignition switch off.
Disconnect the cable from the negative (-) battery terminal and wait for at least 90 seconds.
Connect the cable to the negative (-) battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Perform the following procedure with the ignition switch ON. (Do not turn the ignition switch to ON (Engine running).)
Turn the ignition switch to ON and wait for 6 minutes or more.
Wait at least 6 minutes for the values of the cooler thermistor (ambient temperature sensor) and thermometer to become stable before taking a measurement.
Measure and make a note of the ambient temperature near the cooler thermistor (ambient temperature sensor) using a thermometer.
Hold the thermometer 50 mm (1.97 in.) from the cooler thermistor (ambient temperature sensor) with its sensing portion at the same height and perpendicular to the cooler thermistor (ambient temperature sensor).
Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.
When measuring the ambient temperature with a thermometer, do not move the thermometer, touch the sensing portion or allow it to contact the vehicle body.
Make a note of the ambient temperature displayed on the multi-information display in the combination meter assembly.
Compare the values of the ambient temperature measured by the thermometer and the cooler thermistor (ambient temperature sensor).
The values of the ambient temperature measured by the thermometer and the cooler thermistor (ambient temperature sensor) are almost the same.
| Proceed to |
|---|
| OK |
| NG |
OK
NG