Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0468606 ADAPTIVE HIGH BEAM SYSTEM T

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>REGISTRATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

Sequential Recognition:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

One Time Recognition:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Driving Adjustment:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT


·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT




HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.


Adaptive High Beam System
Symptom Suspected Area Link
Adaptive high beam indicator on the combination meter assembly does not illuminate Check operating conditions Click here
Meter / gauge system Click here
Adaptive high beam switch circuit Click here
Headlight dimmer switch circuit Click here
Combination meter assembly Click here
Forward recognition camera Click here
Headlight ECU sub-assembly LH Click here
Adaptive high beam system does not operate Customize settings Click here
Check operating conditions Click here
Check that the low beams and high beams operate manually -
Check automatic light control system operation Click here
Adaptive high beam switch circuit Click here
Headlight dimmer switch circuit Click here
Forward recognition camera Click here
Millimeter wave radar sensor assembly Click here
Light control LED ECU Click here
Headlight ECU sub-assembly LH Click here
Adaptive high beam switch indicator does not come ON Refer to "Adaptive High Beam Switch Indicator does not Come ON" Click here