Home › General › MAINTENANCE › REAR DISC BRAKE PAD
RM38G0E _V1 General _100461 MAINTENANCE _0468811 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C456314N04
5.875,4.417 6.875,5.5 1,1.083 4.75,3.75 5.833,4.833 1.083,1.083 3.708,3.083 4.708,4.167 1,1.083 4.5,5 5.5,5.667 1,0.667 6.021,2.448 7.021,2.615 1,0.167 0.333,1.417 1.083,1.583 0.75,0.167 4.333,0.167 5.083,0.333 0.75,0.167 4.292,0.125 5.125,0.375 0.833,0.25 0.083,0.083 1.5,1.75 1.417,1.667 5.333,0.75 5.667,0.75 false 3.542,3.552 3.708,3.552 false 6.083,4.417 6.083,4.167 6.083,4.167 6.25,4.167 false 4.583,4.5 4.75,4.5 false 4.333,5.333 4.5,5.333 false 5.719,3.427 5.969,3.427 false 5.854,2.781 5.854,2.531 5.854,2.531 6.021,2.531 false 0.167,1.5 0.167,0.917 0.167,0.917 0.417,0.917 false 0.167,1.5 0.333,1.5 false 3,1.25 3,0.25 3,0.25 4.083,0.25 true 0.833,0.438 0.833,0.271 0.833,0.271 1,0.271 false 4.115,4 4.365,4 false 6.208,4.667 6.458,4.667 false 6.417,5.25 6.667,5.25 false 4,3.396 4.25,3.396 false 4.833,5.469 5.167,5.469 false 4.75,5.177 5,5.177 5,5.177 5,5.458 false 3.781,1.833 4.281,1.833 true 5.083,4 5.583,4 false 5.417,4 5.417,4.167 false 3.344,3.427 3.677,3.76 0.333,0.333 18 false 1 6.531,4.042 6.865,4.375 0.333,0.333 18 false 1 4.427,4.354 4.76,4.688 0.333,0.333 18 false 2 4.135,5.219 4.469,5.552 0.333,0.333 18 false 1 4.583,1.719 4.917,2.052 0.333,0.333 18 false 3 6.302,3.292 6.719,3.625 0.417,0.333 18 false 4 5.865,2.833 6.198,3.083 0.333,0.25 10 false x 2 6.073,2.469 7.156,2.719 1.083,0.25 8 false 7.9 (81, 70 in.*lbf) 0.5,0.75 0.833,1 0.333,0.25 10 false x 2 0.406,1.438 1.49,1.688 1.083,0.25 8 false 20 (204, 15) 4.406,0.188 5.323,0.521 0.917,0.333 8 false 55 (561, 41) 5.958,0.635 6.375,0.969 0.417,0.333 18 false 5 1.052,0.146 1.469,0.479 0.417,0.333 18 false 6 3.958,3.927 4.292,4.177 0.333,0.25 10 false *1 6.51,4.604 6.844,4.854 0.333,0.25 10 false *1 6.24,5.188 6.573,5.438 0.333,0.25 10 false *2 4.302,3.333 4.635,3.583 0.333,0.25 10 false *2 4.563,5.385 4.896,5.635 0.333,0.25 10 false ● *3 0.167,0.167 0.5,0.417 0.333,0.25 10 false *A 5.635,3.938 5.969,4.188 0.333,0.25 10 false *4 4.135,0.156 4.385,0.406 0.25,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -
2 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
3 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
4 REAR DISC BRAKE DUST BOOT PROTECTOR 47877 (Click here) - -
5 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
6 PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY 46170 - - -

*A w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY - -
*1 REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM *2 REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM
*3 REAR DISC BRAKE PAD WEAR INDICATOR PLATE *4 REAR DISC BRAKE PAD
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part - -

C457776N01
6.427,1.083 6.844,1.083 false 5.75,2.5 6.167,2.5 false 6.427,0.198 6.875,0.198 false 6.417,0.656 6.802,0.656 false 6.135,0.531 6.615,0.896 0.479,0.365 18 false 10 6.229,2.375 6.479,2.708 0.25,0.333 18 false 9 6.229,0.063 6.646,0.396 0.417,0.333 18 false 7 6.24,0.969 6.656,1.302 0.417,0.333 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

7 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - (Click here) - -
8 INSPECT BRAKE FLUID LEVEL IN RESERVOIR - - (Click here) -
9 REAR WHEEL - - - -
10 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Z101186

NOTICE:
·

When replacing worn rear disc brake pads, the rear disc brake anti-squeal shims and rear disc brake pad wear indicator plates must be replaced together with the rear disc brake pads.

·

Install each rear disc brake pad wear indicator plate in the correct position and direction.

·

Install the rear disc brake anti-squeal shims in the correct positions and directions.




a.
C456315C01
2.25,0.25 2.5,0.25 false 4.708,1.583 4.958,1.583 false 2.917,0.333 2.917,0.167 2.917,0.167 3.167,0.167 false 4.125,1.083 4.125,0.917 4.125,0.917 4.375,0.917 false 3.021,1.667 3.604,1.667 false 3.229,1.667 3.229,1.448 false 3.219,0.104 3.552,0.354 0.333,0.25 10 false *1 2.073,0.177 2.323,0.427 0.25,0.25 10 false *2 2.844,1.604 3.094,1.771 0.25,0.167 10 false *3 5.01,1.521 5.26,1.688 0.25,0.167 10 false *2 4.427,0.854 4.76,1.104 0.333,0.25 10 false *1 0.417,0.052 1.083,0.469 0.667,0.417 18 false i, ii
*1 Rear No. 1 Disc Brake Anti-squeal Shim *2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Pad Wear Indicator Plate - -


i.

Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.


ii.

Install a new rear disc brake pad wear indicator plate to each rear disc brake pad.



Hide 04466 2.INSTALL REAR DISC BRAKE PAD KIT

Z101186

CAUTION:
C456310

·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.




a.
C459267N01
0.417,0.052 0.833,0.469 0.417,0.417 18 false i

i.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.




b.
C459170C01
2.667,1.604 2.917,2.521 2.917,2.521 3.083,2.521 true 3.135,2.458 3.552,2.708 0.417,0.25 10 false *a 0.479,0.073 0.896,0.49 0.417,0.417 18 false i
*a SST or Tool Included With the Rear Disc Brake Pad Kit - -


i.

To compensate for pad lining thickness, use SST or tool included with the rear disc brake pad kit to adjust the protrusion of the rear disc brake piston by turning it.

SST
09719-12010  (09719-01030)

NOTICE:
·

Place the disc between the 2 brake pads and determine the piston return value.

·

Turn the rear disc brake piston to the position where the protrusion on the rear disc brake pad lines up properly with the piston groove.

·

Make sure the brake fluid does not overflow from the reservoir.





Hide 47850 3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C456317N01
0.417,0.042 1,0.458 0.583,0.417 18 false i

i.

Hold the rear disc brake cylinder slide pin (lower side) and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with a new bolt.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)



Hide 47877 4.INSTALL REAR DISC BRAKE DUST BOOT PROTECTOR

a.
C456308N01
0.417,0.042 1.167,0.542 0.75,0.5 18 false i

i.

Using an 8 mm socket wrench, install the rear disc brake dust boot protector to the rear disc brake cylinder assembly with the 2 bolts.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)



Hide 890C0A 5.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 46170 6.INSTALL PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Z101186

Click here(Click here)

Hide 8.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 9.INSTALL REAR WHEEL

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery , there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART