| *1 | FRONT DISC BRAKE ANTI-RATTLE SPRING | *2 | FRONT NO. 1 DISC BRAKE ANTI-SQUEAL SHIM |
| *3 | FRONT NO. 2 DISC BRAKE ANTI-SQUEAL SHIM | *4 | PIN HOLD CLIP |
| *5 | FRONT DISC BRAKE ANTI-RATTLE PIN WITH HOLE | *6 | FRONT DISC BRAKE PAD |
|
Disc Brake Grease (Part No. 08887-80609) | - | - |
Immediately after installing the front disc brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
04945 1.INSTALL FRONT ANTI SQUEAL SHIM KIT
|
|
| *1 | Front Disc Brake Pad | *2 | Front No. 1 Disc Brake Anti-squeal Shim |
| *3 | Front No. 2 Disc Brake Anti-squeal Shim | - | - |
04465 2.INSTALL FRONT DISC BRAKE PAD KIT
Using SST, push back the front disc brake pistons.
Make sure the brake fluid does not overflow from the reservoir.
Do not forcibly push in the front disc brake pistons.
| *a | 17.2 mm (0.677 in.) | - | - |
|
Disc Brake Grease (Part No. 08887-80609) | - | - |
Lightly apply disc brake grease (Part No. 08887-80609) or equivalent to the areas shown in the illustration where the front disc brake pad and disc brake cylinder assembly contact each other.
Install the 2 front disc brake pads to the disc brake cylinder assembly.
04947 3.INSTALL FRONT DISC BRAKE FITTING KIT
|
Front of the Vehicle | - | - |
Temporarily install the front disc brake anti-rattle spring to the front disc brake pads as shown in the illustration.
Install the front disc brake anti-rattle pin with hole (lower side) and set the front disc brake anti-rattle spring to the front disc brake pads.
Set the front disc brake anti-rattle spring so that it does not overlap and ride up onto the disc brake cylinder assembly.
While pressing the front disc brake anti-rattle spring, install the front disc brake anti-rattle pin with hole (upper side).
Install the pin hold clip to the front disc brake anti-rattle pin with hole and engage the hook to the disc brake cylinder assembly.
5.INSPECT BRAKE FLUID LEVEL IN RESERVOIR
6.INSTALL FRONT WHEEL
7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART