Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for V35A-FTS)
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467935 COMPRESSOR(for V35A-FTS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for V35A-FTS)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E464859N02
5.938,2.896 7.021,3.125 1.083,0.229 5.99,1.469 7.073,1.698 1.083,0.229 6,4.573 7.083,4.802 1.083,0.229 3.552,4.042 4.229,4.25 0.677,0.208 4.781,3.302 5.583,3.521 0.802,0.219 5.188,3.75 5.99,3.969 0.802,0.219 2.365,1.729 3.073,1.938 0.708,0.208 2.313,1.688 3.125,1.979 0.813,0.292 0.188,1.021 0.865,1.229 0.677,0.208 0.177,0.156 1.156,0.375 0.979,0.219 0.271,1.979 1.25,2.198 0.979,0.219 3.854,1.104 4.26,1.104 false 2.229,4.49 2.698,4.49 false 4.052,5.156 4.604,5.156 false 4.729,1.833 4.906,1.833 4.906,1.833 5.115,2.094 false 3.708,2.792 3.427,2.792 3.427,2.792 3.26,3.229 false 5.698,2.406 6.042,2.406 false 5.219,2.521 5,2.521 5,2.521 4.938,2.729 false 5.219,4.604 5,4.604 5,4.604 4.938,4.813 false 6.26,0.188 6.781,0.188 false 5.948,3.01 5.813,3.01 5.813,3.01 5.813,2.813 false 5.99,1.583 5.75,1.583 false 5.99,4.688 5.781,4.688 false 4.24,4.146 4.385,4.146 4.385,4.146 4.385,3.948 false 4.417,3.656 4.417,3.417 4.417,3.417 4.781,3.417 false 4.813,4.104 4.813,3.865 4.813,3.865 5.177,3.865 false 1.542,0.854 1.75,0.625 1.75,0.625 1.917,0.625 false 2.719,1.5 2.719,1.729 false 1.677,1.74 1.771,1.458 1.771,1.458 1.958,1.458 false 1.823,1.865 1.823,2.083 1.823,2.083 1.26,2.083 false 1.521,1.729 1.521,2.083 false 0.865,1.125 1.094,1.125 false 1.448,0.49 1.448,0.26 1.448,0.26 1.156,0.26 false 4.49,3.594 4.948,3.792 0.458,0.198 10 false x 2 4.563,3.885 5.021,4.083 0.458,0.198 10 false x 2 4.917,4.073 5.375,4.271 0.458,0.198 10 false x 2 5.271,4.51 5.427,4.708 0.156,0.198 10 false ● 5.26,2.417 5.417,2.615 0.156,0.198 10 false ● 6.104,2.302 6.26,2.5 0.156,0.198 10 false ● 2.75,4.354 2.969,4.75 0.219,0.396 18 false 9 4.281,1.708 4.833,2.052 0.552,0.344 18 false 4, 6 4.521,0.958 4.74,1.354 0.219,0.396 18 false 5 3.823,5.01 4.042,5.406 0.219,0.396 18 false 3 4.01,2.646 4.229,3.042 0.219,0.396 18 false 2 6.115,0.031 6.333,0.427 0.219,0.396 18 false 1 6.063,4.604 7.115,4.813 1.052,0.208 8 false 9.8 (100, 87 in.*lbf) 6.063,1.5 7.115,1.708 1.052,0.208 8 false 9.8 (100, 87 in.*lbf) 6,2.927 7.052,3.135 1.052,0.208 8 false 9.8 (100, 87 in.*lbf) 3.615,4.063 4.969,4.219 1.354,0.156 8 false 10 (102, 7) 4.844,3.323 6.563,3.479 1.719,0.156 8 false 24.5 (250, 18) 5.24,3.781 6.958,3.938 1.719,0.156 8 false 24.5 (250, 18) 2.802,1.448 3.26,1.646 0.458,0.198 10 false x 2 2.167,0.469 2.385,0.865 0.219,0.396 18 false 8 2.417,1.75 3.885,1.906 1.469,0.156 8 false 21 (214, 15) 2.219,1.271 2.438,1.667 0.219,0.396 18 false 7 1.188,1.094 1.646,1.292 0.458,0.198 10 false x 2 0.26,1.042 1.615,1.198 1.354,0.156 8 false 10 (102, 7) 0.219,0.188 1.573,0.344 1.354,0.156 8 false 6.3 (64, 56 in.*lbf) 0.313,2 1.667,2.156 1.354,0.156 8 false 6.3 (64, 56 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ADJUST COMPRESSOR OIL - (Click here) - -
2 COMPRESSOR WITH MAGNET CLUTCH - (Click here) - -
3 NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 88711 (Click here) - -
4 INSTALL SUCTION HOSE SUB-ASSEMBLY 88704 (Click here) - -
5 VANE PUMP ASSEMBLY 44310 (Click here) - -
6 CONNECT SUCTION HOSE SUB-ASSEMBLY 88704 (Click here) - -
7 NO. 3 AIR HOSE 17343N (Click here) - -
8 NO. 2 AIR TUBE ASSEMBLY - (Click here) - -
9 RADIATOR WITH COOLER CONDENSER ASSEMBLY - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Compressor oil ND-OIL 8 or equivalent

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E471536C01
1.354,1.063 1.635,1.417 0.281,0.354 18 false i 4.135,0.51 4.51,0.75 0.375,0.24 12 false *A 4.156,1.531 4.531,1.771 0.375,0.24 12 false *A 4.135,2.594 4.51,2.833 0.375,0.24 12 false *B
*A for Type A *B for Type B


i.

When replacing the compressor with magnet clutch with a new one, gradually discharge the inert gas (helium) from the service valve, and drain the following amount of oil before installation.

Standard:
for Type A:

(The amount of oil in a new cooler compressor assembly: 135 to 150 cc (4.57 to 5.07 fl.oz)) - (The amount of oil in the removed cooler compressor assembly) = (The amount of oil to be removed from the new cooler compressor assembly)


Standard:
for Type B:

(The amount of oil in a new cooler compressor assembly: 180 to 195 cc (6.09 to 6.59 fl.oz)) - (The amount of oil in the removed cooler compressor assembly) = (The amount of oil to be removed from the new cooler compressor assembly)


NOTICE:
·

If a new cooler compressor assembly is installed without removing the same amount of compressor oil as is remaining in the pipes, the amount of compressor oil will be excessive. This prevents heat exchange in the refrigerant cycle and will cause the air conditioning system to malfunction.

·

A certain amount of compressor oil remains in the cooler compressor assembly during circulation and the compressor may be damaged if the amount of compressor oil is more/less than this amount. Therefore, make sure to adjust the amount of compressor oil correctly.

·

If the amount of compressor oil remaining in the removed cooler compressor assembly is excessively low, check for compressor oil leaks.

·

Do not race the engine before replacing the cooler compressor assembly.

·

Make sure to use ND-OIL 8 or equivalent compressor oil.





Hide 2.INSTALL COMPRESSOR WITH MAGNET CLUTCH

a.
E460159N01
0.396,0.094 0.583,0.375 0.188,0.281 18 true i 5.677,0.094 5.833,0.292 0.156,0.198 10 true 1 6.115,1.344 6.271,1.542 0.156,0.198 10 true 2 6.25,0.219 6.406,0.417 0.156,0.198 10 true 3 5.677,1.542 5.833,1.74 0.156,0.198 10 true 4

i.

Install the compressor with magnet clutch using the following procedure.

1. Using an E8 "TORX" socket wrench, temporarily install the compressor with magnet clutch with the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

2. Install the compressor with magnet clutch with the 2 bolts and 2 nuts in the order shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)



Hide 88711 3.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E460160N01
0.479,0.073 0.76,0.427 0.281,0.354 18 false i

i.

Install the No. 1 cooler refrigerant discharge hose using the following procedure.

1. Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and connecting part of the compressor with magnet clutch and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose.

Compressor Oil:

ND-OIL 8 or equivalent


2. Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.


3. Install the No. 1 cooler refrigerant discharge hose to the compressor with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)




Hide 88704 4.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.
E460161N01
0.49,0.188 0.771,0.542 0.281,0.354 18 false i 4.063,0.177 4.344,0.531 0.281,0.354 18 false ii 4.302,2.677 4.521,2.958 0.219,0.281 18 true iii 2.531,2.677 2.75,2.958 0.219,0.281 18 true iv

i.

Remove the vinyl tape from the suction hose sub-assembly and connecting part of the compressor with magnet clutch and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



ii.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iii.

Install the suction hose sub-assembly to the compressor with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)



iv.

Connect the connector.



Hide 44310 5.CONNECT VANE PUMP ASSEMBLY

a.
E465791N01
4.677,0.271 4.823,0.583 0.146,0.313 18 true i 0.802,0.073 1.271,0.385 0.469,0.313 18 true ii, iii 1.76,1.677 1.927,1.896 0.167,0.219 10 true 1 2.458,2.146 2.625,2.365 0.167,0.219 10 true 2

i.

Connect the 2 connectors.


ii.

Temporarily install the vane pump assembly with the 2 bolts.


iii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



Hide 88704 6.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E460162N01
0.427,0.073 0.708,0.427 0.281,0.354 18 false i

i.

Connect the suction hose sub-assembly using the following procedure.

1. Remove the vinyl tape from the suction hose sub-assembly and connecting part of the No. 3 air conditioning tube and accessory assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent


2. Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.


3. Connect the suction hose sub-assembly to the compressor with magnet clutch with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)




Hide 17343N 7.INSTALL NO. 3 AIR HOSE

Z101186

Click here(Click here)

Hide 8.INSTALL NO. 2 AIR TUBE ASSEMBLY

Z101186

Click here(Click here)

Hide 9.INSTALL RADIATOR WITH COOLER CONDENSER ASSEMBLY