Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 1GR-FE)
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467940 COMPRESSOR(for 1GR-FE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GR-FE)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E460137N01
3.573,2.167 3.896,2.167 3.896,2.167 4.156,2.49 false 2.052,0.552 2.448,0.552 2.448,0.552 2.74,0.833 false 4.719,1.25 4.906,1.448 4.906,1.448 5.167,1.448 false 5.021,4.667 4.771,5.042 4.771,5.042 4.531,5.042 false 4.01,0.396 4.26,0.396 4.26,0.396 4.406,0.646 false 5.563,3.927 5.417,3.927 5.417,3.927 5.333,4.177 false 2.125,1.938 1.781,1.938 1.781,1.938 1.604,2.323 false 5.365,2.865 5.823,3.063 0.458,0.198 10 false x 2 5.719,3.375 6.177,3.573 0.458,0.198 10 false x 2 5.385,3.177 5.844,3.375 0.458,0.198 10 false x 2 3.885,0.302 4.042,0.5 0.156,0.198 10 false โ— 5.604,3.833 5.76,4.031 0.156,0.198 10 false โ— 1.896,0.406 2.177,0.76 0.281,0.354 18 false 1 2.177,1.781 2.458,2.135 0.281,0.354 18 false 2 4.302,4.896 4.583,5.25 0.281,0.354 18 false 4 5.469,1.323 5.75,1.677 0.281,0.354 18 false 3 3.365,2.031 3.646,2.385 0.281,0.354 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 GENERATOR ASSEMBLY WITH REGULATOR 27060 - - -
2 RADIATOR WITH COOLER CONDENSER ASSEMBLY - - - -
3 SUCTION HOSE SUB-ASSEMBLY 88704 (Click here) - -
4 NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 88711 (Click here) - -
5 COMPRESSOR WITH MAGNET CLUTCH - (Click here) - -

โ— Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the compressor with magnet clutch removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Parking assist monitor system (Click here)
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (Click here)

HINT:
ยท

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 27060 1.REMOVE GENERATOR ASSEMBLY WITH REGULATOR

Hide 2.REMOVE RADIATOR WITH COOLER CONDENSER ASSEMBLY

Hide 88704 3.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E460138N01
4.406,0.073 4.688,0.427 0.281,0.354 18 false iii 0.844,1.083 1,1.365 0.156,0.281 18 true i 2.021,0.385 2.177,0.667 0.156,0.281 18 true ii

i.

Disconnect the connector.


ii.

Remove the bolt and disconnect the suction hose sub-assembly.


iii.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




Hide 88711 4.REMOVE NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E460139N01
0.573,0.083 0.708,0.375 0.135,0.292 18 true i 4.396,0.083 4.583,0.365 0.188,0.281 18 false ii

i.

Remove the bolt and No. 1 cooler refrigerant discharge hose.


ii.

Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.




Hide 5.REMOVE COMPRESSOR WITH MAGNET CLUTCH

a.
E460140C01
5.24,0.906 5.396,1.208 5.396,1.208 5.635,1.208 true 1.354,0.115 1.49,0.396 0.135,0.281 18 true i 4.469,0.219 4.615,0.49 0.146,0.271 18 true ii 3.406,0.198 3.625,0.396 0.219,0.198 10 true *a 3.26,1.406 3.479,1.604 0.219,0.198 10 true *b 5.635,1.104 5.854,1.302 0.219,0.198 10 true *b
*a Bolt (A) *b Bolt (B)


i.

Remove the bolt (A) and 2 nuts.


ii.

Loosen the bolt (B).



b.
E460141C01
6.229,1.354 6.365,1.552 6.365,1.552 6.542,1.552 true 0.75,0.094 0.885,0.375 0.135,0.281 18 true i 4.375,0.094 4.656,0.448 0.281,0.354 18 false ii 6.573,1.469 6.885,1.667 0.313,0.198 10 false *a
*a Bolt (B) - -


i.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with magnet clutch.


ii.

Remove the bolt (B).