CHECK MULTIPLEX NETWORK DOOR ECU
Disconnect the T4, T3, T2 and T1 multiplex network door ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T1-9 (IG) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| T1-7 (ECUB) - Body ground | Battery power supply | Always | 11 to 14 V |
| T4-5 (B) - Body ground | Battery power supply | Always | 11 to 14 V |
| T3-4 (GND) - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the T4, T3, T2 and T1 multiplex network door ECU connectors.
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T2-13 (DS1) - Body ground | Power back door unit assembly LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation (See waveform 1) |
||
| T2-5 (DS2) - Body ground | Power back door unit assembly LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation (See waveform 2) |
||
| T2-6 (DS12) - Body ground | Power back door unit assembly RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation (See waveform 1) |
||
| T2-12 (DS22) - Body ground | Power back door unit assembly RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation (See waveform 2) |
||
| T2-3 (DV2) - Body ground | Power back door unit assembly RH (door sensor) power supply | Always | 7 V or higher |
| T2-8 (OSR) - T2-9 (OSE) | Power back door sensor assembly RH signal | Power back door sensor assembly RH not pressed | 4 to 6 V |
| Power back door sensor assembly RH pressed | Below 1 V | ||
| T1-14 (BDDN) - Body ground | Door control switch assembly signal | Door control switch assembly on | Below 1 V |
| Door control switch assembly off | Pulse generation | ||
| T1-4 (CLSW) - Body ground | Door control switch signal | Door control switch on | Below 1 V |
| Door control switch off | 11 to 14 V | ||
| T3-1 (CTYO) - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | ||
| T1-1 (BZR+) - Body ground | Power back door warning buzzer signal | Power back door warning buzzer sounding | Pulse generation |
| Power back door warning buzzer not sounding | Below 1 V | ||
| T2-10 (DSG2) - Body ground | Power back door unit assembly RH (door sensor) ground | Always | Below 1 V |
| T2-11 (DSG) - Body ground | Power back door unit assembly LH (door sensor) ground | Always | Below 1 V |
| T2-4 (DSV) - Body ground | Power back door unit assembly LH (door sensor) power supply | Always | 7 V or higher |
| T2-1 (OSL) - T2-9 (OSE) | Power back door sensor assembly LH signal | Power back door sensor assembly LH not pressed | 4 to 6 V |
| Power back door sensor assembly LH pressed | Below 1 V | ||
| T3-2 (DC+) - T3-6 (DC-) | Back door lock assembly (back door lock motor) circuit | Back door lock motor operating | 11 to 14 V |
| Back door lock motor not operating | Below 1 V |
Using an oscilloscope, check waveform 1.
| Item | Condition |
|---|---|
| Tester Connection |
·
T2-13 (DS1) - Body ground
·
T2-6 (DS12) - Body ground |
| Tool Setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle Condition | Power back door operating |
The period changes in accordance to the speed at which the power back door is opened and closed.
Using an oscilloscope, check waveform 2.
| Item | Condition |
|---|---|
| Tester Connection |
·
T2-5 (DS2) - Body ground
·
T2-12 (DS22) - Body ground |
| Tool Setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle Condition | Power back door operating |
The period changes in accordance to the speed at which the power back door is opened and closed.
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A-26 (BECU) - Body ground | Battery power supply | Always | 11 to 14 V |
| A-27 (IGR) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| A-13 (GND1) - Body ground | Body ground | Always | Below 1 Ω |
| A-14 (GND2) - Body ground | Body ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 5F-2 (BCTY) - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | ||
| I2-21 (PBDS) - Body ground | Power back door control switch signal | Power back door control switch off | Pulse generation |
| Power back door control switch on | Below 1 V | ||
| 5F-2 (BCTY) - Body ground | Back door courtesy light switch input | Back door closed | Below 1 V |
| Back door open | Pulse generation |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)