Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU)
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  Front Fog Light Circuit  


DESCRIPTION

The power distribution box assembly controls the front fog lights.

WIRING DIAGRAM

w/ Cornering light
E466697E01
2.865,1.448 5.229,1.646 2.365,0.198 10 false Semiconductor Power Integration ECU 2.885,1.281 5.302,2.271 2.417,0.99 10 false B57 4.479,0.813 6.896,1.802 2.417,0.99 10 false 17 4.292,0.927 4.49,1.115 0.198,0.188 10 false L 1.26,2.969 3.677,3.958 2.417,0.99 10 false Fog Light LED LH 1.281,4.698 3.698,5.688 2.417,0.99 10 false Fog Light LED RH 0.667,5.281 2.396,5.5 1.729,0.219 10 false : CXPI Communication Line 5.5,1.542 6.635,3 1.135,1.458 10 false Power Distribution Box Assembly 3.01,2.979 5.427,3.969 2.417,0.99 10 false Fog Light Light Unit LH 2.99,4.677 5.406,5.667 2.417,0.99 10 false Fog Light Light Unit RH 3,4.521 5.406,5.469 2.406,0.948 10 false A8 3.01,2.813 5.427,3.802 2.417,0.99 10 false A7 4.448,2.104 4.583,2.313 0.135,0.208 10 false 1 4.458,3.771 4.594,3.927 0.135,0.156 10 false 1 4.448,2.396 6.865,3.385 2.417,0.99 10 false 4 4.469,4.073 4.635,4.281 0.167,0.208 10 false 4 4.198,3.781 4.375,3.99 0.177,0.208 10 false B 4.219,2.115 4.365,2.333 0.146,0.219 10 false B 4.219,2.406 4.375,2.583 0.156,0.177 10 false E 4.208,4.073 4.354,4.281 0.146,0.208 10 false E 1.271,4.521 3.688,5.51 2.417,0.99 10 false B 1.292,2.813 3.708,3.802 2.417,0.99 10 false A 2.521,2.406 4.938,3.396 2.417,0.99 10 false 1 2.531,2.115 4.948,3.104 2.417,0.99 10 false 2 2.521,3.802 4.938,4.792 2.417,0.99 10 false 2 2.521,4.083 4.938,5.073 2.417,0.99 10 false 1

w/o Cornering light
E466701E01
2.865,1.448 5.281,2.438 2.417,0.99 10 false Semiconductor Power Integration ECU 2.885,1.281 5.302,2.271 2.417,0.99 10 false B57 4.479,0.813 6.896,1.802 2.417,0.99 10 false 17 4.281,0.927 4.51,1.135 0.229,0.208 10 false L 2.604,3.198 5.021,4.188 2.417,0.99 10 false Fog Light LED LH 2.646,4.896 5.073,5.594 2.427,0.698 10 false Fog Light LED RH 0.76,5.271 2.479,5.479 1.719,0.208 10 false : CXPI Communication Line 5.5,1.542 6.635,3 1.135,1.458 10 false Power Distribution Box Assembly 2.594,4.729 5,5.677 2.406,0.948 10 false A2 2.542,3.031 4.958,4.021 2.417,0.99 10 false A1 4.063,2.563 4.219,2.771 0.156,0.208 10 false 1 4.063,4.281 6.479,5.271 2.417,0.99 10 false 1 4.073,2.219 4.188,2.458 0.115,0.24 10 false 2 4.063,3.958 4.229,4.167 0.167,0.208 10 false 2 3.802,3.958 3.948,4.146 0.146,0.188 10 false B 3.792,2.229 3.948,2.458 0.156,0.229 10 false B 3.792,2.573 4,2.75 0.208,0.177 10 false E 3.802,4.302 3.969,4.51 0.167,0.208 10 false E

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Input Signal Front fog light input OFF or ON OFF: Front fog lights off
ON: Front fog lights on
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Input Signal
50003 473 414
OK:

Display changes according to the front fog light switch operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Output Signal Front fog light output OFF or ON OFF: Front fog lights off
ON: Front fog lights on
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Output Signal
50003 473 415
OK:

Display changes according to the front fog light switch operation.



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

3.CHECK VEHICLE TYPE
Result:
Result Proceed to
w/o Cornering light A
w/ Cornering light B



A

4.READ VALUE USING GTS

B

11.READ VALUE USING GTS
4.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)

NG

7.READ VALUE USING GTS
5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A1 fog light LED LH connector.


c.

Disconnect the A2 fog light LED RH connector.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A1,A2)Location & Routing

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A1-1 (E) - Body ground Always Below 1 Ω
A2-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS
a.

Disconnect the A1 fog light LED LH connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

8.READ VALUE USING GTS
8.READ VALUE USING GTS
a.

Reconnect the A1 fog light LED LH connector.


b.

Disconnect the A2 fog light LED RH connector.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A1 fog light LED LH connector.


c.

Disconnect the A2 fog light LED RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B57,A1,A2)Location & Routing

Click Connector(B57)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Semiconductor Power Integration ECU

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

B57-17 (L) or A1-2 (B) - Other terminals and body ground Always 10 kΩ or higher
B57-17 (L) or A2-2 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A1,A2)Location & Routing

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A1-1 (E) - Other terminals and body ground Always Below 1 Ω
A2-1 (E) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LIGHT UNIT)

NG

14.READ VALUE USING GTS
12.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LIGHT UNIT)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A7 fog light light unit LH connector.


c.

Disconnect the A8 fog light light unit RH connector.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FOG LIGHT LIGHT UNIT - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (FOG LIGHT LIGHT UNIT - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A7,A8)Location & Routing

Click Connector(A7)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A8)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A7-4 (E) - Body ground Always Below 1 Ω
A8-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS
a.

Disconnect the A7 fog light light unit LH connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

15.INSPECT FOG LIGHT LIGHT UNIT LH

NG

16.READ VALUE USING GTS
15.INSPECT FOG LIGHT LIGHT UNIT LH
a.

Disconnect the A fog light LED LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A7)Location & Routing

Click Connector(A7)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

A-2 or A7-1 (B) - Other terminals and body ground Always Below 1 Ω
A-1 or A7-4 (E) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE FOG LIGHT LIGHT UNIT LH

16.READ VALUE USING GTS
a.

Reconnect the A7 fog light light unit LH connector.


b.

Disconnect the A8 fog light light unit RH connector.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

17.INSPECT FOG LIGHT LIGHT UNIT RH

NG

18.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LIGHT UNIT)
17.INSPECT FOG LIGHT LIGHT UNIT RH
a.

Disconnect the B fog light LED RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

B-1 or A8-1 (B) - Other terminals and body ground Always Below 1 Ω
B-2 or A8-4 (E) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE FOG LIGHT LIGHT UNIT RH

18.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LIGHT UNIT)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A7 fog light light unit LH connector.


c.

Disconnect the A8 fog light light unit RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B57,A7,A8)Location & Routing

Click Connector(B57)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Semiconductor Power Integration ECU

Click Connector(A7)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A8)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

B57-17 (L) or A7-1 (B) - Other terminals and body ground Always Below 1 Ω
B57-17 (L) or A8-1 (B) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (FOG LIGHT LIGHT UNIT - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (FOG LIGHT LIGHT UNIT - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A7,A8)Location & Routing

Click Connector(A7)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A8)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A7-4 (E) - Other terminals and body ground Always Below 1 Ω
A8-4 (E) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR