Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468606 ADAPTIVE HIGH BEAM SYSTEM J

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  Adaptive High Beam Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the ON/OFF signal of the auto high beam switch.

WIRING DIAGRAM

E400733E06
1.5,0.948 1.854,1.156 0.354,0.208 10 false 2 1.698,0.958 2.052,1.167 0.354,0.208 10 false E 2.865,0.948 3.219,1.156 0.354,0.208 10 false +B 3.156,0.948 3.51,1.156 0.354,0.208 10 false 5 1.667,1.573 1.906,1.74 0.24,0.167 10 false I81 1.667,1.74 3.396,2.198 1.729,0.458 10 false Auto High Beam Switch 4.969,1.844 5.167,2.021 0.198,0.177 10 false I3 4.979,2.021 6.635,2.448 1.656,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.313,0.938 5.667,1.146 0.354,0.208 10 false AHBI 5.948,0.646 6.302,0.854 0.354,0.208 10 false +B 5.063,0.938 5.417,1.146 0.354,0.208 10 false 14

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal OFF or ON OFF: Auto high beam switch not pressed
ON: Auto high beam switch pressed
-
Body Electrical > Main Body > Data List
Tester Display
Auto High Beam Main Switch
50003 123 274
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT AUTO HIGH BEAM SWITCH
2.INSPECT AUTO HIGH BEAM SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the I81 auto high beam switch connector.


b.

Disconnect the I3 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I81,I3)Location & Routing

Click Connector(I81)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Auto High Beam Switch

Click Connector(I3)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Main Body ECU

I81-5 (+B) - I3-14 (AHBI) Always Below 1 Ω
I81-5 (+B) or I3-14 (AHBI) - Body ground Always 10 kΩ or higher
I81-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR