Home › Vehicle Exterior › LIGHTING (EXT) › SIDE TURN SIGNAL LIGHT ASSEMBLY
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468049 SIDE TURN SIGNAL LIGHT ASSEMBLY A

LIGHTING (EXT)  SIDE TURN SIGNAL LIGHT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E468156N02
3.969,1 4.271,0.802 4.271,0.802 4.604,0.802 false 4.635,0.635 4.917,0.99 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 OUTER REAR VIEW MIRROR ASSEMBLY LH 87940 - - -

E472975N02
4.875,1.063 5.458,1.063 false 5.24,2.021 5.823,2.021 false 1.26,4.24 1.26,3.76 false 4.542,3.24 4.729,3.688 4.729,3.688 5.073,3.688 false 5.063,1.885 5.344,2.24 0.281,0.354 18 false 2 1.188,4.26 1.469,4.615 0.281,0.354 18 false 3 5.448,3.563 5.729,3.917 0.281,0.354 18 false 4 5.531,0.948 5.813,1.302 0.281,0.354 18 false 5 2.719,2.99 3.177,3.188 0.458,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 OUTER MIRROR LH 87961 - - -
3 OUTER MIRROR COVER LH 87945 (Click here) - -
4 COVER BODY - (Click here) - -
5 SIDE TURN SIGNAL LIGHT ASSEMBLY LH 81740 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the side turn signal light assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
·

Side television camera assembly LH (Including removal and installation)

·

Side television camera assembly RH (Including removal and installation)

·

Outer rear view mirror assembly with cover LH (Including removal and installation)

·

Outer rear view mirror assembly with cover RH (Including removal and installation)


Side television camera view adjustment Panoramic view monitor system (Click here)
·

Front television camera assembly, front bumper assembly or radiator grille

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


·

Television camera view adjustment

HINT:

Replacement or removal and installation of 2 or more parts


·

Rear television camera view adjustment (for Rear camera detection system)



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 87940 1.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 87945 3.REMOVE OUTER MIRROR COVER LH

Z101186

(Click here)

Hide 4.REMOVE COVER BODY

a.
E472977C02
0.427,0.375 0.708,0.729 0.281,0.354 18 false i 4.01,0.271 4.635,0.604 0.625,0.333 18 false ii 0.521,2.688 1.146,3.021 0.625,0.333 18 false iii 3.979,2.771 4.604,3.104 0.625,0.333 18 false iv
V100135

Move in this Direction
V100144

Protective Tape
V100145

Vinyl Tape - -


i.

Apply protective tape as shown in the illustration.


ii.

Move the outer rear view mirror assembly LH to the forward position.


iii.

Detach the clamp.


iv.

Remove the vinyl tape.



b.
E472978C01
4.458,0.229 4.74,0.583 0.281,0.354 18 false ii 0.542,2.719 0.823,3.073 0.281,0.354 18 false iii 0.573,0.271 0.854,0.625 0.281,0.354 18 false i
V113146

Place Hand Here
V113147

Pull in this Direction (1)
V113148

Pull in this Direction (2)


i.

Pull the harness sub-assembly and the television camera wire as shown in the illustration.


ii.

Remove the 4 screws.


iii.

Detach the claw and pull out the cover body as shown in the illustration.



Hide 81740 5.REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

a.
E472979C01
0,0 0,0 false
V113147

Remove in this Direction
V100135

Connector