Home › General › MAINTENANCE › REAR DISC BRAKE PAD
RM38G0E _V1 General _100461 MAINTENANCE _0468811 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455985N02
5.75,2.5 6.083,2.5 false 6.344,0.615 6.802,0.615 false 6.333,0.208 6.854,0.208 false 6.156,2.385 6.573,2.719 0.417,0.333 18 false 2 6.167,0.083 6.583,0.417 0.417,0.333 18 false 1 6.167,0.49 6.583,0.823 0.417,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR WHEEL - - - -
3 DISABLE BRAKE CONTROL - - - (Click here)

C456309N01
4.75,3.833 5.75,4.833 1,1 3.667,3.167 4.667,4.167 1,1 5.917,4.5 6.917,5.5 1,1 4.5,5 5.417,5.667 0.917,0.667 0.083,0.083 1.5,1.417 1.417,1.333 0.833,0.448 0.833,0.281 0.833,0.281 1.083,0.281 false 5.333,0.771 5.667,0.771 false 5.708,3.417 5.958,3.417 false 3.5,3.552 3.667,3.552 false 6.083,4.5 6.083,4.167 6.083,4.167 6.25,4.167 false 4.333,5.375 4.5,5.375 false 6.198,4.667 6.448,4.667 false 6.417,5.25 6.667,5.25 false 4,3.417 4.25,3.417 false 4.115,4 4.365,4 false 4.75,5.167 4.917,5.167 4.917,5.167 4.917,5.417 false 4.833,5.417 5.167,5.417 false 5.083,4 5.5,4 false 5.417,4 5.417,4.167 false 3.781,1.844 4.281,1.844 true 4.583,4.5 4.75,4.5 false 3,1.24 3,0.99 3,0.99 4,0.99 true 0.521,0.792 0.938,1.042 0.417,0.25 10 false x 2 5.896,2.833 6.313,3.083 0.417,0.25 10 false x 2 1.146,0.156 1.479,0.573 0.333,0.417 18 false 4 5.979,0.646 6.313,1.063 0.333,0.417 18 false 5 6.302,3.302 6.635,3.719 0.333,0.417 18 false 6 4.594,1.729 4.927,2.146 0.333,0.417 18 false 7 3.302,3.427 3.635,3.844 0.333,0.417 18 false 9 6.573,4.052 6.906,4.469 0.333,0.417 18 false 9 4.156,5.24 4.49,5.656 0.333,0.417 18 false 9 3.948,3.938 4.365,4.188 0.417,0.25 10 false *1 4.302,3.354 4.719,3.604 0.417,0.25 10 false *2 6.5,4.604 6.917,4.854 0.417,0.25 10 false *1 6.25,5.188 6.667,5.438 0.417,0.25 10 false *2 4.542,5.344 4.958,5.594 0.417,0.25 10 false ● *3 5.552,3.938 5.969,4.188 0.417,0.25 10 false *4 0.167,0.167 0.5,0.417 0.333,0.25 10 false *A 4.406,4.365 4.74,4.781 0.333,0.417 18 false 8 4.052,0.885 4.469,1.135 0.417,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

4 PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY 46170 - - -
5 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
6 REAR DISC BRAKE DUST BOOT PROTECTOR 47877 (Click here) - -
7 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
8 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
9 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -

*A w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY - -
*1 REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM *2 REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM
*3 REAR DISC BRAKE PAD WEAR INDICATOR PLATE *4 REAR DISC BRAKE PAD
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click here(Click here)




Hide 2.REMOVE REAR WHEEL

Hide 3.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 46170 4.REMOVE PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 47877 6.REMOVE REAR DISC BRAKE DUST BOOT PROTECTOR

a.
C456308N01
0.417,0.042 1.167,0.542 0.75,0.5 18 false i

i.

Using an 8 mm socket wrench, remove the 2 bolts and rear disc brake dust boot protector from the rear disc brake cylinder assembly.



Hide 47850 7.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Z101186

CAUTION:
·
C456310


·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.




a.
C456311


Hide 04466 8.REMOVE REAR DISC BRAKE PAD KIT

Z101186

CAUTION:

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.



a.
C456312


Hide 04946 9.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C456313N01
3.917,0.042 4.25,0.375 0.333,0.333 18 false ii 0.167,0.042 0.5,0.375 0.333,0.333 18 false i

i.

Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.


ii.

Using a screwdriver, remove the rear disc brake pad wear indicator plate from each rear disc brake pad.

NOTICE:

If the rear disc brake pad wear indicator plate is removed, replace it with a new one.