Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD)
RM38G0E _59 Vehicle Exterior _100887 DOOR / HATCH _0468205 FUEL LID LOCK CONTROL CABLE ASSEMBLY(for LHD) A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B627874N01
0.167,3.906 2,5.667 1.833,1.76 2.917,0.594 3.25,0.594 false 5.469,1.083 5.802,1.083 false 4.969,3.385 5.302,3.385 false 4.094,4.917 4.427,4.917 false 1.063,5.01 1.313,5.01 false 0.844,3.167 1.177,3.167 false 4.167,2.833 4.5,2.833 false 0.573,2.167 0.906,2.167 false 2.479,2.885 2.813,2.885 false 5.25,0.948 5.531,1.302 0.281,0.354 18 false 1 0.625,3.052 0.906,3.406 0.281,0.354 18 false 4 5.406,3.26 5.688,3.615 0.281,0.354 18 false 6 3.844,4.792 4.125,5.146 0.281,0.354 18 false 2 1.01,2.042 1.292,2.396 0.281,0.354 18 false 5 3.635,0.479 3.917,0.833 0.281,0.354 18 false 3 4.615,2.729 4.896,3.083 0.281,0.354 18 false 7 2.24,2.771 2.521,3.125 0.281,0.354 18 false 8 2.99,1.01 3.302,1.208 0.313,0.198 10 false x2 1.302,4.125 1.615,4.323 0.313,0.198 10 false x4 1.667,4.896 1.948,5.25 0.281,0.354 18 false 9 0.25,4 0.625,4.24 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT SEAT ASSEMBLY LH - - - -
2 QUARTER TRIM PANEL ASSEMBLY LH 62520B - - -
3 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 (Click here) - -
4 FRONT DOOR SCUFF PLATE LH 67914B - - -
5 COWL SIDE TRIM BOARD LH 62112 - - -
6 OUTER LAP BELT ANCHOR COVER 73233 - - -
7 FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) 73220 - - -
8 CENTER PILLAR LOWER GARNISH LH 62414A - - -
9 NO. 1 SPEAKER WITH BOX ASSEMBLY 86150 (Click here) - -

*A w/ Woofer - -

B628043N01
3.875,0.531 4.208,0.531 false 2.417,0.833 2.75,0.833 false 1.656,5.156 1.99,5.156 false 5.271,2.208 5.271,1.875 false 3.729,2.708 4.063,2.708 false 4.406,2.542 4.958,2.896 0.552,0.354 18 false 12 2.063,0.719 2.438,1.063 0.375,0.344 18 false 13 5.135,2.24 5.51,2.583 0.375,0.344 18 false 10 2.031,5.073 2.344,5.271 0.313,0.198 10 false *1 4.292,0.396 4.667,0.74 0.375,0.344 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

10 FUEL FILLER OPENING LID LOCK RETAINER 77377 - - -
11 FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY 77306 - - -
12 FRONT FLOOR CARPET ASSEMBLY 58510D (Click here) - -
13 FUEL LOCK CONTROL CABLE SUB-ASSEMBLY 77035 - - -

*1 NO. 2 FLOOR CARPET WELT LH - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the fuel lid lock control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY LH

Hide 62520B 2.REMOVE QUARTER TRIM PANEL ASSEMBLY LH

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 73233 6.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 7.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 8.REMOVE CENTER PILLAR LOWER GARNISH LH

Hide 86150 9.REMOVE NO. 1 SPEAKER WITH BOX ASSEMBLY (w/ Woofer)

Z101186

Click here(Click here)

Hide 77377 10.REMOVE FUEL FILLER OPENING LID LOCK RETAINER

a.
B609500C03
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 77306 11.DISCONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
B610153


Hide 58510D 12.SEPARATE FRONT FLOOR CARPET ASSEMBLY

a.
B628044N01
1.958,0.052 2.24,0.406 0.281,0.354 18 false i

i.

Peel back the front floor carpet assembly as shown in the illustration.



Hide 77035 13.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

a.
B610155


b.
B610156