Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467509 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15C111  GNSS Antenna Circuit Short to Ground  B15C113  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C111 GNSS Antenna Circuit Short to Ground Current to the roof antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

Antenna divider

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly


Telematics A
B15C113 GNSS Antenna Circuit Open Current to the roof antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telephone transceiver assembly

·

Roof antenna assembly

·

Antenna divider

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly


Telematics A

WIRING DIAGRAM

E473971E03
3.771,4.323 5.615,4.563 1.844,0.24 10 false Antenna Cord Sub-assembly 5.198,2.917 6.615,3.375 1.417,0.458 10 false Telephone Transceiver Assembly 2.021,0.927 2.198,1.146 0.177,0.219 10 false A 2.031,1.469 2.198,1.656 0.167,0.188 10 false A 3.479,0.927 3.656,1.115 0.177,0.188 10 false B 3.479,1.469 3.677,1.667 0.198,0.198 10 false B 4.958,0.708 5.135,0.906 0.177,0.198 10 false 1 4.917,1.26 5.125,1.49 0.208,0.229 10 false 1a 3.438,3.688 3.677,3.885 0.24,0.198 10 false 5a 4.948,0.917 5.125,1.115 0.177,0.198 10 false D 1.125,1.865 1.99,2.292 0.865,0.427 10 false Roof Antenna Assembly 5.271,0.927 5.635,1.115 0.365,0.188 10 false ANT2 2.021,0.729 2.177,0.927 0.156,0.198 10 false 2 2.01,1.24 2.208,1.438 0.198,0.198 10 false 2a 3.458,0.719 3.615,0.917 0.156,0.198 10 false 2 3.448,1.25 3.646,1.448 0.198,0.198 10 false 2a 4.948,1.469 5.125,1.667 0.177,0.198 10 false D 2.177,1.781 3.406,2.167 1.229,0.385 10 false No. 3 Antenna Cord Sub-assembly 2.323,4.146 3.344,4.344 1.021,0.198 10 false Antenna Divider 3.479,3.177 3.625,3.354 0.146,0.177 10 false 5 3.479,2.198 3.625,2.375 0.146,0.177 10 false 6 3.458,2.677 3.656,2.854 0.198,0.177 10 false 6a 3.469,2.396 3.667,2.594 0.198,0.198 10 false C 3.469,2.875 3.667,3.073 0.198,0.198 10 false C 3.469,3.385 3.667,3.583 0.198,0.198 10 false C 3.469,3.906 3.667,4.104 0.198,0.198 10 false C

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTC are not output. A
DTCs are output. B



Post-procedure1

d.

None



A

B

2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.
E462683C01
0.271,1.031 0.583,1.344 0.313,0.313 0.521,3.542 0.823,3.813 0.302,0.271 1.594,0.969 1.417,0.667 1.417,0.667 1.25,0.667 true 1.708,3.875 2.063,4.313 2.063,4.313 2.219,4.313 true 0.26,0.219 0.573,0.417 0.313,0.198 10 false *a 0.292,1.969 0.604,2.167 0.313,0.198 10 false *b 0.354,1.104 0.667,1.302 0.313,0.198 10 false A 0.625,3.615 0.938,3.813 0.313,0.198 10 false B 1.021,0.552 1.333,0.75 0.313,0.198 10 false 2a 2.281,4.219 2.594,4.417 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the roof antenna assembly connector.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.
E482825C02
1.542,3.135 1.958,3.385 0.417,0.25 1.552,0.125 1.969,0.375 0.417,0.25 1.542,1.781 1.958,2.031 0.417,0.25 2.292,1.583 1.885,1.208 true 1.885,4.146 2.531,3.708 true 2.833,2.073 2.521,2.417 true 2.51,2.083 2.219,2.417 true 1.302,3.875 1.667,4.115 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.167,3.281 0.479,3.479 0.313,0.198 10 false *c 1.719,0.156 2.031,0.354 0.313,0.198 10 false B 2.354,1.51 2.667,1.708 0.313,0.198 10 false 2a 2.573,3.594 2.885,3.792 0.313,0.198 10 false 1a 1.719,3.177 2.031,3.375 0.313,0.198 10 false D 0.177,1.781 0.49,1.979 0.313,0.198 10 false *b 1.719,1.813 2.031,2.01 0.313,0.198 10 false C 2.906,1.969 3.219,2.167 0.313,0.198 10 false 6a 2.51,1.865 2.823,2.063 0.313,0.198 10 false 5a 0.938,3.698 1.333,3.896 0.396,0.198 10 false ANT2
*a Front view of antenna cord sub-assembly connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of antenna cord sub-assembly connector
(to Antenna Divider)
*c Front view of antenna cord sub-assembly connector
(to Telephone Transceiver Assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna connector from the antenna divider connector.


c.

Disconnect the antenna connector from the telephone transceiver assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-6 Always Below 1 Ω
B-2a - C-6a Always Below 1 Ω
C-5 - D-1 (ANT2) Always Below 1 Ω
C-5a - D-1a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher
D-1 (ANT2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

4.INSPECT ANTENNA DIVIDER

NG

4.INSPECT ANTENNA DIVIDER
a.

Remove the antenna divider.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL



b.
E241596C15
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - 5 Always 10 kΩ or higher
5 - 5a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ROOF ANTENNA ASSEMBLY

NG

5.REPLACE ROOF ANTENNA ASSEMBLY

Pre-procedure1

a.

Replace the roof antenna assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL



b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTC are not output. A
DTCs are output. B



Post-procedure1

d.

None



A

END (ROOF ANTENNA ASSEMBLY IS DEFECTIVE)

B

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT